HELTEC T096 Meshtastic Mesh Node

Overview
Specifications
| Parameters | Description |
| MCU | nRF52840 |
| LoRa Chip | SX1262 |
| Memory | 1M ROM; 256KB SRAM |
| Bluetooth | Bluetooth 5, Bluetooth mesh, BLE. |
| Storage temperature | -30~80℃ |
| Operating temperature | -20~70℃ |
| Operating Humidity | 90%(No condensing) |
| Power Supply | 3~5.5V (USB), 3~4.2(Battery) |
| Display | ST7735S, 0.96 Inch, 80(H)RGB x 160(V) |
| Active Area | 10.8 mm(H) × 21.7(V) mm |
| Hardware Resource | USB 2.0, 2 x LEDs, 2 x Buttons, 4 x SPI, 2 x TWI, 2 x UART, 4 x PWM, QSPI, I2S,
PDM, QDEC Etc. |
| Interface | Type-C USB, 1.25-2P lithium battery connector, 1.25-2P solar panel connector,
LoRa ANT (IPEX1.0), GNSS ANT (IPEX1.0), 2 x 13 x 2.54 Header Pins |
| Dimensions | 52*25.4*10.2 mm |
Power Consumption
| Mode | Condition | Consumption @3.7V_BAT |
| LoRa_TX | 152~776mA | |
|
BT |
UART | 10mA |
| Scan | 2.6mA | |
| Sleep | 13uA | |
|
Charging |
Solar | 500mA |
| USB-C | 500mA |
Product Features
- Based on nRF52840 (Bluetooth), SX1262(LoRa), and UC6580(GNSS).
- Low power consumption, 13μA in deep sleep.
- Onboard 0.96 inch TFT-LCD display contains 80(H)RGB x 160(V) dots.
- Type-C USB interface with a complete voltage regulator, ESD protection, short circuit protection, RF shielding, and other protection measures.
- CN3165 lithium battery charge management IC features built-in adaptive current regulation for efficient and safe charging.
- Various Interfaces: 2*1.25 LiPo connector, 2*1.25 Solar panel connector.
- Compatible with Arduino,and we provide Arduino development frameworks and libraries.
1.3 Typical Application Scenarios
- Decentralized Outdoor Mesh Communication
- Asset Tracking and Position Monitoring
- Emergency and Disaster Communication Networks
- Environmental Monitoring and Remote Sensing
- Open-Source Mesh Experimentation and Education
- Portable Personal Communication Device
Pin Definition
About SPI, I2C, UART, PWM, QPSI, I2S, PDM, QDEC: Each IO pin is preconfigured with IO_MUX functionality, which means you can use any GPIO as peripheral pins. You just need to define these pins in your code. However, it’s important to note that once a pin is used, it may affect other functions associated with that pin. For information, please refer to the Schemaic diagram.

