HSL Secure 2-Port KVM Combiner
Quick Setup Guide

FV11D-M Secure 1-Port DVI-I Video Isolator

Secure Isolators

Models:
FV11D-M – Secure 1-Port DVI-I Video Isolator
HSL Secure 2-Port KVM Combiner Quick Setup Guide
FV11H-M – Secure 1-Port HDMI Video Isolator
FV11P-M – Secure 1-Port DisplayPort Video Isolator
FI11D-M – Secure 1-Port DVI-I KVM Isolator
FI11H-M – Secure 1-Port HDMI KVM Isolator
FI11P-M – Secure 1-Port DisplayPort KVM Isolator
HDC19412 Rev. 1.0

INTRODUCTION

HSL Secure Isolators
The secure Isolator prevents vulnerable peripherals from mediating between compromised and secure computers by ensuring that video and audio flow in a single direction.

INSTALLATION

Connecting the Isolator
Step 1 – Connect the PC to the Isolator’s PC SIDE:

1. Audio connection: For all models, connect the PC to the Isolator’s AUDIO IN port, using a 1/8″ (3.5mm) stereo plug.
2. Video connection: For all models, connect the PC to the Isolator’s VIDEO IN port, using the corresponding video cable (VGA/HDMI/DVI/DP).
3. PC keyboard and mouse connection: For FI11D-M, FI11H-M, and FI11P-M models, connect the PC to the Isolator using a USB A to USB B cable. Connect the USB A end to the PC and the USB B end to the Isolator’s COMP/MOUSE port.

Step 2 – Connect the peripherals to the Isolator’s CONSOLE SIDE:

1. Audio connection: For all models, connect the speakers to the Isolator’s AUDIO OUT port.
2. Video connection: For all models, connect the monitor/projector cable to the Isolator’s VIDEO OUT port.
3. PC keyboard and mouse connection: For FI11D-M, FI11H-M, and FI11P-M models, connect a USB mouse and keyboard, to the Isolator’s corresponding MOUSE and KB ports.

Both mouse and keyboard LEDs should light continuously.
Note: If either LED remains OFF, the Isolator does not recognize the device; use an alternative device.

Step 3 – Power ON the Isolator

1. For all models, connect the power adapter to the Isolator’s PC SIDE, DC IN port.
   Power ON the Isolator by plugging it into an AC wall outlet.
   2. The PC SIDE Power LED should light continuously. If not, check the connections.

Step 4 – Make sure the PC and display are powered ON

OPERATION

Running an EDID Capture
Before using the Isolator, run a one-time EDID capture. This prevents the continuous transfer of potentially malicious data from the display to the PC – that could infect the PC, cause data leakage, and so on.
Preparation:

• Connect the PC and all peripherals to the unit, according to the diagram.
• Make sure the PC, display, and unit are ON.

To run an EDID capture:

1. On the PC SIDE, short-click the CAPTURE button – for less than one second. Warning: Long-clicking the CAPTURE button sends the unit into an undesired loop. If this happens, restart the unit and repeat the procedure.
   At first, the EDID LED flickers for a few seconds and then lights continuously.
   Note: If the EDID LED is OFF, check the connections and that the display is powered ON. Then, repeat the procedure.
2. Restart the unit.

Note: An EDID capture needs to be performed for new installations and when changing a display.

Highseclabs.com
©2019 All rights reserved. HSL logo and product names are trademarks or service trademarks of HighSecLabs Ltd (HSL). All other marks are the property of their respective owners. Images for demonstration purposes only. This document may contain confidential and/or proprietary information of HSL Corporation, and its receipt or possession does not convey any right to reproduce, disclose its contents, or to manufacture or sell anything that it may describe. Reproduction, disclosure, or use without specific authorization from HSL Corporation is strictly prohibited.

Documents / Resources

HighSecLabs FV11D-M Secure 1-Port DVI-I Video Isolator [pdf] User Guide FV11D-M, FV11H-M, FV1H1SPL, FI11D-M, FI11H-M, FI11P-M, FV11D-M Secure 1-Port DVI-I Video Isolator, Secure 1-Port DVI-I Video Isolator, 1-Port DVI-I Video Isolator, DVI-I Video Isolator, Video Isolator, Isolator

References

• User Manual