Generic PD10 PD10S Scent Diffuser User Manual

FEATURES

• The package includes the diffuser with empty 120ml bottle, remote controller, USB cable, adapter, metal hook, spare nozzle, seal rubber ring, and user manual.
• The remote controller is designed for convenient adjustment of fragrance concentration levels to suit your preferences, as well as setting the desired operating duration for the device.
• Please follow the instructions set out in this manual and use the device correctly.

USING GUIDE 

1. Step 1: Remove Empty Bottle
   • Take the upper part of the diffuser directly.
   • Rotate the bottle counter-clockwise to remove it.
2. Step 2: Add the Fragrance oil
   • Fill the bottle with your favourite fragrance oil.
3. Step 3: Install the bottle and upper part
   • Put the upper part directly in the diffuser.
4. Step 4: Power On the Diffuser
   • Connect the device with the USB-C and adapter.
   • Use the remote controller to turn on the device, or press the power button to turn on.

LIGHT INDICATOR/ DEVICE FUNCTION
The power button on the front of the device works as both a power button and a control for misting and timer settings once the device is turned on.

1. ln order to turn the device on please press and hold the power button for 2 As seconds. mentioned in the instructions to use section, in the default setting, the device will release scent for 30 seconds and then pause for 120 seconds. This cycle will
2. To ntinue control for 4 the hours, misting after and which device the timer device using will the turn off power button, automatically. follow these steps:

Misting Control
After the device is turned on, use the power button to adjust misting settings:

• Press once: The diffuser emits scent for 30 seconds, then pauses for 60s. (L1)
• Press again: The diffuser emits scent for 30 seconds, then pauses for 120s. (L2)
• Press again: The diffuser emits scent for 30 seconds, then pauses for 180s. (L3)
• Press again: The diffuser emits scent for 30 seconds, then pauses for 240s. (L4)
• Press again: The diffuser emits scent for 30 seconds, then pauses for 300s. (L5)
• Press again: The diffuser emits scent for 30 seconds, then pauses for 360s. (L6)

Timer Settings:
To adjust the timer setting, use the instructions below, this setting allows the device to cycle through the misting setting for an extended period of time until the device automatically powers off.

• Presstwice forlhourtimer:
• Presstwice for 2 hourtimer:
• Presstwice for 4 hourtimer:
• Press twice for S hour timer:
• Press twice for cancel timer:

REMOTE CONTROLLER 

SAFETY

1. The diffuser should be used in an upright position always.
2. Do not tilt the diffuser as oil can spill inside and damage the device.
3. Do not use the device with any other power cords. Please use the original power cord that comes with diffuser. Position the power cord to prevent tripping hazard.

REPLACING THE NOZZLE

1. oil Take bottle, the pull upper out part the of small the tube. diffuser, Using and metal remove hook fragrance wiggling the nozzle and pull out the black nozzle gently.
2. Replace it with a new nozzle and ensure the nozzle is pressed very firmly into the top of the diffuser. Then reinsert the tube to the nozzle.

Note:
It is very important that you put the tube into the correct position of the otherwise the device will not diffuse scent. Within the nozzle there is a small nozzle, round tube holder that the tube needs to be firmly secured
A Tip: If you have difficulty to seethe tube holder in the into. nozzle, hold a flashlight into the nozzle to increase visibility.

WARRANTY

Your device comes with limited warranty. Please ensure that you have proof of purchase in case a claim arises. Please note that the warranty is non-transferable.
The following will not be covered under warranty:

• Damage caused by accidents or fire.
• Failure to use device properly.
• If the device is repaired by a non-authorized dealer.
• Third party parts used in the machine.

MAINTAINANCE
The scent diffuser should be cleaned every 1-2 months to ensure optimal performance. To clean the inner workings of the device, please follow these steps:

1. Take the upper part of diffuser, and fill rubbing alcohol to the bottle.
2. Install the upper part with bottle to diffuser.
3. Turn on the diffuser and keep working 15 minutes, to ensure alcohol go through the whole device.
4. Remove the electric cord from the diffuser and keep the diffuser in an upright position. Wipe the device with a damp cloth to remove oil stains and fingerprints. Don’t use any harsh or abrasive to clean the device.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction

TROUBLESHOOT