FLYSKY FRM303 Multi-Ayyukan Babban Ayyukan RF Module Umarnin Jagora

Gabatarwa

FRM303 babban aikin RF ne na ayyuka da yawa bisa yarda da ka'idar tsarin dijital ta AFHDS 3 tsara ta uku ta atomatik. Yana fasalta eriya ɗaya mai maye gurbin waje, goyan bayan watsawa biyu, hanyoyin samar da wutar lantarki guda uku, goyan bayan voltage aikin ƙararrawa idan akwai wutar lantarki ta waje, da goyan bayan shigar da siginar PPM, S.BUS da UART. A cikin sigina na PPM da S.BUS, yana goyan bayan saitunan ɗauri, sauyawa samfuri (bincike ta atomatik na mai karɓa), saitin ƙa'idar ƙirar mai karɓa da rashin tsaro.

Ƙarsheview

1. SMA Antenna Connector
2. Nau'in-C USB Port
3. LED
4. Maɓallin Hanya Biyar
5. Maɓallin Wuta uku (Int/Kashe/Ext)
6. Siginar Siginiya
7. Interface Mai Bayar da Wuta ta XT30(Ext)
8. Wurin Ramin Adafta
9. Screw Holes don Gyara Adafta(M2)

FGPZ01 adaftar Mai jituwa tare da PL18

1. Matsakaicin ramukan don Gyara adaftar FGPZ01 da TX(M3)
2. Skru don Gyara adaftar FGPZ01 da Module RF
3. Mai Haɗin RF na Adaftar FGPZ01
4. Kebul don Haɗa Adaftar FGPZ01 da Module RF
5. M3 Screws don Gyara adaftar FGPZ01 zuwa TX
6. Saukewa: FGPZ01

Adaftar FGPZ02 Mai jituwa tare da Module na JR RF

1. Solts don Gyara adaftar FGPZ02
2. Saukewa: FGPZ02
3. Mai Haɗin RF na Adaftar FGPZ02
4. Kebul don Haɗa Adaftar FGPZ02 da Module RF
5. M2 Screws don Gyara adaftar FGPZ02 zuwa Module RF

Adaftar FGPZ03 Mai jituwa tare da Module na Stealth I/O

1. Solts na FGPZ03 Adafta don Gyara Module RF
2. Saukewa: FGPZ03
3. Mai Haɗin RF na Adaftar FGPZ03
4. Kebul don Haɗa Adaftar FGPZ03 da Module RF
5. Sukurori don Gyara adaftar FGPZ03 zuwa TX

Yawancin igiyoyi masu haɗa siginar siginar na FRM303

1. Don Haɗa Interface Siginar Module FRM303 RF
2. FUTABA Trainer Interface(FS-XC501 Cable)
3. Interface Mai Haɗin Tasha S (FS-XC502 Cable)
4. 3.5MM Audio Head (FS-XC503 Cable)
5. Interface Servo (FS-XC504 Cable)
6. DIY Interface (FS-XC505 Cable)
7. Don Haɗa zuwa Interface XT30 na FRM303
8. Interface Baturi (FS-XC601 Cable)

Adaftar Antenna SMA
Lura: Idan yana da wahala a shigar da eriya saboda tsarin watsawa, zaku iya amfani da wannan adaftar eriya ta SMA don sanya shigarwar eriya ta fi dacewa.

