HelloRadioSky V15 Remote Controller User Manual

HelloRadioSky-V15-Remote-Controller-logo

HelloRadioSky V15 Remote Controller

HelloRadioSky-V15-Remote-Controller-product

Overview

The HelloRadioSky V15 is a versatile radio system designed for fixed-wing aircraft, gliders, helicopters, and multi-rotors. Use the quick start reference for safe operation, charging guidance, model/protocol selection (ExpressLRS), and basic setup steps.

Specifications

Size 175 × 178 × 55 mm (antennas folded)
Weight 730 g (no battery included, with metal gimbals)
Transmission Frequency 2.400 GHz – 2.480 GHz
Working Current 450 mA
Working Voltage 6.6 – 8.4 V DC
Radio Firmware EdgeTX
Module Bay Compatible with micro JR/FrSKY bay modules (e.g., Multi-Protocol-Module, ExpressLRS, Ghost, TBS Crossfire, TBS Tracer)
Upgrade Method Supports USB-C online / SD card offline upgrade
Approved Battery Types (assembled as 7.4 V 2S packs) 2× 3.7 V Li-ion 18650 cells; 2× 3.7 V Li-ion 21700 cells; 2× 3.7 V Lithium-polymer cells

Quick Guide

  1. Power on: Install the batteries, then press and hold SYS and MDL simultaneously for a few seconds.
  2. Charge (USB-C): Use the built-in USB-C charging only for 2S 7.4 V battery configurations with nominal 3.7 V cells and a maximum charge cut-off voltage of 4.2 V.
  3. Before charging: Turn off both the internal and external RF modules.
  4. Recommended while charging: Avoid operating the radio while it is charging.
  5. ExpressLRS binding: Turn off the transmitter.
  6. Cycle power to the receiver 3 times, waiting for the receiver LED to light up each time; the receiver LED will blink rapidly in bind mode.
  7. Turn on the transmitter, open the ExpressLRS LUA script interface, and select the [BIND] command.
  8. Wait for the receiver LED to turn solid, indicating a successful bind.
Safety & Precautions
Many radio control models are equipped with powerful motors and sharp spinning propellers. Please exercise caution when working on models. Ensure power is disconnected from your models and remove propellers when performing maintenance or assembly. Do not operate the V15 radio system under the following conditions:
  • During bad weather or high wind conditions such as rain, hail, snow, storms, or electromagnetic events.
  • Under limited or restricted visibility in any situation.
  • In areas where people, property, high-voltage powerlines, public roads, vehicles, or animals may be present.
  • If you are feeling tired, unwell, or under the influence of drugs or alcohol.
  • If the radio or model appear to be damaged or not functioning correctly.
  • In areas of high 2.4GHz interference or in locations where use of 2.4GHz radios is prohibited by local regulations.
  • When the battery in the V15 or the model is too low to function.

CAUTION
The V15 is shipped with the most stable firmware at the time of manufacture. Please only update firmware if you are experienced and confident in updating system firmware. Incorrect updates may render the radio inoperable. DO NOT charge 6.6v LiFE battery packs or Li-ion 18650 cells with nominal voltage of 3.6v. Incorrectly charging the wrong battery type may lead to damage of the radio or fire.

Antenna Separation Distance
When operating your HelloRadioSky transmitter, please be sure to maintain a separation distance of at least 20 cm between your body (excluding fingers, hands, wrists, ankles and feet) and the antenna to meet RF exposure safety requirements as determined by FCC regulations. Please follow your local laws and regulations regarding the radio power and frequency. Regularly check the health and condition of your batteries and never leave your radio charging unattended. Always charge in a safe area away from combustible materials and surfaces. Do not charge if your radio becomes wet or damaged in any way. HelloRadioSky does not accept any liability for the use or misuses of this product.

Remote control

HelloRadioSky-V15-Remote-Controller-figure-1 HelloRadioSky-V15-Remote-Controller-figure-2

Power On
Install the batteries. Press and hold SYS and MDL keys simultaneously for a few seconds to power on the radio.

Power Requirements and Charge
The V15 has built in USB-C charging for 3.7V lithium cells. The Charging circuit is designed for 2x 3.7v Li-ion 18650 unprotected cells or 2x 3.7v Li-poly cells (2s 7.4v LiPO pack) only with a nominal cell voltage of 3.7v and maximum charge capacity of 4.2v. Please turn off the internal and external RF modules during charging, and it is suggested not to operate the radio during charging.

Model and protocol selection (ELRS)

HelloRadioSky-V15-Remote-Controller-figure-3

Bind method:

  1. Turn off the radio.
  2. Cycle power to the receiver 3 times, the receiver LED will start blinking, indicating it’s in bind mode.
  3. Turn on the radio, enter the ExpressLRS LUA, and select Bind.
  4. The receiver LED will now stay illuminated, signaling a successful bind process.

Support, Warranty and Repairs
Please retain your proof of purchase and contact the retailer you purchased your V15 from, should you experience any problems with your radio hardware. Warranty is valid for one year from the date of purchase.

FCC statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Full text of the declaration of conformity is available at the following website: www.HelloRadioSky.com

Troubleshooting

  • If the radio or model appears damaged or not functioning correctly: Stop using it and do not operate in that condition.
  • Verify charging safety if charging is problematic: Do not charge the radio with wet or damaged conditions; never charge incorrect battery types/voltages (incorrect charging may cause severe damage, thermal runaway, or fire).
  • If binding does not succeed: Ensure the receiver is in bind mode (receiver LED blinking rapidly) by cycling receiver power 3 times and then performing the [BIND] command in the ExpressLRS LUA script interface; successful binding results in the receiver LED turning solid.
  • If you experience issues related to RF environment: Do not operate during electromagnetic events, and avoid operating in areas with high 2.4 GHz interference or where 2.4 GHz radio use is prohibited by local regulations.
  • Seek support for hardware issues: If you experience problems with the V15 radio hardware, contact the retailer from whom you purchased the V15.

Documents / Resources

PDF thumbnailV15 Remote Controller
User Manual · HelloRadioSky, ShenZhen HelloRadioSky Technology Co. Ltd, V15, remote controller, radio controller

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.