Intelligent Sensor Soap Dispenser

K9 Pro

Appearance

Specification

1. Accuracy: ±0.2℃ (34~45℃, put it in the operating environment for 30 minutes before use)
2. Alarm type: flashing + bleeping “DIDIDI”
3. Measuring distance: 5cm~10cm
4. LED display: Number
5. Interface: Type-C
6. Bottle Capacity: 1000mL
7. Mounting Type: Wall-hanging, Tripod-fixed
8. Working Temperature: 10℃~40℃ (15℃~35℃ Recommended)
9. Measuring range: 0~50℃
10. Response time: 500ms
11. Standby time: 5s for non-working, dynamic loop with white light
12. Power Supply: DC 5V 1500MA(or 4 AA batteries)
13. Dimension: 119*133*280mm
14. Liquid type: hand sanitizer or liquid disinfectant

Conditions

1. Standby: the white dot on the bottom of the right corner flashing by turns. (Fig. 1)
2. Normal temperature: displays current temperature and green light flashes once on the display. (Fig. 2)
3. Abnormal temperature: displays current temperature and red light flashes on the display. (Fig. 3)
4. Out of measuring range(Note: do not spray hand sanitizer):
   “Lo”: Ultra-low temperature alarm. (Fig. 4);
   “HI”: Ultra-high temperature alarm. (Fig. 5)

Instructions

1. Temperature measuring and handwashing: Put your hand on the bottom until you hear a “DI” sound, then the LED screen will display the temperature and hand sanitizer squeezed out. (Fig. 6)
2. The function of a button:
   

   (1) Button ①: Function setting(Fig. 7)

   (2)Button ②: Specific function settings(Fig. 8)

3. Function setting
   Press the button ① once to set the temperature unit
   Press the button ② to switch between Celsius and Fahrenheit C: Celsius F: Fahrenheit (Fig. 9, Fig. 10)

   Press the button ① twice to set the working mode
   Press the button ② to switch the working mode. Bo: body mode co: counting mode sure: surface mode.Press the button ① 3 times to set the alarm temperature
   Press the button ② to switch the alarm temperature from 36℃ to 39℃. Press the button ① 4 times to set the volume
   Press the button ② to switch the volume from U0 to U4. Press the button ① 5 times to set the language
   Press the button ② to set the language CH/EN/KO/PT/ES/JP/IT/DE/FR/RU/NL/AR
   CH: Chinese EN: English KO: Korean PT: Portuguese ES: Spanish JP: Japanese IT: Italian DE: German FR: French RU: Russian NL: Netherlands AR: ArabiaPress the button ① 6 times to set the squeeze amount of hand sanitizer
   Press the button ② to set the extrusion time between 0.1 and 2.0 secondsPress the Button ① for 2S or more: on/off

Mounting

(1) Tripod mounting: There is a screw connection on the bottom which can be connected with a tripod. (Fig. 11)	(2) Wall-handing: There are two hanging holes on the backside that can be fixed with nails. (Fig. 12)
(3) Desktop stand: Put the Intelligent Sensor Soap Dispenser in the desktop stand to use(Fig. 13)	(4) Wall-handing Desktop stand: there are two hanging holes on the backside that can be fixed with nails. (Fig. 14)
(5) Hanging the desktop stand on the tripod (Fig. 15)	(6)Power On/Off: Press the switch button on the right side of the device(Fig. 16)
(7)Battery installation: Open the battery cover, take out the battery box, unscrew the screws, and put in 4 AA batteries (Fig. 17).

Warnings

1. Do not pour hand sanitizer into Temperature Measuring Probe and Proximity Sensor.
2. Make sure that it is standing upright after filling in hand sanitizer.

Documents / Resources

global sources K9 Pro Intelligent Sensor Soap Dispenser [pdf] Instruction Manual K9 Pro Intelligent Sensor Soap Dispenser, K9 Pro, Intelligent Sensor Soap Dispenser

References

• User Manual