Boardcon Embedded Design Compact3566 Embedded Development Board
Hoʻolauna
No keia Manual
Kuhi ʻia kēia manual e hāʻawi i ka mea hoʻohana me ka overview o ka papa a me nā pōmaikaʻi, nā kikoʻī kikoʻī piha, a me nā kaʻina hana. Aia kekahi ʻike palekana koʻikoʻi.
Manaʻo manaʻo a me ka hōʻano hou i kēia Manual
No ke kōkua ʻana i kā mākou mea kūʻai e hana i ka hapa nui o kā mākou huahana, ke hoʻomau nei mākou i nā kumuwaiwai hou aʻe i loaʻa ma ka Boardcon webkahua pūnaewelewww.boardcon.com , www.armdesigner.com).
Hoʻopili kēia i nā manual, nā palapala noi, nā polokalamu examples, a me ka lako polokalamu a me ka lako.
E nānā i kēlā me kēia manawa e ʻike i nā mea hou!
Ke hoʻomaka nei mākou i ka hana ma kēia mau kumuwaiwai hou, ʻo ka pane ʻana mai nā mea kūʻai aku ka helu hoʻokahi
manaʻo, inā he nīnau kāu, manaʻo, a hopohopo paha e pili ana i kāu huahana a papahana paha, e ʻoluʻolu e hoʻokaʻaʻike mai iā mākou ma support@armdesigner.com.
Palekana Palekana
Hoʻopaʻa ʻo Boardcon i kēia huahana me ka ʻole o nā hemahema o ka waiwai a me ka hana ʻana no hoʻokahi makahiki mai ka lā i kūʻai ʻia ai. I loko o kēia manawa hōʻoia e hoʻoponopono a hoʻololi paha ʻo Boardcon i ka ʻāpana hemahema e like me ke kaʻina hana:
Pono e hoʻokomo ʻia kahi kope o ka invoice kumu i ka wā e hoʻihoʻi ana i ka ʻāpana hemahema i Boardcon. ʻAʻole uhi kēia palapala hoʻokō palena i nā pōʻino ma muli o ke kukui a i ʻole ka hoʻonui ʻana i ka mana, ka hoʻohana hewa ʻana, ka hana ʻino, nā kūlana ʻano ʻole o ka hana, a i ʻole ka hoʻāʻo e hoʻololi a hoʻololi i ka hana o ka huahana.
Ua kaupalena ʻia kēia palapala hōʻoia i ka hoʻoponopono ʻana a i ʻole ka hoʻololi ʻana i ka ʻāpana hemahema. ʻAʻole e hoʻopiʻi a kuleana paha ʻo Boardcon no nā poho a i ʻole nā poino, e komo pū ana akā ʻaʻole i kaupalena ʻia i nā waiwai nalowale, nā pōʻino kūpono ʻole a i ʻole ka hopena, nā poho o ka ʻoihana, a i ʻole nā waiwai mua e kū mai ana mai ka hoʻohana ʻana a i ʻole hiki ke hoʻohana i kēia huahana.
Hana ʻia nā hana hoʻoponopono ma hope o ka pau ʻana o ka manawa hōʻoia e pili ana i ka uku hoʻoponopono a me ke kumukūʻai o ka hoʻihoʻi ʻana. E ʻoluʻolu e kelepona iā Boardcon no ka hoʻonohonoho ʻana i nā lawelawe hoʻoponopono a loaʻa i ka ʻike uku hoʻoponopono.
Compact3566 Introduction
Hōʻuluʻulu manaʻo
ʻO ka Compact356 kahi papa kamepiula papa hoʻokahi ʻo Rockchip's RK3566 he quad-core Cortex-A55, Mali-G52 GPU, a me 1 TOPs NPU. Kākoʻo ia i ka decode wikiō 4K.
Hoʻolālā ʻia ia no nā mea AIoT e like me ka mea hoʻokele ʻenehana, nā mea IoT, nā mea hoʻopili akamai, nā kamepiula pilikino a me nā robots. Hiki i ka hana kiʻekiʻe a me ka haʻahaʻa haʻahaʻa haʻahaʻa ke kōkua i nā mea kūʻai aku e hoʻolauna i nā ʻenehana hou me ka wikiwiki a hoʻonui i ka pono o ka hopena holoʻokoʻa.