P2
| PHY | Name | Type | Description |
| 1 | GND | P | Ground |
| 2 | 5V | P | 5V Power |
| 3 | GND | P | Ground |
| 4 | Vext | P | 3V3 output |
| 5 | GND | P | Ground |
| 6 | Vext | P | 3V3 output |
| 7 | P0.07 | I/O | GPIO0.07 |
| 8 | P0.08 | I/O | GPIO0.08 |
| 9 | SWDCLK | I/O | SWD Clock |
| 10 | SWDIO | I/O | SWD Data |
| 11 | P0.27 | I/O | GPIO0.27 |
| 12 | P0.04 | I/O | GPIO0.04, ADC2 |
| 13 | P1.03 | I/O | GPIO1.03 |
| 14 | P1.05 | I/O | GPIO1.05 |
| 15 | P1.07 | I/O | GPIO1.07 |
| 16 | P1.06 | I/O | GPIO1.06 |
| 17 | P1.02 | I/O | GPIO1.02 |
| 18 | P1.04 | I/O | GPIO1.04 |
| 19 | P0.23 | I/O | GPIO0.23, GNSS_TX |
| 20 | P0.25 | I/O | GPIO0.25, GNSS_RX |
P3
| PHY | Name | Type | Description |
| 1 | GND | P | Ground |
| 2 | VDD | P | VDD_nRF |
| 3 | P0.31 | I/O | GPIO0.31, ADC7 |
| 4 | P0.29 | I/O | GPIO0.29, ADC6 |
| 5 | P0.02 | I/O | GPIO0.02, ADC0 |
| 6 | P1.15 | I/O | GPIO1.15, ADC_Ctrl(high enable) |
| 7 | P1.13 | I/O | GPIO1.13 |
| 8 | P0.10 | I/O | GPIO0.10 |
| 9 | P0.09 | I/O | GPIO0.09 |
| 10 | P1.10 | I/O | GPIO1.10, User Button |
| 11 | P0.18 | I/O | GPIO0.18, Reset |
| 12 | P0.22 | I/O | GPIO0.22, CS |
| 13 | P1.11 | I/O | GPIO1.11, PPS |
| 14 | P0.20 | I/O | GPIO0.20, SCLK |
| 15 | P0.17 | I/O | GPIO0.17, SDIN |
| 16 | P0.15 | I/O | GPIO0.15, RS |
| 17 | P0.13 | I/O | GPIO0.13, RES |
| 18 | P1.01 | I/O | GPIO1.01 |
| 19 | P1.00 | I/O | GPIO1.00 |
| 20 | P0.24 | I/O | GPIO0.24 |
Unrouted pins
| Name | Number | Function |
| P0.26 | GPIO0.26 | Vext Ctrl (high enable) |
| P0.03 | GPIO0.03 | ADC IN |
| P0.21 | GPIO0.21 | DIO1 |
| P0.05 | GPIO0.05 | LoRa NSS |
| P1.08 | GPIO1.08 | LoRa_SCK |
| P0.11 | GPIO0.11 | LoRa_MOSI |
| P0.14 | GPIO0.14 | LoRa_MISO |
| P0.16 | GPIO0.16 | LoRa_RST |
| P0.19 | GPIO0.19 | LoRa_BUSY |
| P0.06 | GPIO0.06 | VGNSS_Ctrl(low enable) |
| P1.14 | GPIO1.14 | GNSS_RST |
| P0.30 | GPIO0.30 | FEM_Ctrl |
| P0.12 | GPIO0.12 | PA_CSD |
| P0.28 | GPIO0.28 | White LED |
| P1.12 | GPIO1.12 | Display LED |
| P1.09 | GPIO1.09 | PA CTX |
Physical Dimensions

Resource
- Mesh Node T096 Schematic Diagram
- SDK: Heltec nRF52 framework and Lib
- SnapEmu LoRaWAN IoT Platform
- Mesh Node T096 Manual Document
- TFT-LCD Datasheet
- GNSS Documents
Heltec Contact Information
Heltec Automation Technology Co., Ltd Chengdu, Sichuan, China
- Email: support@heltec.cn
- Phone: +86-028-62374838
- https://heltec.org
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly approved by the party. Responsible for compliance could void the authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
The equipment complies with FCC Radiation exposure limits set forth for uncontrolled enviroment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
Copyright Notice
All contents in the files are protected by copyright law, and all copyrights are reserved by Chengdu Heltec Automation Technology Co., Ltd. (hereinafter referred to as Heltec). Without written permission, all commercial use of the files from Heltec are forbidden, such as copy, distribute, reproduce the files, etc., but non-commercial purpose, downloaded or printed by individual are welcome.
Disclaimer
Chengdu Heltec Automation Technology Co., Ltd. reserves the right to change, modify or improve the document and product described herein. Its contents are subject to change without notice. These instructions are intended for you use.
Troubleshooting
- Low-power operation expectations: If battery life is not as expected, verify your operating mode. The documented consumption includes Sleep at -13 μA and Scan at 2.6 mA at 3.7V_BAT, while LoRa TX can draw 152~776 mA and BT UART 10 mA.
- Unexpected behavior when using pins: If firmware fails or peripherals behave incorrectly, confirm that the GPIO/pin assignments in your code match the intended functions. The manual notes that using a pin can affect other functions on that same pin.
Documents / Resources
![]() | T096 Meshtastic Mesh Node |
References
- github.com/HelTecAutomation/Heltec_nRF52github.com
- heltec.orgheltec.org
- platform.snapemu.com/user/loginplatform.snapemu.com
- resource.heltec.cn/download/Mesh_Node_T096/Schematicresource.heltec.cn
- resource.heltec.cn/download/UC6580resource.heltec.cn
- resource.heltec.cn/download/Wireless_Tracker_V2/Display_Datasheet/SPEC%20N096-1608TBBIG09-C08%20VER%20A.pdfresource.heltec.cn
- wiki.heltec.org/docs/devices/open-source-hardware/nrf52840-series/mesh-node-t096/wiki.heltec.org
- User Manualmanual.tools

