MOXA ioThinx 4510 Series Advanced Controllers da I-Os Jagoran Shigarwa

IoThinx 4510 na'urar I/O ce ta ci gaba mai ƙima tare da kayan aiki na musamman da ƙirar software wanda ya sa ya dace don aikace-aikacen sayan bayanan masana'antu iri-iri.

Kunshin Dubawa

1 x ioThinx 4510 samfur

1 x jagorar shigarwa mai sauri (an buga)
2 x farantin murfin gefe

Shigarwa

Haɗin Ƙarfin Tsarin
Haɗa tushen wutar lantarki na 12 zuwa 48 VDC zuwa tashar tashar tashar SP + da SP- tashoshi akan ioThinx 4510. Mai haɗin ƙasa na tsarin yana kan bayan naúrar, wanda zai haɗa zuwa dogo na DIN lokacin da aka haɗa samfurin zuwa gare ta. .

Haɗin Wutar Wuta

ioThinx 4510 na iya karɓar ikon filin ta hanyar shigar da wutar lantarki ta 12/24 VDC. Ana iya amfani da ikon filin don samar da wuta don wasu nau'ikan I/O, kamar shigarwar dijital da na'urorin fitarwa na analog.

Haɗa Filin Ƙarfin Wuta

Haɗa fil ɗin Filin () zuwa filin wutar lantarki.

Haɗa zuwa Cibiyar sadarwa

Sadarwar Ethernet
IoThinx 4510 sanye take da tashoshin LAN guda biyu mara sarrafa su (RJ45). Haɗa kebul na cibiyar sadarwa na Ethernet zuwa kowane tashar jiragen ruwa don samar da haɗin Ethernet zuwa naúrar.

Serial Sadarwa

The ioThinx 4510 sanye take da 3-in-1 serial interface, wanda ke goyan bayan 1 RS-232 tashar jiragen ruwa, ko 1 RS-422 tashar jiragen ruwa, ko 2 RS-485 tashar jiragen ruwa. Koma zuwa teburin aikin fil ɗin da ke ƙasa don saita haɗin haɗin kai zuwa naúrar.

GND	GND	OND	S
^–Farashin VIVCI	^–GXU	SID	V
+? VI VG	+CIX2:1	S12: ina	£
^–Farashin VIVCI	^–CIXI	CIX2:1	Z
+ T VIVG	+CIXI	CXI	T
(Zdrid) S8fr-S11	(Id) ZZE17-S11	(Id) ZEZ-SU	NID

45M Module Wiring
Don cikakkun wayoyi na 45M, koma zuwa ioThinx 4510 Jagoran mai amfani akan jami'in Moxa. website.

Shigar da Tsarin akan Rail din DIN

Mataki na 1: Haɗa shirin hawan naúrar zuwa kan dogo na DIN kuma rage faifan bidiyo akan tashar DIN. Ajiye aƙalla 5.5 cm na sarari sama da layin dogo na DIN don tabbatar da cewa akwai isasshen ɗaki don shigar da naúrar.

Mataki 2: Matsa naúrar zuwa layin dogo na DIN har sai faifan hawa ya kama wuri.

Sanya Module 45M akan DIN-Rail

Mataki na 1: Daidaita 45M module gefe da gefe tare da kai/CPU module, tabbatar da cewa na sama da ƙananan dogo sun haɗa tare.

Mataki 2: Daidaita tsarin 45M gefe da gefe tare da kan/CPU module sa'an nan kuma tura 45M module har sai ya taba DIN dogo. Na gaba, yi amfani da ƙarin ƙarfi har sai ƙirar ƙirar ta zana zuwa dogo na DIN.

NOTE Bayan an haɗe ƙirar zuwa layin dogo na DIN, za a kafa haɗin haɗin kai zuwa bas na ciki.

Cire Module 45M daga DIN Rail

Mataki 1: Yi amfani da yatsanka don ɗaga shafin sakin a ƙananan ɓangaren tsarin.

Mataki 2: Danna saman shafin sakin don manne shi, sannan a ciro tsarin.

NOTE Haɗin wutar lantarki don motar bas ta ciki za a katse lokacin cire ƙirar 45M.

GARGADI
Tabbatar cewa wutar tana kashe kafin cire kayayyaki don guje wa lalata kayan aiki.

Shigar da Rufin akan Module na Farko da na Ƙarshe

Haɗa murfin zuwa na farko da na ƙarshe don rufe lambobin sadarwa na modules.

SANARWA
Tabbatar haɗa murfin don samar da kariya ta fitarwa na lantarki.

Shigarwa a kwance

Kafin shigar da na'urar, tabbatar da akwai isasshen sarari tsakanin na'urar da abubuwan da ke kusa (bango, wasu na'urori, da sauransu) don tabbatar da zubar da zafi mai kyau. Don tabbatar da cewa na'urar tana aiki da kyau, muna ba da shawarar tanadin adadin sararin da aka nuna a cikin adadi kusa.

