Generic AG-C204 Remote Control Switch Instruction Manual

AG-C204 Remote Control Switch Instruction Manual

I. Overview

The wireless receiver controller and three-button remote designed and manufactured by our company form a complete set of wireless digital intelligent remote control components, primarily used for controlling the forward and reverse rotation of AC motors (e.g., projection screens, electric curtains, electric overhead racks, garage doors, sliding doors, etc.). They enable the controlled equipment to achieve motor forward and reverse rotation or switch on/off operations, ensuring compatibility between wired and wireless systems.

This receiver controller features high confidentiality, large storage capacity, stable performance, and low power consumption. It is easy to use, eliminating the need for traditional jumper wires or dip switch encoding. Simply have the receiver controller capture and store the wireless signals emitted by the remote control to enable paired operation. Each receiver controller can store multiple transmitters (remote controls). If a properly learned remote control is lost during use, merely clearing the stored information from the receiver controller will render the lost remote control incapable of operating the receiver. To regain access, the owner must relearn the remote control from scratch. This not only alleviates concerns about remote control loss but also provides a convenient way to add a new remote control.

II. Technical indicators:

1. Working voltage: 220VAC ± 10%
2. Load power: ≤500W
3. Working temperature: -25°C to+75°C
4. Reception sensitivity: ≥-100dB
5. Working frequency: commonly used 315MHz, 433.92MHz (others can be customized)
6. Remote control distance: 100-500 meters (open space)
7. Output mode: Voltage (220VAC)
8. Dimensions: 102 * 62 * 30mm
9. Weight: 90 g

III. Schematic diagram

1. Connect the power and output lines of the controller according to the following diagram:

1. Electric machinery
2. Input 220 V

2. Functions of remote control and control panel buttons:

1. UP
2. Down
3. Stop
4. Connection hole

button: Up: button: Stop, power off release: button: down

IV. Pattern pairing method:

1. Learning method: First, complete the code clearing process. Then, press and hold the “” button on the controller for more than 4 seconds. The LED light will remain on. Release the learning button and press the “” button on the remote control at the same time. Wait until the LED light flashes twice and the buzzer sounds twice. At this point, the “” button learning is complete; Then press and hold the “” button on the controller for more than 4 seconds, and the LED light will remain on. Release the learning button and press the “” button on the remote control at the same time. Wait until the LED light flashes twice and the buzzer sounds twice, at which point the “” button learning is complete.
   Note: The “” and “” keys are learned separately; The “□” key can be controlled without learning. After powering on, the LED indicator light remains off. Regardless of whether manually or remotely operated, the LED light flashes once and the buzzer sounds once. The manual function and remote control function are interrelated and controlled.

V. Clearing method:

After ensuring the correct connection of the power cord, the power on LED will remain off. Press the “□” button for more than 8S, the LED will flash twice and the buzzer will sound twice. At this point, the code clearing is complete. After clearing, the remote control that was previously learned to code will no longer be controlled.

VI. Attention:

1. The bottom plate is charged, please do not operate with it. The power should be turned off for operation, and after confirming that there are no errors, it should be powered on for use.
2. If the motor does not work after installation, the direction line can be swapped for a trial
3. When the voltage of the remote control is insufficient, please replace the battery in a timely manner (when the voltage of the remote control battery is insufficient, the distance of the remote control usually becomes closer).
4. When using wireless electronic products, attention should be paid to avoiding metal masks, large electronic devices, electromagnetic fields, and other sources of strong interference, to prevent the remote control from having a short distance from the receiver or not working properly.
5. Do not use this electronic product abnormally. Abnormal use can reduce product performance and lifespan, and in severe cases, it can damage the product and pose a safety hazard to you.