Giada iM1-210 COM Module User Manual

Giada iM1-210 COM Module

Usage Instructions

• Unpacking: Carefully remove the Giada IM1-210 module from its packaging.
• Static Precautions: Before handling the module, ensure you are wearing a wrist-grounding strap to prevent electrostatic discharge (ESD) damage.
• Power Disconnection: Always ensure the power supply is disconnected before installing or removing any components.
• Module Installation: Mount the IM1-210 module onto a compatible carrier board according to the carrier board’s instructions. Ensure all connectors are properly aligned and seated.
• Peripheral Connections: Connect necessary peripherals such as display (HDMI, DP, eDP, or LVDS), camera (MIPI-CSI), USB devices, Ethernet cables, and serial devices to the carrier board.
• Power Connection: Connect a DC-IN 5V power supply (within the 4V to 5.25V range) to the carrier board.
• Operating System Installation: Install your chosen operating system (Windows 11 or Linux 64-bit) onto the module’s eMMC storage or an external SATA III drive. Refer to your OS installation guide for detailed steps.
• First Boot: Power on the system. Monitor the boot process and ensure all connected peripherals are recognized.
• The module supports multiple display outputs: HDMI, DisplayPort, eDP, and dual-channel LVDS.
• Note that eDP and LVDS are co-lay, meaning they share some resources and may not be usable simultaneously in all configurations. Consult your carrier board documentation for specific limitations.
• Configure display settings within your operating system to achieve desired resolutions and refresh rates (up to 4096 x 2160 @60 Hz for HDMI/DP, 3840 x 2160 @60 Hz for eDP, and 1920 x 1080 @60 Hz for LVDS).
• Connect Ethernet cables to the 2.5 Gigabit Ethernet ports on your carrier board.
• Configure network settings within your operating system to establish network connectivity. The module supports TSN (Time-Sensitive Networking).
• Connect MIPI-CSI cameras to the appropriate 2-lane or 4-lane MIPI-CSI interfaces on your carrier board.
• Install the necessary drivers and software for your specific camera modules within your operating system.

Statement

• The copyright of this manual belongs to Shenzhen JIEHE Technology Development Co., Ltd. (Giada, JIEHE’s global brand) and all rights are reserved. The company reserves the right to change this manual at any time without notification. Specifications here are for reference only, please take the real product as standard.
• Without official authorization of Giada, other companies or individuals may not copy, plagiarize, translate or disseminate this manual for commercial purposes.
• The information provided in this manual is accurate and reliable. The company does not take any legal responsibility for the consequences of infringement use of this manual.

Safety

Safety Notice

• Read the user manual carefully before setting up the Giada product.
• Disconnect the power cord before installing the internal components
• Most electronic components are sensitive to static electrical charge, please wear a wrist-grounding strap when installing the internal components.
• Don’t disconnect the power cord when the system is running to avoid damage to the sensitive components by instantaneous surge voltage.

Product Introduction

Brief Introduction

• The Giada IM1-210 is an SMARC V2.1.1 Module based on the Intel® Atom X7211RE/X7433RE with a long life cycle.
• It features integrated LPDDR5 on-board memory, on-board eMMC storage of up to 64GB.
• It offers a range of interfaces tailored for embedded applications, including GPIO extension, USB 2.0, CAN-FD, dual-channel LVDS for display, and MIPI-CSI for camera connectivity.
• These compact module is an ideal choice for automation and industrial control applications.

Motherboard Picture

Specifications

Electrical Information

Board Information

Block Diagram

Interface Definition

P-PIN Primary (Top) Side

S-Pin Secondary (Bottom) Side

Troubleshooting

No Power / System Not Booting

• Check Power Supply: Ensure the DC-IN 5V power supply is correctly connected and providing power within the specified range (4V to 5.25V).
• Module Seating: Verify that the IM1-210 module is securely seated on the carrier board.
• Carrier Board Issues: If possible, test the carrier board with another compatible module or check its power indicators.
• Static Damage: If proper ESD precautions were not followed, static damage might have occurred. Contact support.

No Display Output

• Cable Connection: Ensure display cables (HDMI, DP, LVDS, eDP) are securely connected at both ends.
• Monitor Input: Verify the monitor is set to the correct input source.
• Driver Installation: Ensure graphics drivers are correctly installed in your operating system.
• Display Compatibility: Check if the display resolution and refresh rate are supported by both the module and the monitor.
• eDP/LVDS Conflict: If using eDP or LVDS, ensure there are no conflicts with other display outputs if they are co-lay.

Peripheral Not Detected (USB, Ethernet, Serial)

• Driver Installation: Ensure all necessary drivers for your operating system are installed.
• Physical Connection: Check the physical connection of the peripheral to the carrier board.
• BIOS/UEFI Settings: Verify that the relevant ports are enabled in the system’s BIOS/UEFI settings (if applicable to your carrier board).
• Device Functionality: Test the peripheral with another system to ensure it is not faulty.

System Instability / Crashes

• Overheating: Ensure adequate airflow around the module, especially in high-temperature environments (-40°C ~ 85°C operating range). Verify that any heatsinks or cooling solutions are properly installed.
• Power Fluctuations: Use a stable power supply. Avoid disconnecting power while the system is running.
• Memory Issues: While memory is onboard, ensure the system is not running out of memory for demanding applications.
• Software Conflicts: Check for recently installed software or drivers that might be causing conflicts.

Contact Information

• Shenzhen JIEHE Technology Development Co., Ltd.
• Website: www.giadatech.com
• Phone: +86-755-3330 0336
• Email: support@giadatech.com
• Address: 37F, Holdfound Sky Plaza Office Building, 11008 Beihuan Blvd., Nanshan, SZ, China, 518051