AliExpress ZK-KTD2 Trigger Cycle Timer Delay Controller

Cov ntaub ntawv khoom

Specifications:

• Khoom npe: ZK-KTD2 Trigger Cycle Timer Delay Controller
• Yam khoom naj npawb: ZK-KTD 2
• Ua hauj lwm Voltage: DC 5.0V ~ 30V
• Lub hom phiaj: Khawm/PNP/NPN/High/Low Level Signal
• High Trigger Signal: DC 3.0V ~ 24V
• Hom tso zis: Relay Switch Output (Tsis muaj voltage tso zis)
• Load (Max): DC 30V 10A lossis AC 250V 10A
• Ua haujlwm tam sim no: 50 mA
• Quiescent Current: 20 mA
• Zaub: 3Bit Liab LED Zaub Screen
• Ua haujlwm kub ntau: -40 ~ 85 ° C
• Ua haujlwm Humidity Range: 5% -95% RH
• Module Loj: 79 * 43 * 26 hli

Cov lus qhia siv khoom

Lub Sijhawm Ntev:
Lub sij hawm ntau rau ZK-KTD2 Trigger Cycle Timer Delay Controller yog txiav txim siab los ntawm lub sijhawm ncua sijhawm.

Parameter Description:

• OP: Ncua sij hawm tig rau
• CL: Ncua sij hawm tig OFF
• LOP: Tus lej ntawm lub voj voog. Qhov ntau yog 1-999 zaug. '--' txhais tau tias tsis muaj kev txwv.
• CLL: Yam tsawg kawg nkaus tus nqi ntawm random ncua sij hawm ntau. Cov txheej txheem yog 0.0 ~ 99.9 vib nas this. Qhov CLL parameter no tsuas yog siv rau P15 hom haujlwm.
• CLH: Tus nqi siab tshaj ntawm random ncua sij hawm ntau. Cov txheej txheem yog 0.0 ~ 99.9 vib nas this. Qhov CLH parameter no tsuas yog siv rau P15 hom haujlwm. CLH ntau dua CLL.

Fais fab-ON Ncua hom:
Nyob rau hauv lub hwj chim-ON ncua hom, lub ZK-KTD2 Trigger Cycle Timer ncua sij hawm Controller yuav pib qeeb tom qab fais fab tuag, tsis tas yuav muaj lwm yam teeb liab tshwm sim.

• P00: Fais fab ON thiab tso zis cia OFF thiab pib ncua sij hawm CL. Tom qab ntawd tig ON cov zis tom qab ncua sij hawm CL. Example: Fais fab ON -> OFF -> Ncua CL -> ON.
• P01: Fais fab ON thiab tso zis tig ON thiab pib ncua sij hawm OP. Tom qab ntawd tig OFF cov zis tom qab ncua sij hawm OP. Example: Fais fab ON -> ON -> Ncua OP -> OFF.
• P02: Fais fab ON thiab tso zis tig ON thiab pib ncua sij hawm OP. Tom qab ntawd tig OFF cov zis tom qab ncua sij hawm OP. Khaws OFF rau ncua sij hawm CL. Tom qab ntawd tig ON cov zis tom qab ncua sij hawm CL. Thiab tom qab ntawd loops qhov kev txiav txim saum toj no. Tus naj npawb ntawm cov voj voog (LOP) tuaj yeem teeb tsa. Cov zis yuav khaws OFF tom qab lub voj voog. Example: Fais fab ON -> ON -> Ncua OP -> OFF -> Ncua CL -> cycles -> OFF.
• P03: Fais fab ON thiab tso zis tig OFF thiab pib ncua sij hawm CL. Tom qab ntawd tig ON cov zis tom qab ncua sij hawm CL. Khaws ON rau ncua sij hawm OP. Tom qab ntawd tig OFF cov zis tom qab ncua sij hawm OP. Thiab tom qab ntawd loops qhov kev txiav txim saum toj no. Tus naj npawb ntawm cov voj voog (LOP) tuaj yeem teeb tsa. Cov zis yuav khaws ON tom qab lub voj voog. Example: Fais fab ON -> OFF -> Ncua CL -> ON -> Ncua OP -> cycles -> ON.

