FX-AUDIO- DA06 Operating Panel
Product Specifications
- Brand: Linkx
- Model: TG-500ST
- Frequency Range: UHF 500 – 937.5 MHz
- Power Input: 12V DC, 1.2A Max
- Impedance: 50 Ohm
- Dimensions: 215(W) x 157(D) x 43(H) mm
- Weight: 682 g
- Enclosure: Black half-rack metal housing
Product Usage Instructions
Power Switch
To turn the TG-500ST on, press the power button. The display will illuminate, indicating the system is in ON/operational mode. Press the power button again to turn the TG-500ST off.
AF Input Volume Control
Turn the knob to adjust the volume. Rotating it fully counterclockwise will mute the audio volume.
AF L(I)/R(II) Balance Control
Adjust this knob to set the audio balance of the transmitted signal when two separate audio sources are connected to AF input L(I)/R(II). Turn left or right to choose the source you want to transmit.
OLED Screen
The TG-500ST features an OLED screen for visual display.
Headphone Output
Connect headphones to the 3.5mm jack with volume control for monitoring audio.
Menu Button
Use the menu button for easy navigation through the system settings.
Overview of the Operating Panel
Front Panel
A Power switch
- Display is illuminated: System in ON / operational mode
Press the power button to turn the TG-500ST on. When display is illuminated, it indicates system is ready to use. Press the power button again to turn the TG-500ST off. - AF input volume control
Turn the knob to adjust volume. Knob fully counter-clockwise will MUTE the audio volume - AF LL/R(Lbalance control
Turn the knob left or right to set the audio balance of the transmitted signal- When two separate/different audio sources are connected to AF input LI)/RII) on the rear panel, adjust this knob to choose the source you like to transmit.
- Turn the knob left increases the audible volume of the AF L (I) channel and Turn it right increases the audible volume of the AF R (II) channel
- OLED screen
- Headphone output 3.5mm jack with volume control for monitoring
- Menu button
- Easy to use menu navigation button
Rear Panel - DC In 15V 1.6A
- 5V charger output / Engineering service interface for product maintain and software update
- Multiple transmitters network loop connection
- AF input sensitivity level switch (Aux / Line level switchable)
- Audio output / Loop out / Balanced, 6.3mm jack
- Audio input / Balanced, XLR & 6.3 combo
- RF Antenna output, BNC socket
- Connect standard dipole antenna AN0510-5501BBN
- Connect Directional Log Antenna ANTIOOWD with Antenna Booster AB-OI UHF enhances signal transmission. Ideal for increasing operation range and reducing reliability concem from outside interference
Related products
ANT-IWND Directional UHF antenna AB-OI UHF Antenna Booster eTour Digital UHF tour guide system TG-500T: portable transmitt+ portable receiver
- AB-01UHF Antenna Booster maybe used to compensate for RF loss associated with long coaxial cable operation. But be careful to avoid overloading the RF signa
- Prepare a standard tripod, microphone stand or other ceiling mount bracket, and a sufficient length of terminated coaxial cable if using ANT-100WD.
Power switch
- Power switch
- RF Input (1~4) LED Indicators
When the stationary transmitter is powered on and its RF output is connected to the ACR4 input, the corresponding RF input LED on the front panel of the ACR4 will light in blue.
12V DC, 1.2A Max Power Input
ACR4 4port Antenna Combiner Specification
- ACR4 4-Port Antenna Combiner
- Frequency Range: UHF 500 – 937.5 MHz
- Gain: 0 dB ± 2.5 dB
- Max Input Power: 10 dBm (10 mW)
- Intermodulation Attenuation: -50 dBc
- RF Input: 4 × BNC (Female)
- RF Output: 1 × BNC (Female)
- Impedance: 50 Ω
- Power Supply: DC 12V, 1.2A
- Dimensions: 215 (W) × 157 (D) × 43 (H) mm
- Weight: 682 g
- Enclosure: Black half-rack metal housing
Multiple-Channel Wireless Interpretation / Monitor System DC In 15V 1.6A
- 5V charger output / Engineering service interface for product maintain and software update Multiple transmitters network loop connection AF input sensitivity level switch (Aux / Line level switchable) The ACR 4 is a broadband 4 RF input port antenna combiner designed to connect up to four transmitters to create large multi-channel systems. It operates over an ultra-wide frequency range of 500 to 937.5 MHz with four BNC RF inputs, one BNC RF output and four
- RF input blue status indicator LEDs. A 50 ohm load connector is attached to each RF input for use with no antenna input to prevent unwanted radio interference noise. ACR 4 greatly improves the transmission quality, reduces intermodulation distortion and signal loss due to multipath interference. The ACR 4 is compatible with the Linkx wireless fixed transmitter TG-100ST/200ST/ 300ST/288ST/500ST.
- The ACR 4 features a black, rugged, half-rack metal enclosure. The optional rack mount bracket kit allows you to mount one or two ACR 4 combiners into the 1 RU space of any standard 19-inch equipment rack.
Note: If there is no signal coming at the input, be sure to connect the included 50 ohm load connector to the BNC socket to prevent unwanted radio interference noise.
Installation and Setup
Connect the Powerl Adaptor
Only use the power adaptor supplied to ensure safe operation. Plug power supply into TG-500ST and power cable into AC wall socket.
Briefly press the power button, the receiver switches on and the display illuminates.
Connect the Headphone
- To avoid permanently damaging your ears with extremely loud volume, turn the volume knob of the headphone to fully counter-clockwise (the minimum sound level ) before wearing your headphone.
- Connect the headphone with 3.5mm jack and monitor the contents
- Wear the headphone and gradually turn up to reach your desired volume
AB-01UHF Antenna Booster + ANT-100WD Directional Log-Periodic Antenna
Condition: Cable length exceeds 10 meters
- Prepare a standard tripod, microphone stand or other ceiling mount bracket, and a sufficient length of terminated coaxial cable if using ANT-100WD.
TG-SOOST parameter setup
- Use the AB-01UHF antenna booster to compensate for signal loss during long coaxial cable operation
- Set the RF power setting on the stationary transmitter to the appropriate level (it is recommended to start from the “Low” level) to avoid RF signal overload.
FAQs
Q: Can I use the ACR 4 Antenna Combiner with other transmitters?
A: The ACR 4 is compatible with Linkx wireless fixed transmitters TG 100ST/200ST/300ST/288ST/500ST.
Q: How many transmitters can be connected to the ACR 4?
A: The ACR 4 can connect up to four transmitters to create large multi-channel systems.
Documents / Resources
 |
FX-AUDIO- DA06 Operating Panel [pdf] Instructions DA06 Operating Panel, DA06, Operating Panel, Panel |