Nā hiʻohiʻona
- Microprocessor
- Quad-core Cortex-A55 a hiki i ka 1.8G
- 32KB I-cache a me 32KB D-cache no kēlā me kēia kumu, 512KB L3 cache
- 1 TOPS ʻĀpana Kaʻina Neural
- Mali-G52 a hiki i ka 0.8G
Hui Hoʻomanaʻo - LPDDR4 RAM a hiki i 8GB
- EMMC a hiki i 128GB
- Boot ROM
- Kākoʻo i ka hoʻoiho ʻana i nā code ʻōnaehana ma o USB OTG a i ʻole SD
- Pūnaehana Kaiapuni Trust Execution
- Kākoʻo i ka OTP paʻa a me ka mīkini cipher lehulehu
- Video Decoder/Encoder
- Kākoʻo i ka hoʻololi wikiō a hiki i 4K@60fps
- Kākoʻo H.264 encode
- H.264 HP hoʻopili a hiki i 1080p@60fps
- Nui kiʻi a hiki i 8192×8192
- Hōʻike Subsystem
- Hoʻopuka wikiō
Kākoʻo HDMI 2.0 transmitter me HDCP 1.4/2.2, a hiki i 4K@60fps
Kākoʻo 4 ala MIPI DSI a hiki i 2560 × 1440@60Hz
A i ʻole LVDS interface a hiki i 1920×1080@60Hz - Kiʻi ma
Kākoʻo ʻo MIPI CSI 2lanes interface
- Hoʻopuka wikiō
- Leo
- ʻO ka hoʻopuka stereo stereo a me ka hoʻokomo MIC
- Kākoʻo MIC array a hiki i ka 4ch PDM/TDM interface
- Kākoʻo I2S/PCM interface
- Hoʻokahi puka SPDIF
- USB a me PCIE
- ʻEkolu mau kikowaena USB 2.0
- Hoʻokahi USB 2.0 OTG, a ʻelua mau pūʻali USB 2.0
- Hoʻokahi USB 3.0 host
- Hoʻokahi kikowaena PCIE a i ʻole SATA no M.2 SSD.
- Ethernet
- Kākoʻo i ka 10/100/1000Mbit/s ka helu hoʻoili ʻikepili
- I2C
- A hiki i ʻelua I2C
- Kākoʻo i ke ʻano maʻamau a me ke ʻano wikiwiki (a hiki i 400kbit/s)
- SD
- Kākoʻo kākoʻo Kākoʻo SD Micro
- SPI
- A hiki i ʻelua mau mea hoʻokele SPI,
- Pākuʻi paʻi kiʻi piha-duplex
- UART
- Kākoʻo a hiki i ʻEhā mau mea hoʻohana UART
- Debug UART ma o micro-USB
- ADC
- Kī ADC ma ke kelepona
- PWM
- Kākoʻo iā 10 PWM
- Kākoʻo i ka manawa 32bit / hale kūʻai
- Koho IR ma PWM3/7/15
- Hui mana
- Hoʻokahi 5V@2A hoʻokomo
- Pākuʻi CR1220 Cell no RTC
- Kākoʻo 5V PoE + mana module
RK3566 Palapala Kiʻi
Compact3566 PCB Ana
Hoʻohālikelike Pin Compact3566
| GPIO | hōʻailona | ʻO ka wehewehe a i ʻole nā hana | GPIO serial | IO Voltage |
| 1 | VCC3V3_SYS | 3.3V IO mana puka (Max:0.5A) | 3.3V | |
| 2 | VCC5V_SYS | 5V Main Mana komo | 5V | |
| 3 | I2C3_SDA_M0 | PU 2.2K/ UART3_RX_M0 | GPIO1_A0_u | 3.3V |
| 4 | VCC5V_SYS | 5V Main Mana komo | 5V | |
| 5 | I2C3_SCL_M0 | PU 2.2K/ UART3_TX_M0 | GPIO1_A1_u | 3.3V |
| 6 | GND | Ka honua | 0V | |
| 7 | GPIO0_A3_u | 3.3V | ||
| 8 | GPIO3_C2_d | UART5_TX_M1 | 3.3V | |
| 9 | GND | Ka honua | 0V | |
| 10 | GPIO3_C3_d | UART5_RX_M1 | 3.3V | |
| 11 | GPIO1_B1_d | PDM_SDI2_M0 (V2 hoʻololi) | 3.3V | |
| 12 | GPIO4_C3_d | SPI3_MOSI_M1/I2S3_SCLK_M
1 (V2 hoʻololi) |
PWM15_IR_M1 | 3.3V |
| 13 | GPIO0_A5_d | 3.3V | ||