Pulse Signal Trigger Hom:
Hauv Pulse Signal Trigger Mode, ZK-KTD2 Trigger Cycle Timer Delay Controller yuav pib qeeb tom qab tau txais cov teeb liab tawm tswv yim.

• P04: Input trigger teeb liab thiab tso zis tig ON thiab pib ncua sij hawm OP. Tom qab ntawd tig OFF cov zis tom qab ncua sij hawm OP. Kev rov ua dua thaum lub sijhawm ncua tsis raug. Example: Trigger -> ON -> Ncua OP -> OFF.

FAQ

• Q: Dab tsi yog qhov ua haujlwm voltage ntau yam rau ZK-KTD2 Trigger Cycle Timer Delay Controller?
  Kev ua haujlwm voltage ntau yog DC 5.0V rau 30V.
• Q: Dab tsi yog qhov siab tshaj plaws uas tus ZK-KTD2 Trigger Cycle Timer Delay Controller tuaj yeem ua tau?
  ZK-KTD2 Trigger Cycle Timer Delay Controller tuaj yeem ua haujlwm siab tshaj plaws ntawm DC 30V 10A lossis AC 250V 10A.
• Q: Dab tsi yog qhov loj ntawm ZK-KTD2 Trigger Cycle Timer Delay Controller module?
  Module loj yog 79mm x 43mm x 26mm.

Nqe lus piav qhia:
ZK-KTD2 yog Relay Switch Controller Trigger Delay Module nrog Timer thiab Cycle functions.It tuaj yeem ua haujlwm hauv 16 hom kev ua haujlwm nrog lossis tsis muaj teeb meem tshwm sim.

Nta

1. 16 hom kev ua haujlwm
2. Qib siab / qis lossis PNP / NPN teeb liab
3. Fais fab-ON trigger
4. Button switch trigger
5. 2200W 10A Relay Tsav Tsheb
6. Txhawb nqa parameter nco muaj nuj nqi
7. Txhawb UART kev sib txuas lus muaj nuj nqi
8. Optocoupler cais tawm
9. Txhawb nqa yuam kev ua haujlwm
10. Txhawb zog txuag hom

Tsis muaj

1. Khoom npe: ZK-KTD2 Trigger Cycle Timer Delay Controller
2. Yam khoom naj npawb: ZK-KTD 2
3. Ua hauj lwm Voltage: DC 5.0V ~ 30V
4. Lub hom phiaj: Khawm/PNP/NPN/High/Low Level Signal
5. High Trigger Signal: DC 3.0V ~ 24V
6. Hom tso zis: Relay Switch Output (Tsis muaj voltage tso zis)
7. Load (Max): DC 30V 10A lossis AC 250V 10A
8. Ua haujlwm tam sim no: 50 mA
9. Quiescent Current: 20 mA
10. Zaub: 3Bit Liab LED Zaub Screen
11. Ua haujlwm kub ntau: -40 ℃ ~ 85 ℃
12. Ua haujlwm Humidity Range: 5% -95% RH
13. Module Loj: 79 * 43 * 26 hli

Lub sijhawm ua haujlwm

1. Kev kho tsis tu ncua los ntawm 0.1 vib nas this mus rau 999 feeb.
2. Nkag mus rau qhov chaw sib cuam tshuam thaum nias khawm luv 'STOP' hauv qhov kev hloov pauv hloov pauv hloov pauv (Flashing) xaiv lub sijhawm.
3. Ua tib zoo saib rau txoj haujlwm uas tus lej lej txav thaum lub pob nyem.
4. Zaub 'XXX.' Tus lej lej hauv qhov kawg me ntsis, lub sijhawm ua haujlwm yog 1 thib ob ~ 999 vib nas this.
5. Tso saib 'XX.X' Lub kaum sab xis ntawm qhov kawg, lub sijhawm ua haujlwm yog 0.1 thib ob rau 99.9 vib nas this.
6. Zaub 'XXX' Lub kaum sab xis yog lub teeb tag nrho, lub sijhawm ua haujlwm yog 1 feeb txog 999 feeb.
7. Rau example, yog tias koj xav teeb tsa OP rau 3.2 vib nas this, txav tus lej lej mus rau qhov kawg ntawm txoj haujlwm, Screen yuav tso saib '03.2'
8. OP thiab CL tsis yog tib yam hauv kev ua haujlwm sib txawv.
9. Nws yuav tso saib OP (CL, LOP) thiab cov sij hawm ncua sij hawm los ntawm luv nias khawm SET hauv lub ntsiab zaub interface.
10. Nws tsuas yog tso saib OP thiab coj lub sijhawm ncua sijhawm hauv P1 hom los ntawm luv nias khawm SET hauv lub ntsiab zaub interface.
11. Luv nias 'SET' khawm ntawm ib txwm tso saib kom nug OP, CL, LOP tus nqi nyob rau hauv lem.

