GuliKit NS79 MAX Controller User Manual

GuliKit KK4 MAX Controller

GuliKit KK4 MAX Controller

Home Button

• Power On: Tap the Home button once.
• Power Off: Press and hold the Home button for 15 seconds.
• Solid White: Operating normally.
• Solid Blue: Custom settings active.
• Slow Flashing: Low battery.
• Fast Flashing: Pairing mode.

Power Management Features

• Press the power-off button on the back to turn it off.
• The controller will automatically power off after 15 minutes of inactivity.
• When connected via USB or Auto-Continuous Fire (Turbo) is active, the controller will not power off.
• The controller automatically powers off and enters charging mode when placed on the dock. It will automatically power back on when picked up.

CAUTION! This product contains small parts (such as buttons, joystick caps, and screws) that may pose a choking hazard if swallowed by children.

Joysticks CalibrationWhile the controller is powered on, press and hold the “L”, “R”, “D-pad Left” and “A” buttons simultaneously for 6 seconds to enter calibration mode. During calibration, rotate both the left and right joysticks in full circles 2 to 3 times. Once calibration is complete, the controller will vibrate once to indicate success and will automatically exit calibration mode.

PC Gyroscope Calibration

While the controller is powered on and placed on a flat surface, press and hold the “Settings”, “D-pad Left”, and “A” buttons simultaneously to initiate automatic gyroscope calibration. Once calibration is complete, the controller will vibrate once to indicate success. *Note: Calibration is not necessary when the gyroscope is functioning normally.

Pairing On PC

Bluetooth Pairing – 730Hz Polling Rate(Requires the computer to have Bluetooth functionality)

1. Switch the controller to PC or PS mode. Then press and hold the pairing button for 2 seconds until the indicator light begins flashing rapidly, indicating that pairing mode has started.
2. On your computer, open the Bluetooth settings, search for new devices, and select “GuliKit XW Controller” or “Gulikit Controller PS” to pair.
3. Once the interface displays “Connected”, the pairing is complete.

Wired Connection – 1000Hz Polling Rate

1. Set the controller to the desired mode.
2. Connect it to your computer’s USB port using a USB cable. * If it is a desktop computer, it is recommended to plug it into the USB port on the back of the computer case.

Pairing with Controller Dock on PC

1. Set to PC mode, press and hold the pairing button for 2s until the LED flashes fast to start pairing.
2. Connect the controller dock to the PC using the included cable.
3. Pairing is complete when the PC displays that a new controller is connected.

Pairing On Android, iOS, macOS Devices

1. The controller can be set to any mode.
2. Press and hold the pairing button for 2 seconds until the indicator light starts blinking quickly, indicating that pairing mode has been activated.
3. On your device’s Bluetooth settings, search for new devices, and select “GuliKit XW Controller” or “Gulikit Controller PS” to pair.
4. The interface will display “Connected” when the pairing is complete.

Pairing On Switch / Switch 2

1. Set the controller to NS mode, turn it on, then press and hold the pairing button for 2 seconds. The indicator light will blink quickly, indicating that pairing has started.
2. Turn the Switch / Switch 2 to the black screen (sleep) state, press the HOME button on the Joy-Con to wake it up. Then enter the controller pairing interface as shown.

Once the interface shows that a new controller is connected, the pairing is complete.

Use Method of Auto Pilot Gaming Function (APG)Long press the Learn button for 3 seconds (short vibration) > Perform controller actions > Press the Learn button to end (long vibration).

• Single Playback: Short press the APG button.
• Repeat Playback: Double-click the APG button.
• During the replay, you can use the joystick for movement, allowing you to perform actions while moving.
• To cancel the replay midway, press any other button.
• Maximum recording time is 10 minutes.

Back Button Configuration Mapping

Using Buttons: Settings Button + G1 / G2 / G3 / G4

• Back Button Mapping: Settings button (short vibration) + Back button > Press the button you want to map.
• Cancel Mapping: Settings button + Back button (long vibration) cancels the current back button mapping.
• *The back buttons can only map to normal key functions and do not support the Continuous Fire (Turbo) feature.

