Godox iT32 Camera Flash
Specifications
- Model: iT32
- Product Code: 705-YT3200-00
- Dimensions: 80*100mm
- Manufacturer: GODOX Photo Equipment Co., Ltd.
- Manufacturing Date: 2025/10/9
- Country of Origin: Made in China
- Website: www.godox.com
General Setup:
- Ensure the flash unit is compatible with your camera model.
- Attach the flash securely to your camera’s hot shoe.
- Power on the flash unit and the camera.
- Adjust flash settings (power, mode, etc.) according to your shooting needs.
- Refer to the camera’s manual for optimal flash synchronization settings.
Troubleshooting
Issue: Flash not firing.
- Check battery levels and ensure batteries are inserted correctly.
- Verify the flash is securely mounted on the camera.
- Ensure the flash is powered on.
- Check camera settings for flash synchronization.
- Test with a different camera or trigger if possible.
Issue: Inconsistent flash output.
- Ensure batteries are fully charged or replaced.
- Check for any obstructions between the flash and the subject.
- Reset flash settings to default.
Issue: Error messages on the flash unit.
- Consult the specific model’s manual for error code meanings.
- Contact customer support if the issue persists.
Customer Support
- Wechat Official Account: 2
- Telephone: +86-755-29609320 (Ext. 8062) / +86-755-25723423
- Email: godox@godox.com
- Address: Building 2, Yaochuan Industrial Zone, Tangwei Community, Fuhai Street, Bao’an District, Shenzhen 518103, China
What’s Inside
armng
• All transport protective materials and packaging on the product must be removed
before use.
• This product is a professional lighting fixture, children are prohibited from using it.
• Do not point the flash directly at the eyes (especially baby’s eyes) under any
circumstances.
• This device is not waterproof. Keep it dry and avoid immersing it in water or other
liquids. It should be installed in a ventilated and dry location and avoid using in rainy,
humid, dusty, or overheated environments. Do not place items above the device or
allow liquids to flow into it to prevent danger.
• Do not use damaged equipment or accessories, and wait for professional
maintenance personnel to check and repair to confirm being normal before use.
• Stop using immediately if the product shell is cracked due to falling, squeezing, or
strong impact, to avoid touching the internal electronic components and getting an
electric shock,
• Please refer to the electronic version of detailed instruction manual for more safety
instructions.
Name of Parts
1. Flash Head
2. Wide-angle Diffuser
(Transparent, inside the flash head)
3. Catchlight Panel (White, inside
the flash head)
4. LED Modeling Lamp
5. Photocell Sensor
6. Sync Cord Jack
7. IJSB-C Port (Charging/firmware
upgrade)
8. Touch Screen
9. MENU Button
10. SET Button
11. < > Button
12. Select Dial
13. Select Dial Alignment Marker
TTL Wireless Flash Trigger. X5C/X5N/X5S/X5F/X50 (Sold Separately)
Installing the Flash Trigger
Align the flash trigger with the bottom of the flash body in the direction as shown and
place it in, the flash will automatically absorb it. Once installed, the
> icon in the menu interface will light up.
Align the protruding side of the diffuser with the model <iT32> logo side of the flash
body, then insert it firmly until fully seated.
Mounting on the Camera
Rotate clockwise the hot shoe locking ring of the flash trigger to the top and insert
into the hot shoe mount of the camera, then rotate anticlockwise the hot shoe locking
ring until it’s firmly locked.
Note Please make sure the flash and camera are powered off before installing and disassembling.
Power Switch
Power on: Press and hold the < > button until the icon appears, then slide up on
the screen or rotate up the select dial to unlock. The device will turn off automatically
if it stays locked for 6 seconds after power on(This function can be turned off in
bootup settings, then press and hold the < > button can directly power on the
device).
Power off: Press and hold the < fid) > button until the screen blacks out.
The flash trigger X5 does not have power on/off function, users can check its
status via the indicator according to the following table:
Wi-Off Mode Settings
TTL auto flash — adjust the FEC amount
from -3.0 to +3,0 with ± 1/3 increment.
M manual flash — adjust the flash power
from I / 128 to 1/1 with ± I /3 increment.
Multi: stroboscopic flash — number of
flashes (1-100), flash frequency (1-100),
flash output range (1 / 128-1/4), details of
which refer to the electronic version of the
instruction manual.
Sender Mode Settings — Gr [Mul
Gr group setting — press and hold the group
box or SET button to switch among OFF, TTL
M manual flash — receive the M flash
signals from the sender unit.
Multi: stroboscopic flash — receive the
multi flash signals from the sender unit,
2-19
CH25 M
0432 Multi
+0.3 +
1/16
Wireless Flash Shooting (2.4G Wireless
Transmission)
To take wireless flash shooting, you will need one or more flashes that support
wireless transmission in addition to this flash, and you must pair the sender unit and
receiver unit. The group, channel, and ID of the sender unit and receiver unit must
be set to the same. Details of which refer to the electronic version of the instruction
Documents / Resources
 | iT32 Camera Flash |
References
- godox.comwww.godox.com
- User Manualmanual.tools