Parameter Description:

1. OP: Ncua sij hawm tig rau;
2. CL: Ncua sij hawm tig OFF;
3. LOP: Tus lej ntawm lub voj voog. Qhov ntau yog 1-999 zaug. '--' txhais tau tias tsis muaj kev txwv.
4. CLL: Yam tsawg kawg nkaus tus nqi ntawm random ncua sij hawm ntau. Cov txheej txheem yog 0.0 ~ 99.9 vib nas this. Qhov CLL parameter no tsuas yog siv rau P15 hom haujlwm.
5. CLH: Tus nqi siab tshaj ntawm random ncua sij hawm ntau. Cov txheej txheem yog 0.0 ~ 99.9 vib nas this. Qhov CLH parameter no tsuas yog siv rau P15 hom haujlwm. CLH ntau dua CLL.

HOM

Fais fab-on ncua hom:

1. ZK-KTD2 yuav pib ncua tom qab fais fab tuag. Hom no tsis tas yuav nkag mus rau lwm lub cim qhia. Lub hwj chim mov yog lub teeb liab.
2. P00: Fais fab ON thiab tso zis cia OFF thiab pib ncua sij hawm CL. Tom qab ntawd tig ON cov zis tom qab ncua sij hawm CL. Piv txwv li Fais fab ON-> OFF-> Ncua CL-> ON.
3. P01: Fais fab ON thiab tso zis tig ON thiab pib ncua sij hawm OP. Tom qab ntawd tig OFF cov zis tom qab ncua sij hawm OP. Piv txwv li fais fab ON-> ON-> Ncua OP-> OFF.
4. P02: Fais fab ON thiab tso zis tig ON thiab pib ncua sij hawm OP. Tom qab ntawd tig OFF cov zis tom qab ncua sij hawm OP. Khaws OFF rau ncua sij hawm CL. Tom qab ntawd tig ON cov zis tom qab ncua sij hawm CL. Thiab tom qab ntawd loops qhov kev txiav txim saum toj no. Tus naj npawb ntawm cov voj voog (LOP) tuaj yeem teeb tsa. Cov zis yuav khaws OFF tom qab lub voj voog. Piv txwv li Hwj chim ON-> ON-> Ncua OP-> OFF-> Ncua CL-> voj voog-> OFF.
5. P03: Fais fab ON thiab tso zis tig OFF thiab pib ncua sij hawm CL. Tom qab ntawd tig ON cov zis tom qab ncua sij hawm CL. Khaws ON rau ncua sij hawm OP. Tom qab ntawd tig OFF cov zis tom qab ncua sij hawm OP. Thiab tom qab ntawd loops qhov kev txiav txim saum toj no. Tus naj npawb ntawm cov voj voog (LOP) tuaj yeem teeb tsa. Cov zis yuav khaws ON tom qab lub voj voog. Piv txwv li Hwj chim ON-> OFF-> Ncua CL-> ON-> Ncua OP-> voj voog-> ON.

Pulse Signal Trigger Hom:

1. ZK-KTD2 yuav pib ncua tom qab cov lus qhia tawm. Hom no xav tau cov teeb liab tawm tswv yim tom qab muab lub zog ua haujlwm.
2. P04: Input trigger teeb liab thiab tso zis tig ON thiab pib ncua sij hawm OP. Tom qab ntawd tig OFF cov zis tom qab ncua sij hawm OP. Kev rov ua dua yog siv tsis tau thaum ncua sijhawm. Piv txwv li Trigger-> ON-> Ncua OP-> OFF.
3. P05: Input trigger teeb liab thiab tso zis tig ON thiab pib ncua sij hawm OP. Tom qab ntawd tig OFF cov zis tom qab ncua sij hawm OP. Rov pib ncua OP yog tias rov ua dua thaum ncua. Piv txwv li Trigger-> ON-> Ncua OP-> OFF.
4. P06: Input trigger teeb liab thiab tso zis tig ON thiab pib ncua sij hawm OP. Tom qab ntawd tig OFF cov zis tom qab ncua sij hawm OP. Nres ncua thiab tso zis tig OFF yog tias rov ua dua thaum ncua. Piv txwv li Trigger-> ON-> Ncua OP-> OFF.
5. P07: Input trigger teeb liab thiab tso zis cia OFF thiab pib ncua sij hawm CL. Tom qab ntawd tig ON cov zis tom qab ncua sij hawm CL. Piv txwv li Trigger-> OFF-> Ncua CL-> ON.
6. P08: Input trigger teeb liab thiab tso zis tig OFF thiab pib ncua sij hawm CL. Tom qab ntawd tig ON cov zis tom qab ncua sij hawm CL. Khaws ON rau ncua sij hawm OP. Tom qab ntawd tig OFF cov zis tom qab ncua sij hawm OP. Kev rov ua dua yog siv tsis tau thaum ncua sijhawm. Piv txwv li Trigger-> OFF-> Ncua CL-> ON-> Ncua OP-> OFF.
7. P09: Input trigger teeb liab thiab tso zis tig OFF thiab pib ncua sij hawm CL. Tom qab ntawd tig ON cov zis tom qab ncua sij hawm CL. Khaws ON rau ncua sij hawm OP. Tom qab ntawd tig OFF cov zis tom qab ncua sij hawm OP. Rov pib ncua OP yog tias rov ua dua thaum ncua. Piv txwv li Trigger-> OFF-> Ncua CL-> ON-> Ncua OP-> OFF.
8. P10: Input trigger teeb liab thiab tso zis tig OFF thiab pib ncua sij hawm CL. Tom qab ntawd tig ON cov zis tom qab ncua sij hawm CL. Khaws ON rau ncua sij hawm OP. Tom qab ntawd tig OFF cov zis tom qab ncua sij hawm OP. Thiab tom qab ntawd loops qhov kev txiav txim saum toj no. Tus naj npawb ntawm cov voj voog (LOP) tuaj yeem teeb tsa. Cov zis yuav khaws ON tom qab lub voj voog. Nres ncua thiab tso zis tig ON yog tias rov ua dua thaum lub voj voog. Piv txwv li Trigger-> OFF-> Ncua CL-> ON-> Ncua OP-> cycles-> ON.
9. P11: Input trigger teeb liab thiab tso zis tig ON thiab pib ncua sij hawm OP. Tom qab ntawd tig OFF cov zis tom qab ncua sij hawm OP. Khaws OFF rau ncua sij hawm CL. Tom qab ntawd tig ON cov zis tom qab ncua sij hawm CL. Thiab tom qab ntawd loops qhov kev txiav txim saum toj no. Tus naj npawb ntawm cov voj voog (LOP) tuaj yeem teeb tsa. Cov zis yuav khaws OFF tom qab lub voj voog. Nres ncua sij hawm thiab tso zis tig OFF yog tias rov ua dua thaum lub voj voog. Piv txwv li Trigger->ON-> Ncua OP-> OFF-> Ncua CL-> voj voog-> OFF.
10. P12: Input trigger teeb liab thiab tso zis tig ON thiab pib ncua sij hawm OP. Tom qab ntawd tig OFF cov zis tom qab ncua sij hawm OP. Khaws OFF rau ncua sij hawm CL. Tom qab ntawd tig ON cov zis tom qab ncua sij hawm CL. Thiab tom qab ntawd loops qhov kev txiav txim saum toj no. Tus naj npawb ntawm cov voj voog (LOP) tuaj yeem teeb tsa. Cov zis yuav khaws OFF tom qab lub voj voog. Kev rov ua dua tsis raug thaum lub voj voog. Piv txwv li Trigger->ON-> Ncua OP-> OFF-> Ncua CL-> voj voog-> OFF.

