HDWR Global AC900HF Standalone RFID Access Controller
Specifications
- Warranty: 1 year
- Device Type: Standalone Access Controller
- Verification Type: RFID Card, Password
- Operating frequency: 13.56 mHz
- Max number of employees in the base: 1000
- Reading distance: 2-10cm
- Keyboard and keys: touch
- Readable Chip Types: Mifare
- Interface: Wiegand 26
- Operating Voltage: DC 12V +- 12%
- Working Current: 1.2A
- Lock relay: DC 12V/3A
- Operating temperature: 0°C ~ 45°C
- Operating Humidity: 40% – 90%
- Product dimensions: 12.3 x 8.4 x 2.3 cm
- Package dimensions: 18.5 x 13.9 x 5.5 cm
- Product weight: 200 g
- Product weight with packaging: 400 g
Set contents:
- Standalone Access Controller
- Manual
Product Usage Instructions
Default Settings:
- Password: 123456
- Backlight: Automatic
- Wiegand 26 Opening Mode: Shared
Access Control Status:
- Red LED:
- Flashes every 1 second slowly – Standby
- On all the time – Programming mode
- Green LED:
- On all the time – Unlock Mode
- Flashes quickly every 0.5 seconds – Waiting for further actions
Features
- Can be connected directly to the electronic lock and doorbell
- Verification via RFID card and password
- 13.56 mHz operating frequency and DC12V operating voltage
Default settings
|
Password |
123456 |
Shared access
password |
lack |
|
Backlight |
Automatic |
Relay Unlocking
Output |
5 seconds |
| Wiegand 26 | Input | Safe Mode | disabled |
|
Opening Mode |
Access card or password
An access password includes a private access password (PIN) and a shared access password |
||
Light and sound signals
Light Signal: Red and Green
| Description of the light signal | Access Control Status |
| Red LED flashes every 1 second
slowly |
Standby |
| Red LED on all the time | Programming mode |
| The green LED is on all the time | Unlock Mode |
| Green LED flashes quickly
every 0.5 seconds |
Waiting for further actions |
Sound signal: buzzer
| Description | Access Control Status |
| 1 short beep | Valid input |
| 3 short beeps | Invalid input |
| 1 long beep | Operation success |
| A continuous, long beep | Restoring Factory
Programming Passwords |
Connection Instructions
| Lp. | Designation | Colour | Function |
| 1 | +12V | Red | Power + |
| 2 | GND | Black | Power- |
| 3 | PUSH | Blue | Low Output Signal |
| 4 | OPEN | Yellow | Unlocking the door |
| 5 | BELL | Grey | Bell |
| 6 | BELL | Violet | Bell |
| 7 | DATA0 | Green | Wiegand DATA0 |
| 8 | DATE1 | White | Wiegand DATA1 |
| 9 | NC | Brown | NC relay output |
| 10 | COM | Orange | Relay Output Com |
| 11 | YES | Pink | Relay output NO |
Connection diagram
Remark: If the relay has an electrical interlock, the “+” and “-” poles of the interlock must be connected in reverse.
Detailed programming instructions
Basic functions
| Purpose | Operation to be
performed |
Comments |
| Changing the programming password | # Programming password # 0 new programming password # | If you lose the programming password, use the default password
(123456) |
| Add a user card | # Programming password #1 card
reading # |
If you want to add several cards, read
them continuously |
| Set a common access password | # Programming password #21 new common password # | There is only one common access password. Choose a method: Shared
access password # |
| Delete all users | # Programming password #40 0000 # | Delete all cards and PINs except for a
shared password |
| Removing a user by reading the card | # programming password 41 read card
# |
To remove multiple cards, read the cards
continuously |
| Purpose | Operation to be
performed |
Comments |
| Add a private access password (PIN) | # Programming password # 22 PIN # | There can be many PIN codes |
| Add a card by entering the card number | # Programming password #23 enter
card number # |
The card number is 10- digit or 8-digit |
| Adding multiple cards by entering the card number | # programming password # 24 enter the number of the starter card number
number of cards # |
The number of cards should be 4 digits (if you are adding twenty cards at a time, enter
0020). |
| Add a card + PIN | # programming password # 3 read PIN
card # |
|
| Deleting a user by entering a user ID
number |
# programming password #42 enter
user ID # |
|
| Deleting a user by entering a card
number |
# Programming password #43 Enter
card number # |
The card number is 10- digit or 8-digit |
| Remove a user by entering a PIN | # programming password # 44 enter
PIN number # |
PIN consists of 3~6 digits |
| Remove all users’ PIN | # programming password # 45 1111 # | Applicable to user PIN codes (does not include cards and PIN
codes + card) |
| Changing the opening time | # programming password # 5 XX # | XX can be 2-digit, and max. is 99. If 00 is entered, the signal
output time is 0.2 s. |
| Set open mode | # programming
password # 6 XX # |
XX can be 01 (card
only) /02 (card or |
| access password) /03
(card + PIN) |
||
| Reading Setting | # programming password #6 04 # | The device can be used as a reader (W26
output) |
| Setting the safety function
Anti-disconnection alarm setting |
# programming password # 7 XX # | XX can be 01/02 (safety function OFF/ON) and 03/04 (distance alarm
OFF/ON). |
| Note: Enabled security feature means that the system will be locked for 5 minutes if it reads an unregistered card or the wrong access
password is entered 10 times |
||
| Backlight Setting | # programming
password # 8 XX # |
XX can be 01/02/03
(Off/On/Automatic) |
| Factory reset | # programming password # 8 99 # | Except for the programming password and admin
tab |
| Admin tab setting | # programming password #91 read 1 card read 2 cards | The first tab read is the tab added by the administrator, and the second tab is the card removed by the
administrator |
Reset the programming password
To reset to the factory programming password (123456):
- Turn off the power and connect 2 and 3 RST(S1)
- Turn on the power, the buzzer will beep 3 long times and the green LED will flash. If you need to set an administrator card, read two blank tabs: the first as adding an administrator and the second as removing an administrator card, the second as Removing an administrator card: red LED flashes, a continuous short beep.
- Turn off the power, unplug container 2 and 3, and connect container 1 and 2 RST.
- Turn the power back on.
How to use the admin tab
- To add a standby user card, follow these steps: Read admin card read new card reread admin card
- To remove a standby user card, follow these steps: Read admin card read the registered card reread the admin card
To remove all standby users, follow these steps:
User cards can be added or removed continuously.
What is a user ID number
A user ID is an automatically generated 4-digit number that starts with 0001. The number increases as you add the user one by one and ignores the deletion of the user. The shared access password does not have an ID number.
PIN code change (in open mode: card + PIN)
After reading the card and entering the corresponding PIN code to open the door, within 5 seconds, press and hold the # button until the green LED flashes rapidly, then enter the new PIN code # new PIN code again #. A long beep indicates the successful change of the PIN code.
FAQ
Q: What should I do if I lose the programming password?
A: Use the default password (123456) to reset.
Documents / Resources
 |
HDWR Global AC900HF Standalone RFID Access Controller [pdf] User Manual AC900HF, AC900HF Standalone RFID Access Controller, AC900HF, Standalone RFID Access Controller, RFID Access Controller, Access Controller, Controller |