Beijer ELECTRONICS GT-228F Digital Output Module Manual

Wannan littafin ya ƙunshi bayani kan software da kayan masarufi na Beijer Electronics GT-228F Digital Output Module. Yana ba da ƙayyadaddun bayanai masu zurfi da jagora akan shigarwa, saiti, da amfani da samfurin.

Alamomin da Aka Yi Amfani da su a cikin Wannan Jagoran

Wannan ɗaba'ar ya haɗa da Gargaɗi, Tsanaki, Bayanan kula da gumaka masu mahimmanci inda suka dace don nuna masu alaƙa da aminci ko wasu mahimman bayanai.

Ya kamata a fassara alamomin da suka dace kamar haka:

Tsaro

Kafin amfani da wannan samfurin, da fatan za a karanta wannan jagorar da sauran littattafan da suka dace a hankali. Biya cikakken hankali ga umarnin aminci!
Babu wani abu da Beijer Electronics zai kasance da alhakin ko alhakin lalacewa sakamakon amfani da wannan samfurin.

Hotunan, examples da zane-zane a cikin wannan jagorar an haɗa su don dalilai na misali.
Saboda yawancin masu canji da buƙatun da ke da alaƙa da kowane takamaiman shigarwa, Beijer Electronics ba zai iya ɗaukar nauyi ko alhaki don ainihin amfani dangane da tsohonamples da zane-zane.

Takaddun shaida na samfur

Samfurin yana da takaddun shaida masu zuwa.

Janar Bukatun Tsaro

GARGADI: Kada a haɗa samfuran da wayoyi tare da wutar da aka haɗa da tsarin. Yin haka yana haifar da “bakin filashi”, wanda zai iya haifar da al’amura masu haɗari da ba zato ba tsammani (ƙonawa, wuta, abubuwa masu tashi, matsa lamba, fashewar sauti, zafi).
Kar a taɓa tubalan tasha ko na'urorin IO lokacin da tsarin ke gudana. Yin hakan na iya haifar da girgiza wutar lantarki, gajeriyar kewayawa ko rashin aiki na na'urar.
Kada ka bari abubuwan ƙarfe na waje su taɓa samfurin lokacin da tsarin ke gudana. Yin hakan na iya haifar da girgiza wutar lantarki, gajeriyar kewayawa ko rashin aiki na na'urar.
Kada ka sanya samfurin kusa da abu mai ƙonewa. Yin hakan na iya haifar da gobara.
Duk aikin wayoyi ya kamata injiniyan lantarki ya yi.
Lokacin sarrafa kayan aikin, tabbatar da cewa duk mutane, wurin aiki, da maruƙan sun yi ƙasa sosai.
Ka guji taɓa abubuwan da aka haɗa, Modulolin sun ƙunshi abubuwan lantarki waɗanda za a iya lalata su ta hanyar fitarwar lantarki.
HANKALI: Kada a taɓa amfani da samfurin a cikin yanayin zafi sama da 60 ℃. Guji sanya samfurin a cikin hasken rana kai tsaye.
Kada a taɓa amfani da samfurin a cikin mahallin sama da 90% zafi.
Yi amfani da samfur koyaushe a cikin mahalli tare da gurɓataccen digiri 1 ko 2.
Yi amfani da madaidaicin igiyoyi don yin wayoyi.

Game da Tsarin G-jerin

Tsarin ya ƙareview

Module Adaftar hanyar sadarwa - Tsarin adaftar cibiyar sadarwa yana samar da hanyar haɗin kai tsakanin bas ɗin filin da na'urorin filin tare da kayan haɓakawa.
Ana iya kafa haɗin kai zuwa tsarin bas na filin daban-daban ta kowane nau'ikan adaftar hanyar sadarwa masu dacewa, misali, don MODBUS TCP, Ethernet IP, EtherCAT, PROFINET, CC-Link IE Field, PROFIBUS, CANopen, DeviceNet, CC-Link, MODBUS/Serial, da sauransu.
Module Fadada - nau'ikan nau'ikan haɓakawa: Digital IO, Analog IO, da kayayyaki na musamman.

Saƙo - Tsarin yana amfani da saƙo iri biyu: Saƙon sabis da saƙon IO.

IO Tsarin Taswirar Bayanai

Tsarin fadada yana da nau'ikan bayanai guda uku: bayanan IO, sigogin daidaitawa, da rajistar ƙwaƙwalwar ajiya. Ana yin musayar bayanai tsakanin adaftar cibiyar sadarwa da tsarin haɓakawa ta hanyar aiwatar da bayanan hoto na IO ta hanyar yarjejeniya ta ciki.