1. Adaftar Eriya na 45-digiri SMA
2. SMA Eriya Kariya Cap
3. FS-FRA01 2.4G Eriya
4. Dutsen Aid Ratchet

Ƙayyadaddun bayanai

• Sunan samfur: Saukewa: FRM303
• Na'urorin daidaitawa: PPM: Na'urorin da za su iya fitar da daidaitattun siginar PPM, kamar FS-TH9X, FS-ST8, FTr8B mai karɓar; S.BUS: Na'urorin da za su iya fitar da daidaitattun siginar S.BUS, irin su FS-ST8, FTr8B mai karɓa; Rufe Tushen yarjejeniya-1.5M UART: PL18; Buɗe tushen yarjejeniya-1.5M UART: EL18; Bude tushen yarjejeniya-115200 UART: Na'urorin da za su iya fitar da bude tushen yarjejeniya-115200 UART siginar.
• Samfuran Daidaitawa: Kafaffen jirgin sama, jirage marasa matuki, relays, da sauransu.
• Adadin Tashoshi: 18
• Ƙaddamarwa: 4096
• RF: 2.4 GHz ISM
• 2.4G ProtocolSaukewa: AFHDS3
• Matsakaicin ƙarfi:<20dBm (eirp) (EU)
• Nisa: > 3500m (Nisan iska ba tare da tsangwama ba)
• Eriya: Eriya ta SMA na waje (Filin-screw-inner-pin)
• Ƙarfin shigarwa: XT30 Interfac: 5 ~ 28V / DC Interface Interface: 5 ~ 10V / DC tashar USB: 4.5 ~ 5.5V/DC
• Tashar USB: 4.5 ~ 5.5V / DC
• Aiki Yanzu: 98mA / 8.4V (Wurin wutar lantarki) 138mA / 5.8V
• Bayanin Bayani: PPM, UART da S.BUS
• Matsayin Zazzabi: -10 ℃ ~ +60 ℃
• Tashin hankali: 20% ~ 95%
• Sabunta Kan layi: Ee
• Girma: 75*44*15.5mm(ban da eriya)
• Nauyi: 65g (ban da eriya da adaftar)
• Takaddun shaida: CE, FCC ID:2A2UNFRM30300

Ayyuka na asali

Gabatarwa zuwa Sauyawa da Maɓallai
Maɓallin wutar lantarki mai matsayi uku: Wannan jujjuya yana ba ku damar canza hanyar samar da wutar lantarki ta tsarin RF: wutar lantarki ta ciki (Int), kashe wuta (Kashe), da wutar lantarki ta waje (Ext). Ana samun wutar lantarki ta waje ta hanyar XT30.

Maɓallin hanya biyar: Sama, Ƙasa, Hagu, Dama da tsakiya.
An kwatanta ayyukan maɓallin hanya biyar a ƙasa. Ya kamata a lura cewa maɓalli ba ya aiki lokacin da aka gane siginar shigarwa azaman siginar serial.

Lura: A cikin maɓalli na ayyuka, idan kun ji "Danna", yana nuna cewa aikin yana da inganci. Kuma aikin maɓalli ba ya zagaye

Samar da Wutar Lantarki na Module RF 

Za'a iya kunna tsarin RF ɗin ta hanyoyi guda uku: Nau'in-C interface, da wutar lantarki ta ciki ko XT-30 na waje.

• Ƙarfafawa ta hanyar ƙirar Type-C shine fifiko na farko. A cikin wutar lantarki ta hanyar sadarwa na Type-C, RF module baya kashe lokacin da kuka canza wuta idan akwai wutar lantarki ta ciki ko wutar lantarki ta waje.
• A cikin wutar lantarki na ciki ko wutar lantarki ta waje (maimakon samar da wutar lantarki ta hanyar dubawar Type-C), tsarin RF zai sake farawa lokacin da kuka canza wutar.

Lokacin da kake sarrafa na'ura daga nesa, don Allah kar a yi amfani da nau'in-C don samar da wuta ga tsarin RF don gujewa rasa ikon na'urar. Lokacin da tsarin RF ke aiki ta hanyar sadarwa ta Type-C, ƙirar RF za ta rage ƙarfin fitarwa ta atomatik don guje wa lalacewar kebul na na'urar da aka haɗa. Bayan an rage wutar lantarki, za a gajarta nesa da nesa.

Ƙarar Wajetage Ƙararrawa 

Lokacin da tsarin RF ke aiki da baturin lithium da aka haɗa ta hanyar sadarwa ta XT-30 na dogon lokaci, vol.tagAyyukan ƙararrawa da aka bayar a cikin tsarin RF zai tunatar da ku maye gurbin baturin cikin lokaci. Lokacin da tsarin RF ya kunna, tsarin yana gano wutar lantarki ta atomatik voltage kuma yana gano adadin sassan baturi da ƙararrawa voltage darajar bisa ga voltage. Lokacin da tsarin ya gano cewa baturin voltage ya yi ƙasa da ƙimar ƙararrawa daidai, zai ba da rahoton ƙararrawa. Takamammen tebur shine kamar haka.

