boqi DMX512 Mai Rarraba Mai Rarraba RDM Universal

Gabatarwar aiki

Muhimmi: Karanta Duk Umarni Kafin Shigarwa

Bayanan samfur

A'a.	Shigar da Voltage	Fitowar Yanzu	Ƙarfin fitarwa	Jawabi	Girman (LxWxH)
1	12-48VDC	4 x5A@12-36VDC 4×2.5A@48VDC	4x(60-180)W@12-36VDC 4 x120W@48VDC	Maɗaukaki voltage	178x46x22mm
2	12-48VDC	4 x350mA	4x (4.2-16.8) W	Matsakaicin halin yanzu	178x46x22mm
3	12-48VDC	4 x700mA	4x (8.4-33.6) W	Matsakaicin halin yanzu	178x46x22mm

• Standard DMX512 mai yarda iko dubawa.
• Yana goyan bayan aikin RDM.
• 4 Tashoshin fitarwa na PWM.
• DMX adireshin da aka saita da hannu.
• Yawan tashar DMX daga 1CH ~ 4CH saiti.
• Fitar da mitar PWM 2KHz
• Ƙimar gamma mai ƙyalƙyali mai ƙima daga 0.1 ~ 9.9 saiti.
• Don aiki tare da mai maimaita wuta don faɗaɗa ikon fitarwa mara iyaka.
• Mai hana ruwa daraja: IP20.

Tsaro & Gargaɗi

• KAR KA shigar da wutar lantarki da ake amfani da na'urar.
• KAR KA bijirar da na'urar ga danshi.

Aiki

Don saita adireshin DMX512 da ake so ta maɓalli,
baton A shine saita matsayi "daruruwan",
button B shine saita matsayi "tens",
button C shine saita matsayin "naúrar".

Saita adireshin DMX (adireshin DMX na masana'anta shine 001)
Latsa ka riƙe ƙasa kowane ɗayan maɓallan 3 sama da daƙiƙa 3, nunin dijital na walƙiya don shigar da saitin adireshi, sannan ka ci gaba da ɗan gajeren latsa maɓallin A don saita matsayi “daruruwan”, maɓallin B don saita matsayin “tens”, maɓallin C don saita “ matsayin raka'a, sannan danna ka riƙe kowane maɓalli na tsawon daƙiƙa 3 don tabbatar da saitin.

Alamar siginar DMX (lambar 0 na "daruruwan" matsayi na adireshin DMX): Lokacin da aka gano shigar da siginar DMX, lambar 0 na "daruruwan" matsayi na adireshin DMX zai tsaya a kai. Idan babu shigar da sigina, lambar 0 na matsayin "daruruwan" na adireshin DMX za ta kiftawa.

Zaɓi tashar DMX (Tsohon tashar DMX na masana'anta shine 4CH)
Latsa ka riƙe maɓallan B+C biyu a lokaci guda na sama da daƙiƙa 3, CH dijital nuni walƙiya, sa'an nan ci gaba da gajeren latsa maɓallin A don zaɓar 1/2/3/4, wanda ke nufin jimlar tashoshi 1/2/3/4. Latsa ka riže maballin A don > 3 seconds don tabbatar da saitin. Tsohuwar masana'anta shine tashoshi 4 DMX.

Don misaliamphar an riga an saita adireshin DMX azaman 001.
1CH=1 adireshin DMX na duk tashoshin fitarwa, wanda duk zai zama adireshin 001.
2CH=2 adireshin DMX, fitarwa 1&3 zai zama adireshin 001, fitarwa 2&4 zai zama adireshin 002
3CH=3 adiresoshin DMX, fitarwa 1, 2 zai zama adireshin 001, 002 bi da bi, fitarwa 3&4 zai zama adireshin 003
4CH=4 adireshin DMX, fitarwa 1, 2, 3, 4 zai zama adireshin 001, 002, 003, 004 bi da bi.

Mitar PWM (2KHz)
An daidaita mitar PWM @ 2KHz kuma ba za a iya canzawa ba.