Gudun bayanai tsakanin adaftan cibiyar sadarwa (ramummuka 63) da kuma abubuwan haɓakawa

Bayanan bayanan shigarwa da fitarwa sun dogara ne akan matsayin ramin da nau'in bayanai na ramin fadadawa.
Yin odar shigarwa da fitarwa bayanan hoto yana dogara ne akan matsayi na faɗaɗawa.

Lissafi don wannan tsari an haɗa su a cikin litattafan adaftar cibiyar sadarwa da tsarin IO masu shirye-shirye.
Ingantattun bayanan siga ya dogara da samfuran da ake amfani da su.
Don misaliample, na'urorin analog suna da saitunan ko dai 0-20 mA ko 4-20 mA, kuma na'urorin zafin jiki suna da saituna kamar PT100, PT200, da PT500.

Takaddun bayanai na kowane nau'i yana bayyana bayanan siga.

Ƙayyadaddun bayanai

Ƙayyadaddun Muhalli

Yanayin aiki	-20°C – 60°C
UL zafin jiki	-20°C – 60°C
Yanayin ajiya	-40°C – 85°C
Dangi zafi	5%-90% ba condensing
Yin hawa	DIN dogo
Shock aiki	IEC 60068-2-27 (15G)
Juriya na rawar jiki	IEC 60068-2-6 (4 g)
Fitar masana'antu	EN 61000-6-4: 2019
Kariyar masana'antu	EN 61000-6-2: 2019
Matsayin shigarwa	A tsaye da a kwance
Takaddun shaida na samfur	CE, FCC, UL

Gabaɗaya Bayani

Rashin wutar lantarki	Max. 50mA @ 5 VDC
Kaɗaici	I/O zuwa Hankali: Keɓewar Photocoupler Ikon filin: Rashin ware
UL filin iko	Ƙarar voltage: 24 VDC maras kyau, Class 2
Ƙarfin filin	Ƙarar voltage: 24 VDC mai lamba Voltage kewayon: 15-30 VDC Rashin wutar lantarki: 40mA @ 24 VDC
Waya guda ɗaya	I/O na USB max. 0.75 mm² (AWG 18)
Nauyi	48g ku
Girman module	12 x 109 mm x 70 mm

Girma

Girman module (mm)

Ƙimar fitarwa

Fitar kowane module	Nau'in tushen maki 16
Manuniya	16 koren fitarwa matsayi
Fitarwa voltage kewayon	24 VDC mara kyau 15 VDC - 30 VDC
On-jihar voltagda drop	Max. 1.5 VDC @ 2 A
On-jihar min. halin yanzu	Min. 1 mA
yoyon waje na halin yanzu	Max. 0.5 ku
Jinkirin siginar fitarwa	KASHE zuwa: Max. 0.1 ms KUNNA zuwa KASHE: Max 0.8 ms
Fitar da ƙimar halin yanzu	Koma zuwa ƙayyadaddun adaftar cibiyar sadarwa: • GT-9XXX: Max. 2.0 A kowane tashar / Max. 10 A kowace raka'a • GL-9XXX: Max. 2.0 A kowane tashar / Max. 8 A kowace raka'a
Kariya	Babu
Nau'in gama gari	maki 16 / 2 COM

Tsarin Waya

Fil babu.	Bayanin sigina
0	Fitar tashar 0
1	Fitar tashar 1
2	Fitar tashar 2
3	Fitar tashar 3
4	Fitar tashar 4
5	Fitar tashar 5
6	Fitar tashar 6
7	Fitar tashar 7
8	Fitar tashar 8
9	Fitar tashar 9
10	Fitar tashar 10
11	Fitar tashar 11
12	Fitar tashar 12
13	Fitar tashar 13
14	Fitar tashar 14
15	Fitar tashar 15
16	Na gama gari (Ikon Filin 0V)
17	Na gama gari (Ikon Filin 0V)