 

Gano Voltage	Gano Yawan Sassan Baturi	Ƙararrawa mai dacewa
≤ 6V> 6V da ≤ 9V	1S lithium baturi2S lithium baturi	3.65V 7.3V
> 9V da ≤ 13.5V	3S lithium baturi	11V
> 13.5V da ≤ 17.6V	4S lithium baturi	14.5V
> 17.6V da ≤ 21.3V	5S lithium baturi	18.2V
> 21.3V	6S lithium baturi	22V

Ƙararrawa Mai Girma
Zazzabi na ƙirar RF na iya tashi saboda yanayin amfani ko aiki na tsawon lokaci. Lokacin da tsarin ya gano zafin jiki na ciki ≥ 60 ℃, zai ba da ƙararrawa mai ji. Idan samfurin sarrafawa yana cikin iska a wannan lokacin, da fatan za a kashe tsarin RF bayan dawowar. Kuna iya sake amfani da samfurin bayan ya huce.

Ƙararrawar Siginar Ƙararrawa
Lokacin da tsarin ya gano cewa ƙimar ƙarfin siginar da aka karɓa ta yi ƙasa da ƙimar da aka saita, tsarin zai ba da ƙararrawa mai ji.

Sabunta Firmware
Za a iya haɗa tsarin RF ɗin zuwa PC ta hanyar nau'in-C don sabunta firmware ta FlySky Assistant. Jihohin da suka dace na LED mai walƙiya a cikin tsarin sabuntawa an kwatanta su a cikin tebur mai zuwa. Matakan sabunta su ne kamar haka:

1. A gefen PC, bayan zazzage sabuwar FlySkyAssistant V3.0.4 ko kuma daga baya firmware, sannan fara shi.
2. Bayan haɗa tsarin RF zuwa PC tare da kebul na Type-C, gama sabuntawa ta FlySkyAssistant.

Launi na LED	Jihar LED	Jiha Module RF daidai
RedRed	Biyu-flash-daya-kashe Uku-flash-daya-kashe (Fast)	Wfoarciteidngufpodrafitremswtaatere haɓakawa ko cikin Ana ɗaukaka firmware mai karɓa
Yellow	Uku-flash-daya-kashe (Fast)	Ana ɗaukaka firmware na RF module

Idan ba za ku iya sabunta firmware na RF ta matakan da ke sama ba, kuna buƙatar sabunta shi bayan yana cikin yanayin sabuntawar tilastawa. Bayan haka, kammala sabuntawa ta bin matakan sabunta firmware. Matakan sune kamar haka: Danna maɓallin sama sama sama da 9S yayin da ake kunna tsarin RF. Jajayen LED yana cikin yanayi mai walƙiya-daya-kashe, wato, yana shiga yanayin sabuntawar tilastawa.

Maida Jihar Saitin Factory
Mayar da tsarin RF zuwa yanayin tsohuwar masana'anta. Matakan saitin sune kamar haka:
Danna ko tura ƙasa da maɓallin ƙasa akan 3S kuma a halin yanzu kunna shi. LED ɗin yana da ƙarfi a cikin ja. Bayan haka, tsarin RF yana cikin yanayin gano siginar shigarwa, LED yana ja tare da ON don 2S da KASHE don 3S.

Saitunan Siginar shigarwa
FRM303 yana goyan bayan sauyawa tsakanin sigina na serial, siginar PPM da siginar S.BUS. Matakan saitin sune kamar haka:

1. Maɓallin sama sama don ≥ 3S da <9S yayin da ake yin ƙarfi akan tsarin RF, yana shiga yanayin saitin siginar shigarwa. Yanzu LED a blue yana kunne.
2. Danna sama maɓallin sama ko tura ƙasa maɓallin ƙasa don canza siginar shigarwa. Jihohin masu walƙiya na LED sun bambanta da sigina kamar yadda aka nuna a teburin da ke ƙasa.
3. Danna maɓallin tsakiya don 3S don ajiye saitunan. Danna maɓallin Hagu don fita yanayin saitin sigina.