HANKALI
KAR KA shigar da na'urar a tsaye. Idan an shigar da na'urar a tsaye, ƙirar ɓarkewar zafi ba za ta yi kamar yadda aka yi niyya ba.

LED Manuniya

Suna	Nuni	LED Qty	Bayani
SP	Ƙarfin tsarin	1	Kunnawa: Powerara a Kashe: Kashe wuta
FP	Ikon filin	1	Kunnawa: Powerara a Kashe: Kashe wuta
RDY	Tsarin (Kernel) Shirye	1	Green: A shirye tsarin Green Slow Blinking: Booting up Red: Kuskuren tsari Jan Slow Kiftawa: Loading Tsoffin Factory farfadowa da na'ura / Haɓaka firmware/Ajiyayyen yanayin Red Fast Blinking: Yanayin lafiya A kashe: A kashe wuta
LAN	Haɗin Ethernet	1 ga kowane tashar jiragen ruwa	Green: Haɗin 100Mb Amber: Haɗin 10Mb Blinking: Kashe bayanai: Kashe
Px	Serial Connection	1 ga kowane tashar jiragen ruwa	Green: Tx Farashin: Rx Kiftawar da ba a lokaci guda ba: watsa bayanai A kashe: An cire haɗin

Tsarin Tsari

Kanfigareshan ta hanyar Web Console
Babban tsarin naúrar ana yin ta ta hanyar web wasan bidiyo.
• Adireshin IP na asali: 192.168.127.254
• Mashin Subnet: 255.255.255.0
NOTE Tabbatar da saita adireshin IP na PC ɗin mai masaukin don amfani da rukunin yanar gizo iri ɗaya da naúrar. Domin misaliampku, 192.168.127.253
IOxpress Utility
IOxpress kayan aiki ne wanda ke taimakawa masu amfani tare da yawan turawa, nema, da gano raka'a akan hanyar sadarwar gida. Ana iya sauke wannan kayan aiki daga Moxa's website.
Ana Load da Tsoffin Saitunan Factory
Akwai hanyoyi guda uku don mayar da naúrar zuwa saitunan masana'anta:
a. Riƙe maɓallin Sake saitin a cikin ƙofar gaban naúrar na tsawon daƙiƙa 10 yayin da ake kunna ta.
b. Zaɓi sashin daga shafin Laburaren Na'ura na na'urar mai amfani, sannan zaɓi Default Factory Load.
c. Jeka shafin System akan naúrar web console kuma zaɓi Load
Default Factory a cikin Kanfigareshan sashe.
NOTE Da fatan za a koma zuwa littafin jagorar mai amfani don bayani kan cikakken tsari da saituna.

Yadda ake Sauke Software

Ana iya sauke fakitin software masu alaƙa daga Moxa website.
Mataki na 1: Je zuwa adireshin da ke gaba:
https://www.moxa.com/en/support
Mataki na 2: Rubuta sunan samfurin a cikin akwatin bincike ko zaɓi samfur daga cikin akwatin da aka saukar sannan danna Bincike.
Ana amfani da jerin ioLogik E1200 don tsohonamples kasa.

Mataki na 3: Jeka shafin software don zazzage sabuwar software don samfurin.

Ƙayyadaddun bayanai

Shigar da Yanzu	800 mA 0 12 VDC
Shigar da Voltage	12 zuwa 48 VDC Wurin Wuta: 12/24 VDC
Yanayin Aiki	Daidaitaccen Samfura: -20 zuwa 60°C (-4 zuwa 140°F) Faɗin zafin jiki. Samfura: -40 zuwa 75°C (-40 zuwa 167°F)
Ajiya Zazzabi	-40 zuwa 85°C (-40 zuwa 185°F)

Hankali

Wannan na'urar an yi amfani da ita ne kawai a cikin gida a wuraren da ke da digiri na 2.
Wannan na'urar tana da filin wutar lantarki da fitilun ƙasa biyu a bayan na'urar. Don ƙarin kariya, haɗa fil ɗin ikon filin zuwa filin wutar lantarki kuma haɗa layin dogo na DIN zuwa ƙasan ƙasa.

Dole ne a yi amfani da igiyoyi da aka ƙididdige mafi ƙarancin zafin jiki na 105 ° C don Tashar Kawo Wuta.
Muna ba da shawarar amfani da nau'ikan kebul masu zuwa don wayoyi:
IoThinx 4510 Jerin:
> AWG 12 zuwa 16 don haɗin wutar lantarki
> AWG 16 zuwa 28 don haɗin kai
• 45MR-7210:
> AWG 12 zuwa 16 don haɗin wutar lantarki
• 45MR-2600/2601/2606 Tashar Fitar Dijital:
> AWG 16 zuwa 18
• 45MR-2404 Relay Output Terminal:
> AWG 16 zuwa 18
• Duk sauran kayan aikin 45MR:
> AWG 16 zuwa 24

Takardu / Albarkatu

MOXA ioThinx 4510 Series Advanced Controllers da I-Os [pdf] Jagoran Shigarwa
ioThinx 4510 Series Advanced Controllers da I-Os

Magana

Manual mai amfani

Gabatarwa