HDWR HD580 Code Reader
Specifications
- Warranty: 2 years
- Light Source: 617nm CMOS LED
- Scanning method: manual (on the button) / automatically (after bringing the code closer)
- Scan confirmation: light and sound
- Interface: USB, Virtual COM-USB
- Cable length: 170 cm
- Device dimensions: 16.5 x 8.5 x 7 cm
- Receiver dimensions: 2 x 1.5 x 0.6 cm
- Package dimensions: 16.5 x 10 x 8 cm
- Reader weight: 175 g
- Weight with packaging: 240 g
- Operating Temperature: -20~50°C
- Storage Temperature: -40~70°C
- 1D code readable: UPC-A, UPC-E, EAN-8, EAN-13, Code 128, Code 39, Code 93, Code 11, Interleaved 2 of 5 (ITF), Matrix 2 of 5, Standard 2 of 5, Coda bar, MSI Plessey, GS1, China Post, Databar(RSS), Korea, NEC 2 of 5, other one-dimensional
- Readable 2D codes: QR Code, Data Matrix, PDF417, Aztec, Maxicode
Set contents
- Wired 1D/2D Code Reader
- USB Communication Cable
- Original manufacturer’s user manual
Features
- Scanning: manual (push-on) / automatic (when the code is brought closer)
- Types of barcodes scanned: 1D, 2D barcodes (e.g. QR) from paper labels and from the phone screen and LCD and LED/OLED
- Scan confirmation: light and sound
- Available interfaces: USB, Virtual COM-USB
- Additional features: Setting any character as prefix and suffix, Virtual COM function
Factory reset
Setting the suffix
Barcode scanning mode
Case settings 
Beep settings 
- After scanning the “Beep off” code, you need to scan the “Factory Reset” code to turn the sound back on.
Interface settings 
Setting the reading delay for the same barcode
- It is possible to set the time in which the scanner should not scan again the same barcode that has already been read once.
Barcode settings
- Scanning 1D codes
- 2D Code Scanning
- Scanning reversed codes
- Keyboard Type Setting
Hide characters in a barcode
- Hiding leading characters
- To hide the initial characters of the barcode, you must first scan the “On” code that activates character hiding. Then read the code “Hiding initial characters”. Finally, you need to scan the appropriate numerical code, defining the number of digits to hide.
Example: The barcode is “123456789”. The first two digits are to be hidden. In this case, scan the code “0”, “0”, “2”. The barcode will appear as “3456789” when it is scanned again.
- Hiding trailing characters
- In order to hide the trailing characters of the barcode, first scan the “Enabled” code, which activates character hiding. Then read the code “Hiding trailing characters” and finally scan the appropriate numeric code, defining the number of digits to hide.
Example: The code is “123456789”. The last two signs are to be hidden. To do this, scan the code “0”, “0”, “2”. The code will be in the form of “1234567”.
Set Prefix and Suffix 
In order to set a prefix or suffix, first scan the “Add prefix” or “Add suffix” code. Then read the appropriate codes from Annexes 1 and 3, which are to be used as a suffix. To complete the process of adding a prefix/suffix, it is necessary to scan the code “Finish Settings” and finally “Output Settings”.
Example: The code is “123456789”. The suffix is to be the B1 sign. To do this, scan the codes “1”, “0”, “6”, “6”, “1”, “0”, “4”, “9” from attachment number 1. (In addition, the number 3 character B has the value 1066 and the character 1 has the value 1049)
Attachment 2. Barcode ID
FAQ
- Q: How do I reset the device to factory settings?
A: To perform a factory reset, navigate to the Factory Setting option in the menu and follow the on-screen instructions. - Q: How can I adjust the beep volume?
A: You can set the beep volume to High, Average, or Low in the Beep settings menu. - Q: How do I add a prefix or suffix to scanned barcodes?
A: Scan the Add prefix/suffix code, then scan the appropriate codes from Annexes 1 and 3 for prefix/suffix selection.
Documents / Resources
 |
HDWR HD580 Code Reader [pdf] User Manual HD580, HD580 Code Reader, Code Reader, Reader |