Launi na LED	Jihar LED	Siginar shigar da ta dace
Blue	Fila ɗaya-ɗaya-kashe	PPM
Blue	Biyu-fila-daya-kashe	S.BUS
Blue	Uku-fila-daya-kashe	Ƙa'idar Tushen Rufe-1.5M UART(Tsoffin)
Blue	Hudu-fila-daya-kashe	Open Source Protocol-1.5M UART
Blue	Fila biyar-daya-kashe	Bude tushen yarjejeniya-115200 UART

Bayanan kula:

1. Saita siginar shigarwar zuwa Ka'idar Rufewar-1.5M UART, lokacin da ake amfani da mai watsawa PL18.
2. Koma da takaddun na'urar watsawa masu dacewa don saitin da ke da alaƙa, lokacin da aka saita Open Source Protocol-1.5M UART ko Open source Protocol-115200 UART.
3. Lokacin da aka saita PPM ko S.BUS, koma zuwa Sashen Ayyukan Samfura(PPM ko S.BUS) don saiti masu alaƙa.
4. Lokacin da aka saita PPM, zai iya goyan bayan siginar PPM maras kyau tare da lokacin sigina na 12.5 ~ 32ms, adadin tashoshi yana cikin kewayon 4 ~ 18, kuma farkon ganewar asali shine 350-450us. Don guje wa kurakuran gano PPM ta atomatik, gano halayen sigina yana iyakance, kuma alamun PPM waɗanda suka wuce halayen da ke sama ba a gane su ba.

Ƙirar siginar shigarwa
Ana amfani da shi don yin hukunci ko tsarin RF yana karɓar tushen siginar da ta dace bayan saita siginar shigarwa. Bayan saita siginar shigarwa ko ba tare da danna maɓalli ba (ko danna maɓallin don <3S) don kunna tsarin RF, sannan zai shigar da yanayin gano siginar shigarwa. LED yana da ja tare da ON don 2S da KASHE don 3S. Kuma jihohin LED masu walƙiya sun bambanta da sigina kamar yadda aka nuna a cikin tebur da ke ƙasa.

Launi na LED	Jihar LED	Jiha Module RF daidai
Ja	ON don 2S kuma KASHE don 3S	A cikin shigar da yanayin gano siginar (rashin shigar siginar shigarwa)
Blue	walƙiya (hankali)	Daidaiton siginar shigarwa

Gabatarwa zuwa RF na yau da kullun aiki
Lokacin da tsarin RF ya gane siginar shigarwa, ya shiga yanayin aiki na yau da kullun. Jihohin LED sun yi daidai da jahohin ƙirar RF daban-daban kamar yadda aka nuna a ƙasa.

Launi na LED	Jihar LED	Jiha Module RF daidai
Kore	M a kunne	Sadarwa ta al'ada tare da mai karɓa a ciki yanayin hanya biyu
Blue	walƙiya (hankali)	Babu sadarwa tare da mai karɓa ta hanya ɗaya ko ta hanya biyu
Blue	ON don 2S kuma KASHE don 3S	Sigina mara kyau bayan siginar shigarwar nasara ganewa
Ja/Kore/Blue	walƙiya (hankali)	Yanayin ƙararrawa

Ayyukan samfuri (PPM ko S.BUS)

Wannan sashe yana gabatar da saitunan ƙira don siginar S.BUS ko PPM a cikin ayyukan yau da kullun na tsarin FRM303 RF. Hanyoyin saiti don S.BUS ko siginar PPM iri ɗaya ne. Ɗauki siginar PPM a matsayin misali. Ya kamata a lura cewa ya kamata a saita siginar shigarwar FRM303 zuwa PPM kuma a saita nau'in RF na mai watsawa zuwa PPM.

Canja Model RF da Neman Mai karɓa ta atomatik
Idan siginonin shigarwa sune PPM da S.BUS, wannan ƙirar RF tana ba da jimlar ƙungiyoyin ƙira 10. Za a adana bayanan da ke da alaƙa da ƙirar a cikin ƙirar, kamar saitin RF, ID na mai karɓa bayan ɗaure ta hanyoyi biyu, saitunan rashin aminci, da ƙa'idar mu'amala ta RX. Matakan saitin sune kamar haka:

1. Danna ko danna maɓallin Dama don 3S. Bayan "danna", LED ɗin yana haskakawa da fari. Yana shiga yanayin saitin sauya ƙirar RF. Jihohin walƙiya na LED sun bambanta da ƙira, duba teburin da ke ƙasa.
2. Danna sama maɓallin sama ko tura ƙasa maɓallin ƙasa don zaɓar samfurin da ya dace.
3. Danna maɓallin tsakiya don 3S don ajiye saitunan. Danna maɓallin Hagu zuwa hagu don fita yanayin sauya samfurin.

