GALLERY L800 DTF Printer User Manual

GALLERY-LOGO

GALLERY L800 DTF Printer

GALLERY-L800-DTF-Printer-PRODUCT

Overview Of Main Components

GALLERY-L800-DTF-Printer-FIG- (1)

Front Left Control Panel
The front left control panel has five buttons:

GALLERY-L800-DTF-Printer-FIG- (2)

  1. POWER – turns on power to the printer section. Solid Green = Ready, Blinking Green = Busy
  2. INK BUTTON – Initiates a head cleaning cycle.
  3. END JOB – Press at the end of a job, or press during a job to cancel a job in progress.
  4. ENTER (REVERSE) – pulls film back into the printer.
  5. EXIT (FORWARD) – pushes the film forward out of the printer.
    Note: The Green front panel Power LED must be ON whenever the PC wants to communicate with the printer

Front Right Control Panel

GALLERY-L800-DTF-Printer-FIG- (3)

  • SET – Used when you want to set the target temperature (40 degrees Celsius is the default).
  • PLUS (+) – Increases the target temperature.
  • MINUS (-) – Reduces the target temperature.
  • NET – Not currently used

Overview Of Main Components (Continued)

GALLERY-L800-DTF-Printer-FIG- (4)

LED To Monitor White Ink Circulation
The front left side of the printer has an LED to show the ink circulation status.

  • BLUE = All parts of the ink circulation system are active and functioning correctly.
  • Blinking shows that head cleaning is actively occurring.
  • As long as this LED does not show RED, you know that the ink circulation system is fully functiona.l

Back Of The Printer

GALLERY-L800-DTF-Printer-FIG- (5)

The back of the printer has a USB port to connect to a Windows PC, the main printer power switch, and the auto ink priming button. The main power switch should always be left ON so that automatic ink circulation can occur. The auto-ink priming button (with an ink icon) avoids the need for needles.

Press and hold 5 seconds to pull ink through the lines when loading ink for the first time. The back of the printer also has screw holes to attach the film roller and holes for the waste ink bottle. Note that the screws needed to attach rollers are already attached to the printer. Remove and reattach these screws when attaching the roll holders.

  • Waste Ink Bottle
  • Auto-Ink
  • Priming Button
  • Main Power USB Port Switch

Right Side Of Printer
The right side of the printer has refillable ink tanks and an Auto-ink-priming button. (For some models this button may be on the back of the printer.) The Auto-ink-priming button avoids the need for needles. Press and hold to pull ink through the lines when loading ink for the first time.

Step 1
Remove the zip tie next to the printhead.

GALLERY-L800-DTF-Printer-FIG- (5)

Step 2
Attach the waste ink bottle holder to the back of the printer. Attach empty bottle to waste ink line.

Step 3
Screw the left and right film roller brackets to the back of the printer.

GALLERY-L800-DTF-Printer-FIG- (7)

Step 4
Attach one of the flanges to the film roller bar, place the film on the bar, then attach the second flange. Adjust the position of the film on the roller bar so that it loads into the printer straight and does not pull to one side.

Setting Up Your Gallery L800 DTF Printer (Continued:)

Step 5
Cut the film edge to be exactly perpendicular to the film sides so that the film will feed straight.

GALLERY-L800-DTF-Printer-FIG- (7)

Step 6
Place the film into the printer and press the Exit (Forward) button on the front control panel to pull the film through the printer. Observe that the film is moving through the printer without drifting to one side or the other. Straight feeding of the film is essential to printer operation.

GALLERY-L800-DTF-Printer-FIG- (8)

Step 7
Before loading ink into the printer, please install the software and run a blank test job to verify that no circuitry or connections were damaged during shipping. Operating the printer for a short period withouinkks will not harm the printer.

GALLERY-L800-DTF-Printer-FIG- (9)

SEE THE NEXT PAGE FOR SOFTWARE SETUP

Setting Up The PC Software (Windows 10/11)
GALLERYCARD-091123
THIS IS YOUR GALLERY DTF RIP SOFTWARE ACTIVATION KEY

TO ACTIVATE YOUR SOFTWARE

  1. Go to www.galleryprinters.com/downloads
  2. Click on the “Download Software” button to download and install the software.e
  3. During installation, you will be prompted for the Activation Code and registration information on
  4. When the registration window opens, click “Enter activation code”.
  5. Enter your code and customer information. Follow the on-screen prompts.
  6. You will require this code whenever referencing your product with the manufacturer or dealer you purchased it from.

ACTIVATION CODE
P1234 5678 9012 34

Step A
Find the card in the printer box with the download link for the software and your software activation code.

GALLERY-L800-DTF-Printer-FIG- (10)GALLERY-L800-DTF-Printer-FIG- (11)

Step B
Download and install the Gallery DTF RIP software, and select Gallery L800 printer (Make sure the USB cable is attached and the printer front power LED is Green).

Step C
During installation, select EPSON L800 as the communications port. (This is what Windows calls the Gallery L800 printer).

Step D
Under the HELP menu, activate your software using the license key number on the card in the printer box. You can watch a video of the full software download/install sequence at the following link: galleryprinters.com/videos. Continue To the Next Page To Complete the Gallery L800 Printer Setup.

