GAMWING-logo

GAMWING AB01 Telescopic Mobile Phone Game Controller

GAMWING-AB01 -Telescopic -Mobile-Phone -Game-Controller-product

Product Introduction

GAMWING-AB01 -Telescopic -Mobile-Phone -Game-Controller-fig (1)GAMWING-AB01 -Telescopic -Mobile-Phone -Game-Controller-fig (2)

Product Layout

GAMWING-AB01 -Telescopic -Mobile-Phone -Game-Controller-fig (3) GAMWING-AB01 -Telescopic -Mobile-Phone -Game-Controller-fig (4)

Connection and power on

Follow these steps to connect your phone to the controller.

GAMWING-AB01 -Telescopic -Mobile-Phone -Game-Controller-fig (5)

* The indicators will be solid light on to Indicate a successful connection.
* Some Android phones may need to be enabled OTG to power on and use the controller.

Standby and Wake-up

  1. When the controller is turned on with 10 minutes of inactivity, it enters standby mode.
  2. When the controller is turned on, holding the H button for 10s can enter standby mode.
  3. When the controller is in standby mode, pressing H/A/B/ X/Y button can wake up the controller.

Mode InstructionGAMWING-AB01 -Telescopic -Mobile-Phone -Game-Controller-fig (6)

Calibration Of Joystick And Triggers

  1. Power on the controller or connect it to your phone, hold the View+Menu+H combination buttons for 5 seconds till the indicator lights blink white rapidly to enter calibration mode.
  2. Ensure the triggers and the joysticks are in their natural position without any contact.
  3. Rotate the joysticks at their maximum travel 3 times and let them return to the initial position naturally.
  4. Press the triggers to their maximum travel 3 times and let them return to their initial position naturally.
  5. Press the A Button to complete and exit the calibration mode.

Note:

  1. Calibration should be kept at a constant speed and gently operated to avoid errors in the collected data.
  2. If the joysticks and triggers can be used normally, please do not calibrate.

Back Button settings

can be mapped to

A/B /X/Y/ LB/RB / LT / RT / LS / RS / D-PadGAMWING-AB01 -Telescopic -Mobile-Phone -Game-Controller-fig (7)

Set the L4/R4 value:

  1. Hold the M+L/4 buttons combination buttons for 3 seconds till the indicators blink white slowly.
  2. Press the button you want to map to L4/R4.
  3. Press M button to finish the setting, the indicators return to the initial state. The L4/R4 buttons value is set.

Cancel the L4/R4 value:

  1. Hold the M+L4/R4 combination buttons for 3 seconds till the indicators blink white slowly.
  2. Double-click the button L4/R4.
  3. The indicators return to the initial state. L4/R4 button value is canceled.

Note:

After 30 seconds of inactivity when setting, the controller will automatically exit the setting mode and the button value will remain the same.

Button Combinations

GAMWING-AB01 -Telescopic -Mobile-Phone -Game-Controller-fig 8

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

RF warning statement:

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Documents / Resources

GAMWING AB01 Telescopic Mobile Phone Game Controller [pdf] Instruction Manual
2BKK3-AB01, 2BKK3AB01, AB01 Telescopic Mobile Phone Game Controller, AB01, Telescopic Mobile Phone Game Controller, Mobile Phone Game Controller, Phone Game Controller, Game Controller, Controller

References

Leave a comment

Your email address will not be published. Required fields are marked *