Launi na LED	Jihar LED	Samfura
WhiteWhite	Fila daya-daya-kashe Biyu-fila-daya-kashe	Farashin RF 1RF 2
Fari	Uku-fila-daya-kashe	Farashin RF3
Fari	Hudu-fila-daya-kashe	Farashin RF4
Fari	Fila biyar-daya-kashe	Farashin RF5
Fari & Blue	Fari: Daya-fila-daya-kashe; Blue: Fita ɗaya-ɗaya-kashe	Farashin RF6
Fari & Blue	Fari: Biyu-fila-daya-kashe; Blue: Fita ɗaya-ɗaya-kashe	Farashin RF7
Fari & Blue	Fari: Uku-flash-daya-kashe; Blue: Fita ɗaya-ɗaya-kashe	Farashin RF8
Fari & Blue	Fari: Hudu-flash-daya-kashe; Blue: Fita ɗaya-ɗaya-kashe	Farashin RF9
Fari & Blue	Fari: Biyar-fila-daya-kashe; Blue: Fita ɗaya-ɗaya-kashe	Farashin RF10

Bayan haɗakarwa ta hanyoyi biyu tsakanin samfurin da mai karɓa, za ka iya sauri nemo samfurin da aka ɗaure tare da mai karɓa ta hanyar wannan aikin. Yana iya fita ta atomatik bayan wurin da aka yi nasara, kuma ya ci gaba da sadarwa ta al'ada tare da mai karɓa. Matakan binciken sune kamar haka:

1. A cikin yanayin sauya samfurin, danna maɓallin Dama don shigar da yanayin neman mai karɓa. A wannan lokacin, LED ɗin shuɗi ne tare da walƙiya mai sauri.
2. Ana kunna mai karɓa kuma binciken ya yi nasara. Sannan yana fita ta atomatik daga yanayin bincike. A wannan lokacin, LED yana da ƙarfi a cikin kore.

Bayanan kula:

1. Idan akwai hanyar sadarwa ta hanya ɗaya tsakanin mai karɓa da tsarin RF, ba a tallafawa binciken mai karɓa ta atomatik.
2. Binciken yana farawa daga samfurin inda yake a halin yanzu, don canzawa ta atomatik zuwa samfurin na gaba. Idan ba'a samo shi ba, akwai bincike na keke-da-keke har sai kun danna maɓallin Hagu da hannu don fita yanayin bincike.

Saita Tsarin RF da Binding

Saita tsarin RF da ɗaure. Bayan an saita tsarin RF, tsarin FRM303 RF zai iya aiwatar da ɗaurin hanya ɗaya ko ta biyu tare da mai karɓa wanda ya dace da shi. Ɗauki ɗaurin hanyoyi biyu a matsayin tsohonample. Matakan saitin sune kamar haka:

1. Latsa maɓallin tsakiya don 3S. Bayan "danna", LED ɗin yana haskakawa a cikin magenta. Jihohin walƙiya na LED sun bambanta da tsarin RF, duba teburin da ke ƙasa. Danna sama maɓallin sama ko tura ƙasa maɓallin ƙasa don zaɓar tsarin RF mai dacewa.
2. Danna maɓallin Dama dama. LED ɗin yana walƙiya da sauri kore. Tsarin RF yana shiga yanayin ɗauri. Danna maɓallin Hagu zuwa hagu don fita yanayin ɗaure.
3. Sanya mai karɓa ya shigar da yanayin ɗauri.
4. Bayan dauri mai nasara, tsarin RF yana fita ta atomatik daga yanayin ɗaurin.

Lura: Idan tsarin RF ɗin zai ɗaure tare da mai karɓa a cikin yanayin hanya ɗaya, lokacin da mai karɓar LED ya zama jinkirin walƙiya daga walƙiya mai sauri, yana nuna ɗaurin ya yi nasara. Danna maɓallin Hagu zuwa hagu don fita yanayin ɗaure.