Khaws Lub Teeb Pom Kev Ua Haujlwm Hom:

1. Hom no yuav tsum khaws cov teeb liab input. Lub xeev tso zis kuj tseem yuav hloov thaum lub teeb liab tawm tswv yim tawm,.
2. P13: Khaws cov input trigger teeb liab thiab tso zis tig ON. Tom qab ntawd pib ncua sij hawm OP yog tias tshem tawm cov lus qhia tawm. Tom qab ntawd tig OFF cov zis tom qab ncua sij hawm OP. Nres ncua thiab tso zis tig ON yog tias rov ua dua thaum ncua.
3. P14: Khaws input trigger teeb liab thiab tso zis tig OFF. Tom qab ntawd pib ncua sij hawm CL yog tias tshem tawm cov lus qhia tawm. Tom qab ntawd tig ON cov zis tom qab ncua sij hawm CL. Nres ncua thiab tso zis tig OFF yog tias rov ua dua thaum ncua.

Random Delay Hom:

1. P15: Input trigger teeb liab thiab tso zis cia OFF thiab pib ncua sij hawm. Lub sijhawm ncua ntawm CLL thiab CLH. Tom qab ntawd tig ON cov zis tom qab ncua sij hawm CLL ~ CLH. Hom no kuj tuaj yeem teeb tsa PWM lub voj voog ntawm 20%, 25%, 30%, 35% rau 100% hauv 600Hz los ntawm parameter SP. (Lub sijhawm ncua sij hawm yog tus nqi sib txawv ntawm CLL thiab CLH. Lawv qhov chaw teeb tsa yog 0.0 ~ 99.9 thib ob thiab CLH ntau dua CLL.) Piv txwv li Trigger->OFF-> Ncua-> ON.

Teeb cov kauj ruam

1. Paub meej tias hom kev ua haujlwm ua ntej pib teeb hom thiab tsis muaj.
2. Khaws nias SET khawm li 2 vib nas this nkag mus xaiv hom haujlwm.
3. Nias UP thiab Down khawm hloov ua haujlwm hom P00 ~ P015.
4. Nias SET khawm kom teeb tsa tus nqi rau kev xaiv ua haujlwm xws li P03 hom haujlwm.
5. Thawj txheej parameter OP yuav flashing txog 2 vib nas this thiab tso saib tus nqi parameter.
6. Nias STOP khawm kom txav tus lej lej thiab teem sijhawm ncua sijhawm.
7. Nias UP thiab Down khawm kom teem OP parameter tus nqi.
8. Nias SET khawm kom teeb tsa tus nqi thib ob CL. Ces teem sij hawm ntau thiab parameter tus nqi raws li tib txoj kev.
9. Nias SET khawm kom teeb qhov thib peb parameter tus nqi LOP. Ces teem parameter raws li tib txoj kev.
   Nco tseg: '--' txhais tau tias tsis muaj kev txwv.
10. Rau P15 hom kev ua haujlwm, txheej txheem txheej txheem yog tib yam rau CLL, CLH thiab SP.
    Nco tseg: Lub sij hawm ncua yog 0.0 ~ 99.9 vib nas this ntawm hom no.
11. Khaws nias SET khawm li 2 vib nas this kom txuag tau qhov ntsuas thiab tawm hauv hom teeb tsa kom pib ua haujlwm li qub.

Ntxiv nta:

1. Nws pib pw tsaug zog muaj nuj nqi: kom nias khawm 'STOP' txog 2 thib ob hauv qhov kev ua haujlwm ib txwm ua kom qhib lossis kaw nws pib pw tsaug zog ua haujlwm.
   1. CL: Tig ON pib pw tsaug zog muaj nuj nqi.Screen yuav cia li kaw yog tias tsis muaj kev ua haujlwm li ntawm 3 feeb. Nws tuaj yeem sawv los ntawm txhua lub khawm.
   2. Od: Tig OFF pib pw tsaug zog muaj nuj nqi.
2. Enabled / Disabled tso zis los ntawm nias khawm STOP:
   1. ON: Enabled tso zis thaum ncua sij hawm OP.
   2. Tawm: Disabled tso zis. Module tsis tuaj yeem tso tawm cov teeb liab ntawm hom no.
3. Nws tsis ua haujlwm yog tso saib '000' uas tsis muaj tus lej lej tau tshwm sim. xws li kom xaus rau lub xeev ua haujlwm cyclic.

