GP Airtech E600 Field Controller
Product Usage Instructions
- To power on the E600 Field Controller, press and hold the power button for a few seconds. To power off, repeat the same process.
- Ensure that the device is within range of the desired Wi-Fi network or Bluetooth devices for proper connectivity.
- Configure the network settings as per your requirements and ensure compatibility with the available bands and frequencies.
- If you encounter any connectivity issues or errors, refer to the user manual for troubleshooting steps or seek assistance from a qualified technician.
This manual is for reference only.
There might be subtle differences between the actual product and the picture.
Please refer to the actual product.
Please read this manual before using the product.
Product
Installation of SIM card and SD Card
- Please pay attention to the direction of the slot when inserting the card Inserting a non-standard card may cause damage to the SIM card holder of the device.
- Open the SIM/ SD plug first and take out the card tray with the PIN. Then you can insert the SIM and SD card
Warning!
- Please pay attention to safety when using a PIN to prevent finger injury or damage to equipment.
- Please take good care of the PIN and keep it out of the reach of children, to prevent children from swallowing or poking it unintentionally.
Restart Device
- Holding the power button for 2 seconds, choose restart.
Force Device Restart
- Holding the power button for over 8 seconds.
Charge
- Charging the device before first use is recommended.
- Note: The charger plugs should be fully plugged into the socket and kept in an easy-to-unplug location.
Safety Information
- Device is designed for working in -20°C ~55 C environment, proper storage temperature is -30 C ~60 C, lower or higher temperature would compromise device performance, even cause potential damage to device or battery.
- Charge the device in a 5°C ~35 °C environment, in case of battery endurance weakness.
- No support or responsibility will be undertaken if the end user updates the device with a third-party ROM or cracks the device’s system.
Electromagnetic Radiation
The maximum absorption rate of electromagnetic radiation is (SAR) ≤ 2.0 W/kg. In special cases such as pacemakers, hearing aids, and cochlear implants, users should follow the doctor’s instructions.
Warning
The following actions may cause battery safety risks, resulting in safety problems:
- Disassemble the battery.
- Demolition device.
- Repair device in unofficial service.
- Using an uncertified USB cable.
- Put the device into or near a microwave oven, fire, or other heat source.
Product Specification
Environmental Protection
- List of toxic and hazardous substances or elements
0: indicates that the toxic and hazardous substances in all homogenized materials of the component are below the limit required by GB/T 26572-2011.
X: indicates that the toxic and hazardous substance in at least one homogeneous material of the component exceeds the limit set by GB/T 26572-2011.
Note: this product is labeled “X” because there are no alternative technologies or components available at this stage. Please handle such parts or materials properly to avoid environmental and human health effects.
This product’s “environmental protection life” is 10 years. The environmental protection of some internal or external components may differ from the environmental life of the product. The service life mark on the component has precedence over any conflicting or different environmental life identification on the product. The term of environmental protection of this product refers to the safe life of using the product without toxic and harmful substances leakage under the conditions stipulated in this information guide.
For more information
- About the device, Android and software versions, check in: settings > about the phone.
- Note: Access to the Internet, send and receive information, upload and download, and automatic synchronization, so that some applications or the use of location services may incur other costs.
- To avoid additional charges, please contact the service provider and select the appropriate tariff package scheme.
FCC Statements
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or changes to this equipment. Such modifications or changes could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The SAR limit of the USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device type E600 (FCC ID: 2BH4K-E600) has also been tested against this SAR limit.
This device was tested for typical body-worn operations with the back of the handset kept 10mm from the body.
To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 5mm separation distance between the user’s body and the back of the handset. The use of belt clips, holsters, and similar accessories should not contain metallic components in their assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements and should be avoided.
The device for operation in the band 5150–5350 MHz(for IC:5150-5250MHz) is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.
FAQ
- Q: What should I do if the device fails to connect to Wi-Fi?
- A: Check the Wi-Fi network settings on the device, ensure the correct password is entered, and verify that the device is within range of the router.
- Q: How can I update the firmware of the E600 Field Controller?
- A: Visit the manufacturer’s website to download the latest firmware update files and follow the instructions provided to update the device.
- Q: Is it possible to use the E600 Field Controller without a SIM card?
- A: Yes, the E600 Field Controller can be used without a SIM card, but certain functionalities that rely on cellular networks may not be available.
Documents / Resources
 |
GP Airtech E600 Field Controller [pdf] User Guide 2BH4K-E600, 2BH4KE600, e600, E600 Field Controller, E600, Field Controller, Controller |