LED launi	Jihar LED	Daidaitaccen Tsarin RF
Magenta	Fila ɗaya-daya-na	Classic 18CH ta hanyoyi biyu
Magenta	Biyu-fila-daya-kashe	Classic 18CH ta hanya ɗaya
Magenta	Uku-flash-daya-na	Na yau da kullun 18CH ta hanyoyi biyu
Magenta	Hudu-fila-daya-na	Na yau da kullun 18CH ta hanyoyi biyu

Saita Ra'ayin Interface RX
Saita ƙa'idar mu'amalar mai karɓa. LED shine cyan a cikin wannan yanayin. Matakan saitin sune kamar haka:

1. Danna ko tura hagu maɓallin Hagu don 3S. Bayan "danna", LED ɗin yana haskakawa a cikin cyan. Yana shiga yanayin saitin ƙa'idar dubawa ta RX. Jihohin walƙiya na LED sun bambanta da ƙa'idodi, duba teburin da ke ƙasa.
2. Danna sama maɓallin sama ko tura ƙasa maɓallin ƙasa don zaɓar ƙa'idar da ta dace.
3. Danna maɓallin tsakiya don 3S don ajiye saitunan. Danna maɓallin Hagu zuwa hagu don fita yanayin saitin yarjejeniya.

Launi na LED	Jihar LED	Madaidaicin yarjejeniya ta Interface RX
CyanCyan	Fila daya-daya-kashe Biyu-fila-daya-kashe	PWMi-BUS ya fita
CyanCyan	Uku-fila-daya-kashe-hudu-fila-daya-kashe	S.BUS PPM
Cyan	Hudu-fila-daya-kashe	S.BUS PPM

Lura: A cikin yanayin hanya biyu, ko da kuwa an kunna mai karɓa, wannan saitin na iya yin nasara. A cikin yanayin hanya ɗaya, wannan saitin zai iya yin tasiri kawai idan an sake ɗaure tare da mai karɓa.

Zabin	Classic masu karɓa dubawa guda ɗaya kawai za a iya saita tare da Interface yarjejeniya, don example, FTr4, FGr4P da FGr4s.	Classic masu karɓa musaya guda biyu kawai za a iya saita tare da Interface Protocol, domin misaliample, FTr16S, FGr4 da FTr10.	Ingantattun masu karɓa ingantattun masu karɓa kamar FTr12B da FTr8B tare da Newport Interface NPA, NPB, da dai sauransu.
PWM	Farashin CH1 fitar da PWM, da i-BUS dubawa fitar da i-BUS	Farashin CH1 fitar da PWM, da i-BUS dubawa fitar da i-BUS.	Farashin NPA yana fitar da PWM, sauran Newport dubawa Farashin PWM.
i-BUS fita	Farashin CH1 fitar da PPM, da i-BUS dubawa fitar da i-BUS.	Farashin CH1 fitar da PPM, da i-BUS dubawa fitar da i-BUS.	Farashin NPA Outputsi-BUS fita, da sauran Newport interface Farashin PWM.
S.BUS	Farashin CH1 fitar da PWM, da i-BUS dubawa Rahoton da aka ƙayyade na S.BUS.	Farashin CH1 fitar da PWM, da i-BUS dubawa Rahoton da aka ƙayyade na S.BUS	Farashin NPA fitar da S.BUS, da sauran Newport interface Farashin PWM.
PPM	Farashin CH1 fitar da PPM, da i-BUS dubawa Rahoton da aka ƙayyade na S.BUS.	Farashin CH1 fitar da PPM, da i-BUS dubawa Rahoton da aka ƙayyade na S.BUS.	Farashin NPA yana fitar da PPM, sauran Newport dubawa Farashin PWM.

Saitin Failsafe
Saita rashin lafiya. Akwai zaɓuɓɓuka guda uku waɗanda za a iya saita: Babu fitarwa, Kyauta da Kafaffen ƙima. Matakan saitin sune kamar haka:

1. Danna maɓallin ƙasa don 3S. Bayan "danna", LED ɗin yana haskakawa da ja. Jihohin walƙiya na LED sun bambanta tare da saitin Failsafe, duba teburin da ke ƙasa.
2. Danna sama maɓallin sama ko tura ƙasa maɓallin ƙasa don zaɓar abin da ya dace.
3. Danna maɓallin tsakiya don 3S don ajiye saitunan. Danna maɓallin Hagu zuwa hagu don fita yanayin saitin rashin aminci.