Setting Up Your Gallery L800 DTF Printer Continued

Step 8
Once the software is installed, load a test file and try to print it. Observe that the printhead moves back and forth many times, the film advances and the front control panel blinks green while printing and goes solid green shortly after printing ends.

GALLERY-L800-DTF-Printer-FIG- (12)GALLERY-L800-DTF-Printer-FIG- (13)

Step 9
Shake ink bottles vigorously. Pour ink into ink tanks using funnels (right side ofthe printer). Press/hold the auto-ink-priming button to feed ink through lines.

Step 10
Your initial print may require 2 or 3 head clean cycles to fully prime the printhead. Print a nozzle check and a few small test jobs to be sure all colors are present.
Note: This image can be downloaded at galleryprinters.com/manuals

Frequently Asked Questions

Q: How do I get black text in my design to print white?
A: Select the White mode code from the pull-down menu under the work area in the DTF RIP software.

Q: How do I avoid white pixels from showing at the edges when pressing onto a black T-shirt?
A: In the RIP software, press the Color Adjust button under the work area and set choke to a higher value. Note that both Cold Peel and Hot Peel printmodes have already been pre-set to a choke value of 3 which is ideal. For White Only and Black Cut/Add Raster Holes print modes, the choke value is set to 0 as the ideal starting value.

Q: How do I get my colors to be more vivid?
A: In the RIP software, press the Color Adjust button and increase the Saturation slider value.

Q: How long should I wait after printing before adding the powder?
A: You can add powder as soon as the white ink is not pooling and the ink appears sticky, not runny. If you print large contiguous areas with pooling white, you may have to wait several minutes, otherwise you can powder almost immediately.

Q: Once cured, how long will a DTF print last before it needheat-pressed seeddd onto a garment?
A: Prints properly stored should be able to be used up to a year from when they were created.

Q: What is the shelf life of the inks?
A: CMYK inks perform best when used within 9-12 months. Gallery bottles show date information. White ink performs best when used within 6-9 months. Gallery bottles show date information.

Q: Is it necessary to print white under every pixel or can I avoid white ink when printing on white T-shirts?
A: The powder will stick and cure to the colored inks, but the wash life cycle of the garment will be lessened without white ink. Additionally, the white ink allows the design to stretch – depending on your garment and design, stretchability may be desirable.

Q: Can I add powder while the film is still on the printer exit tray?
A: NO! This poses a risk of powder getting onto the printhead. Always powder well away from the printer.

Q: What is the wash lifetime of a DTF print?
A: A properly printed, cured, and applied Cold Peel DTF print should last up to 50 washes. Hot Peel typically lasts 40 washes.

Q: How do I get a softer hand feel to my prints?
A: Use less white ink (note that less ink reduces the wash lifetime). Use the Black Cut, Add Raster Holes print mode in the DTF RIP software. Using the Cold Peel or Hot Peel printmodes, use a Production Plug-in called Rasterization.

Q: How can I get more White ink onto my prints?
A: Copy and Rename a print mode (eg. Cold_Peel to MaxWhite_Cold_Peel) and then edit the new print mode ColorLayer->ProcessingOptions to increase Underbase and Maximum Ink percentages. Note that increasing White may impact soft hand feel.

Troubleshooting

Printer Will Not Print. Check that both the rear power switch and front panel Green LED printer power switches are ON. On the Windows PC, check under Settings->Devices->Printers&Scanners that EPSON L800 is not Offline.

In Gallery DTF RIP software, check under Devices->Manage_Devices->Device_Properties that the Gallery L800 port shows EPSON L800. With the above checked, in the RIP software, try running a head clean to see if the printer responds.

Red LEDS Flash In An Alternating Fashion
This indicates that the waste ink counter has reached its maximum limit. In an upcoming release of Gallery DTF, the counter will be reset within Gallery DTF RIP software under Devices->ManageDevices->DeviceProperties->ResetInkWastePadCounter. It is also possible to use an external program, please contact your distributor for assistance.

Red LEDs Flash Simultaneously
This represents an error. The most likely cause is that the encoder ribbon cable has dust that needs to be cleaned. Errors can sometimes be cleared by powering off for 10 seconds while the carriage is in the middle. Power on causes a new self-test. You can contact USA-based support to assist in reading the error code or cleaning the ribbon cable.

Red Ink LED Comes On Solid
This means that one of the ink channels is starved for ink. In most cases, this condition will clear itself and printing will continue. A short single press will clear the black channel, otherwise a short double press will clear the other color channels. Press/hold the front ink button to initiate a head-cleaning.

One Of My Colors Is Not Printing, Or White Ink Is Not Printing Correctly Check to see that the ink lines feeding the printhead do not have any air gaps. Press the auto-priming button. Perform a couple of head cleanings. Print a nozzle check. If the nozzle pattern does not look complete for one or more colors, perform additional head-cleaning cycles.

Note that performing too many head cleanings in a row can cause foaming which adds air. Pause 5-10 minutes between every 3 head cleanings. The Film Advances And Retreats When I Am Not Printing Anything. This is normal. The printer needs to advance the film to expose the squeegee when auto-cleaning the printhead.

Congratulations On Your Purchase Of The Gallery L800 DTF Printer. To get maximum benefit from your printer, please familiarize yourself with the printer and its functions.

Documents / Resources

PDF thumbnailL800 DTF Printer
User Manual · L800 DTF Printer, L800, DTF Printer, L800 Printer

References

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.