Zaɓi Ƙimar Gamma Dimming Curve (ƙimar madaidaicin madaidaicin masana'anta shine g1.5)
Latsa ka riƙe dukkan maɓallan A+B+C a lokaci guda na sama da daƙiƙa 3, nuni na dijital yana walƙiya g1.5, 1.5 yana nufin ƙimar gamma mai dimming, ana iya zaɓar ƙimar daga 0.1-9.9, sannan a ci gaba da danna maɓallin B da maɓallin C. don zaɓar lambobi masu dacewa, sannan danna kuma ka riƙe ƙasa biyu maɓallan B+C don> 3 seconds don tabbatar da saitin.

Sabunta firmware OTA 

Za ku sami wannan bayan wuta akan mai kashewa, yana nufin wannan mai gyara yana goyan bayan aikin sabunta OTA na firmware. Ana iya amfani da wannan aikin lokacin da aka sami sabuntawar firmware daga masana'anta, ana iya aiwatar da sabuntawa ta hanyar kwamfutar Windows da kebul zuwa mai canza tashar tashar jiragen ruwa, mai musanya zai haɗa kwamfutar da tashar tashar dikodi ta hard waya DMX. Za'a yi amfani da software RS485-OTW akan kwamfutar don tura firmware zuwa na'urar tantancewa.

Haɗa kwamfutar da dikodi ta hanyar kebul zuwa serial port Converter, idan kana buƙatar sabunta firmware na decoders da yawa, haɗa mai canzawa zuwa tashar dikodi ta DMX ta farko, sannan haɗa sauran na'urori zuwa na'urar dikodi ta farko a sarkar daisy ta tashar tashar DMX. Don Allah kar a kunna dikodi.

Gudun kayan aikin OTA RS485-OTW akan kwamfutar, zaɓi tashar sadarwa daidai "USB-SERIAL" , baud rate "250000", da bit data "9", yi amfani da saitunan tsoho don wasu saitunan. Sannan danna"file” don zaɓar sabon firmware daga kwamfutar, sannan danna “Open Port”, za a loda firmware. Sannan danna "Zazzage Firmware", ginshiƙi na gefen dama na kayan aikin OTA zai nuna "aika hanyar haɗi". Sa'an nan iko a kan dikodi kafin "jira eraase" nuni a kan jihar ginshiƙi, dijital nuni na decoders zai nuna. . Sa'an nan "wait eraase" zai nuna a kan ginshiƙi na jihar, wanda ke nufin farawa sabuntawa. Daga nan sai kayan aikin OTA ya fara rubuta bayanai zuwa ga na'urori, sashin jihar zai nuna ci gaban da aka samu, da zarar an gama rubuta bayanan, nunin dijital na na'urar za ta haska. , wanda ke nufin an sabunta firmware cikin nasara.

Mayar zuwa Saitin Tsohuwar Masana'anta

Latsa ka riƙe maɓallan A+C biyu sama da daƙiƙa 3 har sai nunin dijital ya kashe sannan ya kunna
sake, duk saituna za a mayar zuwa factory tsoho.
Saitunan tsoho sune kamar haka:
DMX adireshin: 001
DMX Adadin Adireshin: 4CH
Yanayin PWMSaukewa: PF2
Gammaku: g1.5

Alamar Ganowar RDM:

Lokacin amfani da RDM don gano na'urar, nuni na dijital zai yi walƙiya kuma fitilun da aka haɗa su ma za su yi haske a mitar guda don nunawa. Da zarar nuni ya daina walƙiya, hasken da aka haɗa shima yana daina walƙiya.

RDM PIDs masu goyan bayan sune kamar haka: 

DISC_UNIQUE_BRANCH
DISC_MUTE
DISC_UN_MUTE
DEVICE_INFO
DMX_START_ADDRESS
IDENTIFY_DEVICE
SOFTWARE_VERSION_LABEL
DMX_PERSONALITY
DMX_PERSONALITY_DESCRIPTION
SLOT_INFO
SLOT_DESCRIPTION
MANUFACTURER_LABEL
SUPPORTED_PARAMETERS

Girman Samfur

Tsarin wayoyi

1. Lokacin jimlar nauyin kowane mai karɓa bai wuce 10A ba
   
   1. Lokacin jimlar nauyin kowane mai karɓa ya wuce 10A
      

Takardu / Albarkatu

boqi DMX512 Mai Rarraba Mai Rarraba RDM Universal [pdf] Jagoran Jagora DMX512 Universal RDM Mai Rarraba Dikodi, DMX512, Universal RDM Mai Rarraba Dikodi, Mai Rarraba Mai Rarraba RDM

Magana

• Manual mai amfani