Siv cov kauj ruam:

1. Txuas txoj haujlwm voltage los ntawm input terminal.
2. Teeb hom kev ua haujlwm thiab tus nqi parameter.
3. Tshem tawm cov khoom siv hluav taws xob ua haujlwm.
4. Txuas load thiab load voltage, ua teeb liab yog tias xav tau.
5. Rov txuas lub hwj huam mov.
6. Pib ib txwm ua haujlwm nrog lossis tsis muaj teeb meem tshwm sim los ntawm kev xaiv hom haujlwm.

UART Control raws tu qauv

UART Kev Sib Txuas Lus thiab Parameter nqis
Tsis muaj.	Parameter		Tus nqi
1	Baud tus nqi		9600 XNUMXbps
2	Cov ntaub ntawv		8bit ib
3	Txhob me ntsis		1bit ib
4	Xyuas me ntsis		tsis muaj
5	Flow tswj		tsis muaj
6	raws tu qauv		MODBUS-RTU
7	Function code		0x03,0x06,0x10 (Tsuas yog txhawb peb txoj haujlwm ua haujlwm)
8	Ntaus chaw nyob		0x01~0xFF(qhov chaw nyob yog 0x01)
Tsis muaj.	txib	Muaj nuj nqi	Teeb Ntau Yam	Default	Bytes	Nyeem/Sau	Sau npe chaw nyob
1	Ntxiv	Teem lub chaw nyob ntaus ntawv	0x01 ~ 0 xFF	0 x 01	2	R/W	0000 H ua
2	Khiav	Kev ua haujlwm	0: ua haujlwm	——	2	R/W	0001 H ua
			1: Nres ua haujlwm
3	POM	Enable/Disable pw tsaug zog xeev	0: Disable	——	2	R/W	0002 H ua
			1: Pab
4	MODE	Teeb hom haujlwm	0x00f 0	——	2	R/W	0003 H ua
5	OP	Ncua sijhawm rau OP	0-999 : kuv	——	2	R/W	0004 H ua
6	OP UNIT	Teem sijhawm ncua sijhawm rau OP	0: ob	——	2	R/W	0005 H ua
			1: 0.1 II
			2: feeb
7	CL	Ncua sijhawm rau OL	0x00f 0	——	2	R/W	0006 H ua
8	CL UNIT	Teem sijhawm ncua sijhawm	0: ob	——	2	R/W	0007 H ua

		unit rau OL	1: 0.1 II
			2: feeb
9	LP	Teem lub sij hawm voj voog	1 ~ 999: Lub sijhawm txwv	——	2	R/W	0008 H ua
			—: Lub sijhawm tsis kawg
10	CLL	Teem Min tus nqi ntawm random ncua.	0 ~ 99.9s	——	2	R/W	0009 H ua
11	CLH	Teem Max tus nqi ntawm random ncua.	0 ~ 99.9s	——	2	R/W	000 AW
12	SP	Set PWM duty cycle	20% ~ 100%	——	2	R/W	000 IB
13	TRGI-GER	Input trigger signal	Rau P04 ~ P15	——	2	W	000 CH UA

Nco tseg:

1. Nws yog relay hloov tso zis, yog li nws tsis tuaj yeem tso zis voltage. Lub load kuj yuav tsum tau txuas nrog lub load voltage.
2. Nws yuav tso saib '000' yog tias nres ua haujlwm. Nws qhia txog tus lej lej thaum ua haujlwm.
3. Thov nyeem siv phau ntawv thiab cov lus piav qhia ua ntej siv.

Daim ntawv thov

1. ncua kev hloov
2. Cov txee
3. Kev tswj qhov system
4. Kev hloov kho tsheb Circuit Court
5. Tsav
6. Lub electromagnetic valve
7. Lub teeb strip

Pob:

1. 1pcs ZK-KTD2 Trigger Cycle Timer Delay Controller

Zoo siab txais tos www.amazon.com/shops/icstation | Tiv tauj peb ntawm yog icstation@hotmail.com

Cov ntaub ntawv / Cov ntaub ntawv

AliExpress ZK-KTD2 Trigger Cycle Timer Delay Controller [ua pdf] Cov lus qhia ZK-KTD2 Trigger Cycle Timer Delay Controller, ZK-KTD2, Trigger Cycle Timer Delay Controller, Cycle Timer Delay Controller, Timer Ncua Sijhawm, Ncua Tswjhwm, Tswj

Cov ntaub ntawv

• Cov neeg siv phau ntawv