Launi na LED	Jihar LED	Daidaitaccen Saitin Saitin Rashin Safe
Ja	Fila ɗaya-ɗaya-kashe	Babu fitarwa ga duk tashoshi
RedRed	Biyu-flash-daya-kashe Uku-flash-daya-kashe	Afillcsahfaen. nels suna ci gaba da fitarwa na ƙarshe kafin ƙimar tashar fitarwa na yanzu shine ƙimar amincin kowane tashoshi.

Fitar Ƙarfin Sigina
Wannan tsarin RF yana goyan bayan fitowar ƙarfin sigina. Ta hanyar tsoho, ba a ba da izinin kunna kashewa ba. CH14 yana fitar da ƙarfin siginar, maimakon bayanan tashar da mai watsawa ya aiko.

Gyaran Wuta
Ana iya daidaita ƙarfin FRM303 tsakanin 14dBm ~ 33dBm (25mW ~ 2W). Ƙarfin da aka daidaita shine 25mW (14dBm), 100Mw (20dBm), 500Mw (27dBm), 1W (30dBm) ko 2W (33dBm). Da fatan za a kula da wutar lantarki na iya bambanta da yanayin samar da wutar lantarki daban-daban. Ana iya daidaita wutar lantarki har zuwa 2W (33dBm) lokacin da aka haɗa wutar lantarki ta waje, har zuwa 25mW (14dBm) don samar da wutar lantarki na USB, har zuwa 500mW (27dBm) don samar da wutar lantarki na ciki.

Matakan saitin sune kamar haka:

1. Danna maɓallin Up don 3S. Bayan "danna", LED ɗin yana haskakawa cikin rawaya. Yana shiga yanayin daidaita wutar lantarki. Jihohin filasha na LED sun bambanta da jihohi, duba teburin da ke ƙasa.
2. Danna sama maɓallin sama ko tura ƙasa maɓallin ƙasa don zaɓar ƙarfin da ya dace.
3. Danna maɓallin tsakiya don 3S don ajiye saitunan. Danna maɓallin Hagu zuwa hagu don fita yanayin da aka daidaita wutar lantarki.

Launi na LED	Jihar LED	Ƙarfin da ya dace
Yellow	Fila ɗaya-ɗaya-kashe	25mW (14dBm)
Yellow	Biyu-fila-daya-kashe	100mW (20dBm)
Yellow	Uku-fila-daya-kashe	500mW (27dBm)
Yellow	Hudu-fila-daya-kashe	1W (30dBm)
Yellow	Fila biyar-daya-kashe	2W (33dBm)

Lura: Akwai nau'i biyu da aka ɗora a cikin website. Ana iya daidaita wutar har zuwa 1W(30dBm) don sigar FCC, kuma har zuwa 2W(33dBm) don sigar Haɓaka. Da fatan za a sauke sigar da ta dace bisa ga abin da ake bukata.

Hankali

• Tabbatar an shigar da tsarin RF kuma an daidaita shi daidai, rashin yin hakan na iya haifar da mummunan rauni.
• Rike eriyar RF aƙalla 1cm nesa da kayan aiki kamar carbon ko ƙarfe.
• Don tabbatar da ingancin sigina mai kyau, kar a riƙe eriyar RF yayin amfani.
• Karka kunna mai karɓa yayin aiwatar da saitin don hana asarar sarrafawa.
• Tabbatar kasancewa cikin kewayon don hana asarar sarrafawa.
• Ana ba da shawarar cewa a yi amfani da wutar lantarki ta waje don tabbatar da cewa tsarin RF yana samun isasshen ƙarfin aiki daidai.
• Lokacin da ba a amfani da tsarin RF, da fatan za a juya wutar lantarki zuwa matsayin KASHE. Idan ba a yi amfani da shi na dogon lokaci ba, da fatan za a kashe shi. Ko da ƙaramin halin yanzu na iya haifar da lalacewa ga baturin RF ɗin.
• Ba a yarda a yi amfani da Nau'in-C don ba da wutar lantarki ga tsarin RF lokacin da samfurin jirgin ke cikin tashi don guje wa yanayin haɗari.

