Sonraíochtaí
- Sruth leictreach: 10 A
- sruth á athrú: 10 A
- Momentary contact current: 250 V
- Imltage: Rátáilte voltage
- Suiteáil: Gléasta flush
- Rialuithe agus táscairí: Number of buttons – 0, With feedback signal contact – No
- Ábhair: Miotal, Plaisteach
- Cóireáil: Gan chóireáil
- Nascacht: Type of connection – Screw terminal
- Toisí: Depth – 42 mm, Built-in depth – 31.30 mm, Built-in depth flush-mounted boxes – 35 mm
- Sábháilteacht: Impact resistance IK – IK07, Ingress Protection (IP) class – IP44
- Téacsanna: Imprint – Without imprint, Installation mode – For screw fastening, Switch mode – Change-over contact, usable as NC or NO, Type of connection – With screw terminals
- Related Series: Berker B.3, Berker B.7, Berker K.1, Berker K.5, Berker Q.1, Berker Q.3, Berker Q.7, Berker R.1, Berker R.3, Berker R.8, Berker S.1 Berker K.x, Berker Q.x, Berker R.x, Berker S.x/B.x
Change-over switch for lock cylinder
Ordú uimh. 3836 20
Change-over switch 2-pole for lock cylinder
Ordú uimh. 3826 10
Push-button for lock cylinder
Ordú uimh. 3856 20
Switch the blinds for the lock cylinder
1 pole, order no. 3831 20
Switch for blinds 2-pole for lock cylinder
Ordú uimh. 3822 10
Push-button for blinds for the lock cylinder
- Ordú uimh. 3831 10
- With Earth contact, order no. 3831 20
Push-button for blinds 2-pole for lock cylinder
Ordú uimh. 3832 10
Treoracha sábháilteachta
Electrical equipment must only be installed and assembled by qualified electricians. Failure to observe these instructions may lead to damage to the device, fire, or other hazards.These instructions are an integral component of the product, and must be retained by the end user.
Feidhm
Key switches/key push-buttons are used to prevent unauthorised operation of the connected loads. These devices are intended for the installation of profile half cylinders according to DIN with a length of 40 mm. Recommendation: use a profile half cylinder with an adjustable lock bit to allow adaptation of the locking characteristics to various requirements.
Suiteáil
Adjusting the lock bit on the profile leathsorcóir
The lock bit position of some profile half cylinders (Berker: order no. 1818..) can be changed in 45° increments when the key is removed (Figure 1). To change the switching position, the lock bit can be guided in the fork (1) of the switch/push-button insert, or can contact the fork laterally (2) (Figure 2). The switching positions in which the key can be removed depend on the lock bit position of the profile half cylinder being used. If the lock bit is guided in the fork, it can only be removed in one switching position (overview in the appendix). Furthermore, the lock bit position determines whether the cover can be removed with the lock cylinder without the key, or whether it is protected against removal by the cover plate (antidismantling protection). The cover is secured in the lock bit settings 90°, 135°, 22,5°, and 270° (Figure 3). Cuir an locking pin into the lock bit from the side and move the lock bit to the desired position. (Fíor 4)
Installing the profile half cylinder in the centre plate
The lock bit on the profile half cylinder is adjusted.
- Using key, move lock bit on profile leath cylinder (4) to 180° position and guide it through the centre plate (5) from the front (picture 5).
- Connect lock cylinder and centre plate using an scriú glasála (6).
Connecting and mounting the key switch
CONTÚIRT!
Electrical shock when live parts are touched. An electric shock can lead to death: Isolate from mains voltage roimh nascadh.
The key switch/key push-button is intended for installation in a connection box according to DIN 49073, Part 1 with screw fastening.
- Connect the switch insert/push-button insert on the rear according to the labelling.
- Position switch insert/push-button insert (8) in the connection box (7) and screw in place. Note marking TOP/OBEN. (Bild 6)
- Fit frame (9) on the switch insert/push-button insert.
- Using the key, move lock bit into position, fit centre plate and profile half cylinder (10) and screw in place. Depending on requirements, guide the position of
the lock bit in or next to the fork of the switch insert (see “Adjusting the lock bit on the profile half cylinder) - Bain an eochair.
- Snap-on cover (11) for the profile leathsorcóir
Aguisín
Tharview: Switching positions of key switches with a removable key (Figure 7)
|
Switch orderno |
Lockbitposition, key removable |
Switching behaviour, key removed |
| 3821. .
3822. . |
 |
 |
|
3826. . 3836:: |
         |
         |
Sonraí teicniúla
| Ordú uimh. | Sruth á athrú | Oibriúcháin voltage |
| 382120 | 10 AX
(100WLED(SBL)) |
250V~ |
| 382210 | 10 AX
(100WLED(SBL)) |
250V~ |
| 382610 | 16 AX
(200WLED(SBL)) |
250V~ |
| 383110 | 10A | 250V~ |
| 383120 | 10A | 250V~ |
| 383210 | 10A | 250V~ |
| 383620 | 16 AX
(200WLED(SBL)) |
250V~ |
| 385620 | 10A | 250V~ |
Gabhálais
Profile leathsorcóir
- With differing closure, 1818
- With the same closures 1818 01
Bharántas
Coimeádaimid an ceart chun athruithe teicniúla agus foirmiúla a dhéanamh ar an táirge ar mhaithe le dul chun cinn teicniúil. Tá ár gcuid táirgí faoi ráthaíocht laistigh de raon feidhme na bhforálacha reachtúla. Má tá éileamh baránta agat, déan teagmháil leis an bpointe díola le do thoil.
Berker GmbH & Co.
KG Zum Gunterstal 66440 Blieskastell/Germany
Teil.:+49 6842 945 0
Facs:+49 6842 945 4625
R-phost: eolas@berker.de
www.berker.com
CCanna
C: An féidir an táirge seo a úsáid lasmuigh?
A: The product has an IP44 rating, making it suitable for outdoor use where it will be protected from direct exposure to the elements.
Q: How many buttons does this product have?
A: This product does not have any buttons.
Doiciméid / Acmhainní
 |
hager 385620 Key Push Button [pdfLámhleabhar Úinéara B.3, B.7, K.1, K.5, Q.1, Q.3, Q.7, R.1, R.3, R.8, S.1, K.x, Q.x, R.x, S.x-B.x, 385620 Key Push Button, 385620, Key Push Button, Push Button, Button |