Alamar LED

LED no.	Ayyukan LED / bayanin	LED launi
0	OUTPUT tashar 0	Kore
1	OUTPUT tashar 1	Kore
2	OUTPUT tashar 2	Kore
3	OUTPUT tashar 3	Kore
4	OUTPUT tashar 4	Kore
5	OUTPUT tashar 5	Kore
6	OUTPUT tashar 6	Kore
7	OUTPUT tashar 7	Kore
8	OUTPUT tashar 8	Kore
9	OUTPUT tashar 9	Kore
10	OUTPUT tashar 10	Kore
11	OUTPUT tashar 11	Kore
12	OUTPUT tashar 12	Kore
13	OUTPUT tashar 13	Kore
14	OUTPUT tashar 14	Kore
15	OUTPUT tashar 15	Kore

Matsayin Tasha

Matsayi	LED	Ya nuna
Ba sigina ba	Kashe	Aiki na al'ada
Kan sigina	Kore	Aiki na al'ada

Taswirar Bayanai Zuwa Ƙimar Hoton

Fitar Hoton Darajar

Bit no.	Bit 7	Bit 6	Bit 5	Bit 4	Bit 3	Bit 2	Bit 1	Bit 0
Baiti 0	D7	D6	D5	D4	D3	D2	D1	D0
Baiti 1	D15	D14	D13	D12	D11	D10	D9	D8

Bayanan Module na fitarwa

D7	D6	D5	D4	D3	D2	D1	D0
D15	D14	D13	D12	D11	D10	D9	D8

Bayanan Sigar

Tsawon siga mai inganci: 4 Bytes

Bit no.	Bit 7	Bit 6	Bit 5	Bit 4	Bit 3	Bit 2	Bit 1	Bit 0
Baiti 0	Ayyukan kuskure (ch0-ch7) 0: Ƙimar kuskure, 1: Rike jihar ta ƙarshe
Baiti 1	Ayyukan kuskure (ch8-ch15) 0: Ƙimar kuskure, 1: Rike jihar ta ƙarshe
Baiti 2	Ƙimar kuskure (ch0-ch7) 0: Kashe, 1: Kunna
Baiti 3	Ƙimar kuskure (ch8-ch15) 0: Kashe, 1: Kunna

Saitin Hardware

HANKALI: Koyaushe karanta wannan babin kafin shigar da tsarin!
Zafi mai zafi! Fuskar gidan na iya zama zafi yayin aiki. Idan ana amfani da na'urar a cikin yanayin yanayin zafi, koyaushe bari na'urar ta yi sanyi kafin ta taɓa ta.
Yin aiki akan na'urori masu ƙarfi na iya lalata kayan aiki! Koyaushe kashe wutar lantarki kafin aiki akan na'urar.

Bukatun sararin samaniya

Zane-zane masu zuwa suna nuna buƙatun sarari lokacin shigar da samfuran G-jerin. Tazarar tana haifar da sarari don samun iska kuma yana hana tsangwama na lantarki da aka gudanar daga yin tasiri.
Matsayin shigarwa yana aiki a tsaye da a kwance. Hotunan misalai ne kuma maiyuwa ba su kai daidai ba.

HANKALI: RASHIN bin buƙatun sarari na iya haifar da ɓata samfurin.

Dutsen Module zuwa DIN Rail

Babi masu zuwa suna bayyana yadda ake hawan tsarin zuwa dogo na DIN.

HANKALI: Dole ne a daidaita tsarin zuwa layin dogo na DIN tare da maƙallan kullewa.

Dutsen GL-9XXX ko GT-XXXX Module

Umurnai masu zuwa sun shafi waɗannan nau'ikan samfuri.

GL-9XXX
GT-1XXX
GT-2XXX

GT-3XXX
GT-4XXX
GT-5XXX

GT-7XXX
GN-9XXX kayayyaki suna da levers na kulle guda uku: ɗaya a ƙasa da biyu a gefe. Don umarnin hawa, koma zuwa Module Dutsen GN-9XXX.
Dutsen zuwa DIN dogo

Sauke daga DIN dogo

Module Dutsen GN-9XXX

Don hawa ko saukar da adaftar cibiyar sadarwa ko tsarin IO mai tsari tare da sunan samfurin GN-9XXX, don ex.ample GN-9251 ko GN-9371, duba umarni masu zuwa.

Dutsen zuwa DIN dogo
Sauke daga DIN dogo

Tushen Tasha Mai Cirewa

Don hawa ko saukar da toshe mai cirewa (RTB), duba umarnin da ke ƙasa.
Dutsen toshe mai cirewa
Rage shingen tasha mai cirewa

Haɗa igiyoyi zuwa Toshe Tasha Mai Cirewa

Don haɗa/cire haɗin igiyoyi zuwa/daga cikin toshe mai cirewa (RTB), duba umarnin da ke ƙasa.
GARGADI: Koyaushe amfani da shawarar samarwa voltage da mita don hana lalacewar kayan aiki da kuma tabbatar da kyakkyawan aiki.