Takaddun shaida

Bayanin Yarda da FCC
Wannan na'urar ta bi Sashe na 15 na Dokokin FCC. Aiki yana ƙarƙashin sharuɗɗa biyu masu zuwa: (1) wannan na'urar bazai haifar da tsangwama mai cutarwa ba, kuma (2) dole ne wannan na'urar ta karɓi duk wani tsangwama da aka karɓa, gami da tsangwama wanda zai iya haifar da aiki maras so. Gargaɗi: canje-canje ko gyare-gyaren da ƙungiyar da ke da alhakin bin doka ba ta amince da su ba na iya ɓata ikon mai amfani na sarrafa kayan aiki. An gwada wannan kayan aikin kuma an same shi don yin aiki da iyaka don na'urar dijital ta Class B, bisa ga Sashe na 15 na Dokokin FCC. An ƙirƙira waɗannan iyakokin don ba da kariya mai ma'ana daga tsangwama mai cutarwa a cikin shigarwar mazauni. Wannan kayan aiki yana haifarwa, yana amfani da kuma zai iya haskaka ƙarfin mitar rediyo kuma, idan ba'a shigar da shi ba kuma ana amfani dashi daidai da umarnin, yana iya haifar da tsangwama mai cutarwa ga sadarwar rediyo. Duk da haka, babu tabbacin cewa tsangwama ba zai faru a cikin wani shigarwa na musamman ba. Idan wannan kayan aikin ya haifar da tsangwama mai cutarwa ga liyafar rediyo ko talabijin, wanda za'a iya tantancewa ta hanyar kashe kayan aiki da kunnawa, ana ƙarfafa mai amfani da yayi ƙoƙarin gyara tsangwama ta hanyar ɗaya ko fiye na waɗannan matakan:

• Sake daidaitawa ko matsar da eriya mai karɓa.
• Ƙara rabuwa tsakanin kayan aiki da mai karɓa.
• Haɗa kayan aiki zuwa wani mashigar da ke kewaye daban da wanda aka haɗa mai karɓa zuwa gare shi.
• Tuntuɓi dila ko gogaggen masanin rediyo/TV don taimako.

Sanarwar DoC ta EU
Ta haka, [Flysky Technology co., ltd] ya bayyana cewa Kayan aikin Rediyo [FRM303] ya dace da RED 2014/53/EU. Ana samun cikakken rubutun DoC na EU a adireshin intanet mai zuwa: www.flyskytech.com/info_detail/10.html

Yarda da Fitar RF
An kimanta na'urar don biyan buƙatun fiddawa na RF gabaɗaya Ana iya amfani da na'urar a yanayin ɗaukar hoto ba tare da takura ba.

zubar da muhalli
Kada a zubar da tsoffin kayan lantarki tare da ragowar sharar, amma dole ne a zubar da su daban. Ana zubar da shi a wurin tattara jama'a ta hanyar masu zaman kansu kyauta ne. Mai tsofaffin na'urori ne ke da alhakin kawo na'urorin zuwa waɗannan wuraren tattarawa ko kuma wuraren tarawa makamantan haka. Tare da wannan ɗan ƙoƙari na sirri, kuna ba da gudummawa don sake sarrafa albarkatun ƙasa masu mahimmanci da kuma kula da abubuwa masu guba.

Rashin yarda: Ma'aikatar saiti na watsa ikon wannan samfurin shine ≤ 20dBm. Da fatan za a daidaita shi daidai da dokokin gida. Sakamakon lalacewa ta hanyar gyare-gyare mara kyau za a ɗauka ta mai amfani.

Figures da misalai a cikin wannan jagorar an ba da su don tunani kawai kuma suna iya bambanta da ainihin bayyanar samfur. Za a iya canza ƙira da ƙayyadaddun samfur ba tare da sanarwa ba.

Takardu / Albarkatu

FLYSKY FRM303 Multi-Ayyukan Babban Ayyukan RF Module [pdf] Jagoran Jagora FRM303, FRM303 Multi-Ayyukan Babban Ayyukan RF Module, Babban Ayyukan RF Module, Babban Ayyukan RF Module, RF Module, Module

Magana

• Manual mai amfani