| 14 | GND | Ka honua | 0V | |
| 15 | GPIO0_A6_d | 3.3V | ||
| 16 | GPIO0_B7_d | PWM0_M0 | 3.3V | |
| 17 | VCC3V3_SYS | 3.3V IO mana puka (Max:0.5A) | 3.3V | |
| 18 | GPIO0_C2_d | PWM3_IR | 3.3V | |
| 19 | GPIO0_B6_u | SPI0_MOSI_M0/ I2C2_SDA_M0 | PWM2_M1 | 3.3V |
| 20 | GND | Ka honua | 0V | |
| 21 | GPIO0_C5_d | SPI0_MISO_M0 | PWM6 | 3.3V |
| 22 | GPIO0_A0_d | REFCLK_OUT | 3.3V | |
| 23 | GPIO0_B5_u | SPI0_CLK_M0/ I2C2_SCL_M0 | PWM1_M1 | 3.3V |
| 24 | GPIO0_C6_d | SPI0_CS0_M0 | PWM7_IR | 3.3V |
| 25 | GND | Ka honua | 0V | |
| 26 | GPIO0_C4_d | SPI0_CS1_M0 | PWM5 | 3.3V |
| 27 | I2C1_SDA | PU 2.2K | (Meka1) | 3.3V |
| 28 | I2C1_SCL | PU 2.2K | (Meka1) | 3.3V |
| 29 | GPIO1_A6_d | UART4_TX_M0/PDMCLK0_M0
(V2 hoʻololi) |
3.3V | |
| 30 | GND | Ka honua | 0V | |
| 31 | GPIO1_A4_d | UART4_RX_M0/PDMCLK1_M0
(V2 hoʻololi) |
3.3V | |
| 32 | GPIO0_C7_d | (V2 hoʻololi) | PWM0_M1 | 3.3V |
| 33 | GPIO4_C2_d | SPI3_CLK_M1/I2S3_MCLK_M1
(V2 hoʻololi) |
PWM14_M1 |
3.3V |
| 34 | GND | Ka honua | 0V | |
| 35 | GPIO4_C4_d | SPDIF_TX_M2/I2S3_LRCK_M1/ SATA2_ACT_LED (V2 hoʻololi) | 3.3V | |
| 36 | GPIO4_D1_u | SPI3_CS1_M1(V2-1208 update) | (Meka2) | 3.3V |
| 37 | GPIO1_B2_d | PDM_SDI1_M0 (V2 hoʻololi) | 3.3V | |
| 38 | GPIO4_C6_d | UART9_RX_M1/SPI3_CS0_M1/ I2S3_SDI_M1 (V2 exchanged) | PWM13_M1 | 3.3V |
| 39 | GND | Ka honua | 0V | |
| 40 | GPIO4_C5_d | UART9_TX_M1/SPI3_MISO_M1 /I2S3_SDO_M1 (V2 exchanged) | PWM12_M1 | 3.3V |
Nānā:
|
||||
Māka Hana Compact3566
Alakaʻi Hoʻolālā Lako
Kaapuni hookui
USB Host
Kaapuni Debug
Kaapuni Headphone
Kaapuni a me LCD
Kaapuni GPIO
Kaapuni POE
PCBA mīkini
Nā hiʻohiʻona uila huahana
ʻO ka hoʻopau ʻana a me ka Mahana
| hōʻailona | ʻĀpana | Min | ʻAno | Max | Unite |
| VCC50_SYS | Mana Nui Voltage |
5-5% |
5 |
5 + 5% | V |
| Isys_in | VCC5V_SYS hoʻokomo i kēia manawa |
820 | mA | ||
| VCC_RTC | RTC Voltage | 1.8 | 3 | 3.4 | V |
| Iirtc | Hoʻokomo RTC ʻO kēia manawa |
5 | 8 | uA | |
| Ta | Ka Mahana Hana | -0 | 70 | °C | |
| ʻO Tstg | Ka Mahana Waihona | -40 | 85 | °C |
Pono o ka ho'āʻo
| Haʻahaʻa wela hana ho'āʻo | ||
| ʻIkepili | Hana 4h ma Haʻahaʻa wela | -20°C±2°C |
| Ka hopena | hala | |
| ʻO ka hoʻāʻo ʻana i ka wela wela | ||
| ʻIkepili | Ke hana nei i 8h i ka wela kiʻekiʻe | 65°C±2°C |
| Ka hopena | hala | |
| Ho'āʻo Ola Ola | ||
| Ke hana nei ma ka lumi | 120h | |
| hala | ||
Palapala / Punawai
 |
Boardcon Embedded Design Compact3566 Embedded Development Board [pdf] Palapala Hoʻohana Compact3566 Papa Hoʻoulu Hoʻohui, Compact3566, Papa Hoʻoulu Hoʻohui, Papa Hoʻoulu, Papa |