Haɗa kebul
Cire haɗin kebul

Jagorar Waya

GARGADI: Kula da iyakar fitarwa na halin yanzu na I/O module. Sassan na iya lalacewa!
Kar a haɗa shigarwar da GND fil ba tare da wani kaya ba. Sassan na iya lalacewa! Idan kana amfani da 1A na yanzu, kar a yi amfani da tashar ta gaba.

Wurin Wuta da Fil ɗin Bayanai

Ana gudanar da sadarwa tsakanin adaftar cibiyar sadarwa ta G-jerin da tsarin fadada, da kuma tsarin / filin samar da wutar lantarki na motocin bas, ta hanyar bas na ciki. Ya ƙunshi Filayen Wutar Wuta 2 da Fin Data 6.
GARGADI: Kar a taɓa bayanan da filayen ikon filin! Taɓawa na iya haifar da lalacewa da lalacewa ta hanyar hayaniyar ESD.

Fil babu.	Suna	Bayani
P1	Tsarin VCC	Samar da tsarin voltage (5VDC)
P2	Tsarin GND	Tsarin ƙasa
P3	Fitowar alama	Token fitarwa tashar jiragen ruwa na processor module
P4	Serial fitarwa	Mai watsa fitarwa tashar jiragen ruwa na processor module
P5	Shigar da serial	Mai shigar da tashar tashar mai karɓar mai sarrafawa
P6	Ajiye	An tanada don alamar wucewa
P7	Filin GND	Filin filin
P8	Filin VCC	Samar da filin voltage (24VDC)

Haƙƙin mallaka

Bayanin da ke cikin wannan takarda yana iya canzawa ba tare da sanarwa ba kuma ana bayar da shi kamar yadda yake a lokacin bugawa. Beijer Electronics AB yana da haƙƙin canza kowane bayani ba tare da sabunta wannan ɗaba'ar ba.
Beijer Electronics AB ba ta da alhakin kowane kurakurai da ka iya bayyana a cikin wannan takarda. Duk examples a cikin wannan takarda an yi niyya ne kawai don inganta fahimtar ayyuka da sarrafa kayan aiki.

Beijer Electronics AB ba zai iya ɗaukar kowane alhaki ba idan waɗannan tsoffinampAna amfani da les a ainihin aikace-aikace.
Ganin yawan aikace-aikacen wannan software, masu amfani dole ne su sami isasshen ilimi da kansu don tabbatar da cewa an yi amfani da shi daidai a takamaiman aikace-aikacen su.
Mutanen da ke da alhakin aikace-aikacen da kayan aiki dole ne su tabbatar da cewa kowane aikace-aikacen ya bi duk buƙatun da suka dace, ma'auni, da dokoki dangane da tsari da aminci.

Beijer Electronics AB ba za ta karɓi wani alhaki ga duk wani lahani da ya faru yayin shigarwa ko amfani da kayan aikin da aka ambata a cikin wannan takarda. Beijer Electronics AB ya haramta duk gyare-gyare, canje-canje, ko canza kayan aiki.
Babban ofishi
Beijer Electronics AB girma

Akwatin 426
201 24 Malmö, Sweden
www.beijerelectronics.com

+ 46 40 358600

FAQ

Tambaya: Akwai kariyar gajeriyar kewayawa akan GT-228F Digital Output Module?
- A: A'a, tsarin ba shi da kariyar gajeriyar kewayawa. Ya kamata a kula don guje wa gajerun kewayawa yayin shigarwa da amfani.

Tambaya: Wane nau'in tasha ne module ɗin ke amfani da shi?
- A: Module yana amfani da keji clamp tashoshi don sauƙi kuma amintaccen haɗin wayoyi.

Takardu / Albarkatu

Beijer ELECTRONICS GT-228F Tsarin Fitar Dijital [pdf] Manual mai amfani
GT-228F Na'urar Fitar Dijital, GT-228F, Tsarin Fitar Dijital, Module na Fitowa, Module

Magana

Manual mai amfani

Beijer ELECTRONICS GT-228F Tsarin Fitar Dijital

Umarnin Amfani da samfur

Game da Wannan Jagoran