HAKEN F33 Fan Lamp Remote Controller
Product Information
Specifications:
- Brightness Adjustment: Allows for adjusting the brightness levels of the device.
- Battery: Requires a Switch AAA (1.5V) battery for operation.
Product Usage Instructions
Brightness Adjustment:
To adjust the brightness level, locate the brightness control feature on the device. Use the designated buttons or controls to increase or decrease the brightness according to your preference.
Battery Installation:
- Locate the battery compartment on the device.
- Open the compartment by following the manufacturer’s instructions.
- Insert a single Switch AAA (1.5V) battery into the compartment, ensuring correct polarity.
- Close the compartment securely as per the instructions provided.
OVERVIEW
- Fan On/Off
- Light On/Off
- Fan gear control
- Brightness adjustment
- Fan forward and reverse switching
- Temperature
- Natural wind on/off
- Mute function
Learning method of remote control
Power on the receiver, press the 
key at the emitter at once. The learning is successful when you hear a double beep ringing from the loudspeaker.
- RF wireless digital transmission technology is adopted to realize the one-to-one control, providing a rate of coincident code less than 1000000. The same code number is attached to the back of the emitter and the receiver. It is required to return a pair of the same code number of emitter/receiver to the manufacturer for repair service in case of any damage.
- In a sufficient space, you can use the receiver at any angle, no worrying about the direction.
Notices
- When the emitter is unable to remotely control the receiver, please check whether the switch batteries are in good contact, whether they are fixed properly, and whether they are out of use.
- When the emitter is unable to remotely control the receiver, please check whether there are other remote control products around the space and check whether the keys are pressed down, because the same nature of remote control products may cause interference with each other, resulting in poor receiving effect. Taking away such articles will normalize the remote control function. (The infrared remote controller is not included.)
- Please use this product under the applicable voltage. Too low a voltage will lead to failure of the remote controller to work (Please refer to the product label for the voltage range and related parameters).
- Please take out the batteries if you will not use this product for a long time.
Caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates. Uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference
- This device must accept any interference received, including interference that may cause undesired operation.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
FAQ
Can I make changes or modifications to the device?
It is cautioned that changes or modifications not expressly approved by the responsible party for compliance could void your authority to operate the equipment. Please refrain from making unauthorized modifications to the device.
Documents / Resources
 |
HAKEN F33 Fan Lamp Remote Controller [pdf] User Manual 2BRBN-F33, 2BRBNF33, f33, F33 Fan Lamp Remote Controller, F33, Fan Lamp Remote Controller, Lamp Remote Controller, Remote Controller, Controller |