GIMBEL AUTOMATION 2024 Q2 Two Op Automation Pallet

Product Specifications

• Product Name: Gimbel Automation Two-Op Automation Pallet
• Model: 2024 Q2
• Price: Starting from $6849
• Module: Two-Op
• Features: Axis/LANG/Jergens Zero-Point

Product Usage Instructions

• Air Routing & Information
  Ensure proper airline routing according to the Air Line Guide provided with the product. Bundle each cable coming off each individual Instant Solenoid Kit for efficient operation.
• Two-Op Auto. Pallet Work Offsets
  Set the work offsets for the two operations on the pallet according to the provided guidelines to ensure accurate machining.
• Macro Program Template
  Use the provided Macro Program Template for programming automation sequences to streamline the production process.
• Jaw Configurations
  Configure the jaws of the Op-1 Vise based on the type of stock being used. Rectangular starting stock may require Op1 Soft Jaws, while round stock will need a soft jaw for the Op1 Vise.

Frequently Asked Questions

Q: How do I set up the Two-Op Auto? Pallet WCS?
A: Follow the WCS summary provided in the manual. Set OP1 VISE to G54, FLIP STATION to G56, and OP2 VISE to G55.

Q: What is the starting pickup point for the Bottom Left on the pallet?
A: The Bottom left pickup point is (0,0) in the part tray as shown in the manual.

INTRODUCTION

Two-Op Module

• Enables Two-Op One-Cycle Parts
• Includes Two 75 or 100mm Vises
• Includes Integrated Part Flipper
• Internal Air Line Routing
• Built-In 96mm Pullstuds for 5th- Axis/LANG/Jergens Zero-Point

Air Routing & Information

STANDARDIZING ROUTING

• To make routing easier, we highly recommend adopting a standard for your airline colors
• Use the same bundle color-coding on signal wires to the control

Recommended Line Color Coding

• Black is [FLOWS NORMALLY]
• Red is [FLOWS ENERGIZED]

Recommended Bundle Color Coding

• For each Instant Solenoid Kit, designate a color-coded bundle
• Wrap each bundle of four airlines with the designated color of electrical tape

Bundle each cable coming off each Instant Solenoid Kit

Two-Op Auto. Pallet Work Offsets

Macro Program Template

• Your purchase of the Two-Op Automation Pallet comes with the Machine-Appropriate Template

Turnkeys

• For Turnkeys, this Template will be edited specifically for your setup, tool numbers, and exact part

Self-Installs

• For Self-Install, you will have to edit the Program Template provided with your specific machine information

TWO OP AUTO PALLET WCSSUMMARY

First-Op Vise: G54

• The first-Op Vise is the vise closest to the user in Y-Axis configurations
• G54 X0.000 should be set to the left-to-right center of the vise for X
• G54 Y0.000 should be set to the front-to-back center of the vise for Y
• G54 Z0.000 should be set to the bottom face of the stock location during Op1 machining

Second-Op Vise: G55

• The second-Op Vise is the vise farthest from the user in Y-Axis configurations
• G55 X0.000 should be set to the left-to-right center of the vise for X
• G55 Y0.000 should be set to the front-to-back center of the vise for Y

G55 Z0.000 should be set to bottom stock height theoretical value (this is where the material from Op1 would have been, had that material not been removed

Integrated Flip Station: G56

• Integrated Flip Station is centered between the two vises
• G56 X0.000 should be set X end location of the Flip Station fingers
• G56 Y0.000 should be set to the front-to-back center of flip location
• G56 Z0.000 should be at the Flip Station flipping center of rotation

TWO OP AUTO PALLET WCS SUMMARY

Stock Tray: G59

• The stock tray should be located on the table to the right of the Automation Pallet
• G59 X0.000 should be set to the left-to-right center bottom left stock pickup point
• G59 Y0.000 should be set to the front-to-back center bottom left stock pickup point
• G59 Z0.000 should be set to the bottom face of the stock at the bottom-left pickup point
• Stock Tray should be aligned to the X-Axis of the Machine (dialed-in)

The bottom left pickup point is (0,0) in the part tray shown above

Programming Variables

• Part Information
• Tray Information
• Stock Size Information

Jaw Configurations

First-Op Jaw Configuration

• Rectangular Stock
  • For rectangular stock, use the provided adjustable hard jaws
• Round Stock
  • In the case of round stock, we recommend cutting Op1 Soft Jaws
  • A note about WCS: Once the soft jaw has been cut, the Z-axis G54 WCS should be moved so that the stock bottom in the Op1 Jaw is at G54 Z0.000

Second-Op Jaw Configuration

• Rectangular Parts
  • For rectangular stock, it is sometimes possible to use the square jaws
  • When doing this, be careful as the serrated teeth can mar the part
• Most Parts
  • In most cases, the Op2 Vise Requires soft jaws to match the part profile

 

 

 

 

Documents / Resources

GIMBEL AUTOMATION 2024 Q2 Two Op Automation Pallet [pdf] User Guide 2024 Q2, 2024 Q2 Two Op Automation Pallet, Two Op Automation Pallet, Automation Pallet, Pallet

References

• User Manual