Back Button APG Function

Using Buttons: APG Button + G1 / G2 / G3 / G4

APG button + Back button > Perform controller actions > Press the APG button to end.

• Single Playback: Short press the Back button.
• *All 4 back buttons support up to a 30-second APG recording.

Trigger Mode Setting MethodSupports both Hall Effect Analog Trigger and Micro-switch Digital Trigger modes.
By toggling the switch on the back, you can easily switch the ZL and ZR triggers between the digital tactile switch trigger mode and Hall effect analog trigger mode. * Make sure the triggers are released before switching the trigger modes.

Mic Settings

• ON/OFF: Press & hold the Mic key to turn ON/OFF. The Mic key stays solidly lit when enabled.
• Sensitivity: Short press the Mic button to adjust the Mic sensitivity (with vibration feedback). Sensitivity levels cycle through Low, Medium, and High.
• Mic Demo Function: When the controller is placed on the dock, long press the Mic button to turn on the Mic. The Mic will detect external sounds, and the joystick ring light will pulse dynamically to the sounds.

General Rules for Special Function Settings

• All special function settings mentioned below require holding down the Setting button while pressing the corresponding buttons for configuration.
• All special settings will be automatically saved.
• When no special settings are configured, the logo light will be white. When special settings are active, the logo light will be blue.
• When the battery is low, the logo light will flash, and vibration will automatically turn off. When charging restores the battery level, vibration will turn back on.

Settings Button Combinations:+ Clear All Settings (Reset)

Long vibration: Indicates that the reset process is complete, and the controller has been restored to factory settings.

+ Joystick Dead Zone Mode

• One Vibration: Joystick dead zone ON with anti-snapback mode.
• Long Vibration: Joystick dead zone OFF. (Default)

+ A / B / X / Y / R / ZR Continuous Fire (Turbo)

• One Vibration: Normal Continuous Fire. Active while holding the button down, stops when released.
• Two Vibrations: Auto Continuous Fire. Press once to initiate, press again to stop.
• Long Vibration: Cancel Continuous Fire.

+ A-B X-Y Input Swap

• One Vibration: Swaps input values of the A-B and X-Y buttons.
• Long Vibration: Restores default assignments.

+ Vibration Intensity Adjustment

• One Vibration: Weak vibration.
• Two Vibrations: Standard vibration. (Default)
• Three Vibrations: Strong vibration.
• Long Vibration: Turn off vibration.

+ Vibration Mode Adjustment

• One Vibration: Rotary Motor mode.
• Two Vibrations: GuliKit Maglev Haptic mode. (Default on PC)
• Three Vibrations: HD vibration mode. (Default on Switch)

+ R3 / L3 Joystick Sensitivity Adjustment

• One Vibration: Sensitivity 50%
• Two Vibrations: Sensitivity 100%. (Default)
• Three Vibrations: Sensitivity 150%.
• *R3 and L3 refer to pressing down on the joysticks. Each joystick can be configured independently.

+ 8 / 4-direction on D-pad

• One Vibration: Switches D-pad to 4-direction mode.
• Long Vibration: Restores default 8-direction mode. (Default)

+ L / ZL Set Motion Aim Assist (PC FPS Games)

• One Vibration: Low sensitivity aim assist.
• Two Vibrations: Medium sensitivity aim assist.
• Three Vibrations: High sensitivity aim assist.
• Long Vibration: Disable motion aim assist. (Default)
• +L: Set motion assist to activate when the L button is held in-game.
• +ZL: Set motion assist to activate when the ZL trigger is held in-game.

+ Star Ring Lighting Effects

Cycles through: Default Steady On > Joystick-activated Flowing Light > Colorful Flowing Light > Trigger-activated Flowing Light > Off > Repeat.

+ APG Recording File Share

Enables APG read/write mode. Insert the USB data cable into your computer to locate a USB drive named “GuliKit dat”. Inside, the “Auto.apg” file contains your APG recording. You can copy this file for backup or sharing. To overwrite existing data, copy a new APG file into the drive and replace the existing file.

• *Once the writing process is complete, the controller will automatically power off.
• *Do not alter the file name to ensure proper functionality.

FCC Warning

Labeling requirements
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Information to user
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Information to the userNote: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.