HAMATON NLP2024005 NLP Pro Tesla BLE Sensor

Specifications

• Model: NLP Pro Sensor (Model number: NLP2024005)
• Variants: Flow through sensor, short flex, long flex, Cap sensor
• Recommended Torque: 3N.m
• Recommended Tools: 3N.m standard torque tool, open end wrench No.9 or 10, Special tool developed by Hamaton, Claps

NLP Pro Sensor install General

• For the NLP Pro Sensor (Model number: NLP2024005) installed on trailers/ trucks, the NLP Pro Sensor, which has many variants, such as flow through sensor, short
  flex, long flex, and Cap sensor, it’s best to installit onto the Valve, air tank, or check port of the hose. We recommend using 3N.m torque to the NLP Pro Sensor onto the check port/ valves.

Recommended tools:

• 3N · m standard torque tool. open-end wrench，
• No.9 or 10. A special tool, Hamaton, was developed. Claps

Installation Process:

1. Flow through sensor installation:
   1. Take off the valve cap for the check port or valves.
   2. Use Hamaton socket with torque tool to screw NLP Pro Sensor on the valve.
2. Long and short flex sensor installation:
   1. Take off the valve cap for the original valve.
   2. Mount the clip on the wheel hub.
   3. Screw the sensor on the original valve.
   4. Put the sensor slot into the clip.
3. Cap sensor installation:
   1. Take off the valve cap for the check port.
   2. Fit the cap sensor onto the check port or valves, and pre-twist 2 or 3 turns.
   3. Use a standard 3N.m torque tool to tighten the sensor onto the valve or check port.

FCC STATEMENT:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
   Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an output circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The user who changes or modifications not expressly approved by the party responsible for compliance could void the user`s authority to operate the equipment.

INDUSTY CANADA STATEMENT:

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation of the device. In addition, this device complies with ICES-003 of the Industry Canada (IC) Rules.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Industry Canada licence-exempt RSS standard(s). These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The user who changes or modifications not expressly approved by the party responsible for compliance could void the user`s authority to operate the equipment.

Frequently Asked Questions

Q: What is the recommended torque for installing the NLP Pro Sensor?
A: The recommended torque for installation is 3N.m.

Q: What tools are recommended for installing the NLP Pro Sensor?
A: Recommended tools include a 3N.m standard torque tool, open-end wrench No.9 or 10, a special tool developed by Hamaton, and Claps.

Documents / Resources

HAMATON NLP2024005 NLP Pro Tesla BLE Sensor [pdf] Instructions NLP2024005, NLP2024005 NLP Pro Tesla BLE Sensor, NLP Pro Tesla BLE Sensor, Tesla BLE Sensor, BLE Sensor

References

• User Manual