Fusion ARX70B ANT Wireless Remote-Complete Features/Instruction Guide

It is ANT marine remote control. It is IPX6 and IPX7 water-resistant and UV stable with built-in ANT technology. It works with ANT-enabled Fusion maritime radios. It Allows for single-zone control. For multi-zone control, use several ARX70s. Its Mounting is simple and quick.

REMOTE OVERVIEW

	Radio sources: Press to tune to the previous station. Other sources: Press to skip to the beginning of the track or to the previous track.
	Radio sources: Press to tune to the next station. Other sources: Press to skip to the next track.
	Press to decrease the volume. Hold to quickly decrease the volume.
	Press to increase the volume. Hold to quickly increase the volume.
and	Press both keys to enter zone selection mode (Selecting a Zone, page 1).
	Press to cycle through the available sources. Hold to pair with a stereo (Connecting the ARX70 Remote to a Stereo, page 1).
	Radio sources: Press to mute or un-mute. Other sources: Press to pause or resume.

STATUS LEDS

Green short blink	Transmission successful
Green long blink	Pairing or zone selection successful
Green flashing	In zone selection mode
Green and red flashing	In pairing mode
Red short blink	Transmission failed
Red long blink	Pairing or zone selection failed
Orange flashing	Attempting to transmit; check the stereo

CONNECTING THE ARX70 REMOTE TO A STEREO

For a list of compatible stereos, go to www.fusionentertainment.com/marine/products/remote-controls/MS-ARX70B/specs.

Bring the ARX70 remote within 10 m (33 ft.) of the compatible stereo.
NOTE
Stay 10 m (33 ft.) away from other ANT® devices while pairing

Place the stereo into Bluetooth® discoverable mode.
For detailed information, see the stereo owner’s manual at www.fusionentertainment.com/marine.
On the ARX70 remote, press and hold ARROW button until the status LED starts alternating green and red.
The remote searches for the stereo. When the remote pairs successfully, the status LED turns on green briefly and then turns off.
If the remote cannot find the stereo, the status LED turns on red briefly and then turns off.

MOUNTING CONSIDERATIONS

NOTICE

Selecting the correct mounting location is critical to optimize the performance of the remote control.

You must mount the remote control in a location that is within 10 m (33 ft.) of the stereo.
You must mount the remote control in a location where it is not submerged.

If you need to mount the remote control outside the boat, you should mount it in a location where it will not be damaged by docks, pilings, or other pieces of equipment.
You should select a flat mounting surface for the best results.

The mounting surface must be free of dirt, debris, wax, or coatings.
After you select the location, hold the remote control in the selected location, press a few buttons, and confirm the operation on the stereo.

Move away from sources that can interfere with the remote control’s operation. Sources of interference may include strong electromagnetic fields, some 2.4 GHz wireless sensors, high-voltage power lines, electric motors, ovens, microwave ovens, 2.4 GHz cordless phones, and wireless LAN access points.

MOUNTING THE REMOTE CONTROL

Before mounting the remote, you must connect the remote to the stereo.

Select an appropriate location for the remote control (Mounting Considerations, page 1).
Thoroughly clean and dry the mounting surface using a mixture of water and isopropyl alcohol.
The mounting surface must be free of dirt, debris, wax, or coatings.

Test the range at the selected location by holding the remote at the location, pressing a few buttons, and confirming the operation.
Place the remote control on the mount, and rotate the remote until you hear a click.
Remove the backing from the adhesive.
Carefully orient the remote control in the mount with the FUSION® logo at the bottom.

NOTICE
Before placing the adhesive on the mounting surface, make sure the location and orientation are correct. It is extremely difficult to remove the adhesive. Some mounting surfaces might be damaged after removing the adhesive.

Press the remote control firmly onto the mounting surface, maintaining pressure for at least 60 seconds.
Allow the remote control to sit at room temperature for 72 hours.

SELECTING A ZONE

On compatible stereos, you can use the ARX70 remote control to select a zone and change the volume of the zone. Some stereos require a software update to enable this functionality of the remote.

NOTE
When you connect to a stereo, all zones are selected by default.

Press – and + to enter zone selection mode. The status LED begins flashing green.
Press a button to make a selection:

Press REWIND button for zone 1.
Press FORWARD button for zone 2.
Press – for zone 3.
Press + for zone 4.
Press ARROW button for all zones.
Press PLAY/PAUSE button to cancel the zone selection.

When a zone is selected successfully, the status LED turns on green briefly and then turns off. When zone selection fails, times out, or is canceled, the status LED turns on red briefly and then turns off.

NOTE
When you select an inactive or invalid zone, the remote still functions but does not control the volume. You can select to select all zones.

REPLACING THE BATTERY

The remote uses one CR2032 lithium coin-cell battery.

Rotate the remote control, and remove it from the mount.
Rotate the battery compartment counter-clockwise until the line points to .
Wrap the end of a small flat screwdriver with tape.

The tape protects the battery, battery compartment, and contacts from damage.

Carefully pry the battery from the battery compartment.

Insert the new battery into the compartment with the positive side facing down.

NOTE
Do not damage or lose the O-ring gasket.

Align the battery compartment in the remote control so the line points to .

Press the battery compartment down into the remote control, and rotate the compartment clockwise until the line points to .
Make sure the battery compartment is fully seated in the remote control.
Place the remote control in the mount, and rotate until it clicks.

TROUBLESHOOTING

The remote will not connect to the stereo

Make sure the stereo is in Bluetooth discoverable mode.
Move closer to the stereo, and attempt to connect to it again.

Disable Bluetooth discoverable mode on the stereo, and then re-enable it.

THE LED DOES NOT LIGHT WHEN I PRESS A BUTTON

The battery is low or dead or is installed improperly. Replace the battery.

THE LED IS ONLY RED OR ORANGE WHEN I PRESS A BUTTON

Move closer to the stereo, and attempt to connect to it again .

Before mounting, make sure you have selected an optimal location for the remote.

THE REMOTE DOES NOT CHANGE THE VOLUME, BUT OTHER FUNCTIONALITY WORKS

An invalid zone is selected. Select a zone valid for the stereo.

Frequently Asked Questions

What’s the best way to pair a fusion remote?
These are the buttons on the wired remote control that comes with the package. To turn on the stereo, press the button. To turn off the stereo, swiftly press the power button. To pair with a Bluetooth device, hold for 5 seconds.

What is the best way to connect my fusion radio to my phone?
Search for Bluetooth devices on your suitable Bluetooth device. Select the RA60 stereo from the list of identified devices on your compatible Bluetooth device. Follow the on-screen directions to link and connect to the found stereo on your compatible Bluetooth device.
What is the purpose of fusion link?
Navigate all music sources, adjust individual volume zones, and operate entertainment systems that are all linked to the same Wi-Fi network. Albums, artists, and playlists may all be navigated with the same ease as the Fusion marine interface. The artwork for the album is displayed on the screen (Wi-Fi only).
What is the procedure for resetting my Bluetooth Fusion?
Remove any previously paired devices from the unit and the mobile device.
Carry out a factory reset on the device (see below links for reset instructions)
Both devices should be rebooted or cycled.
Re-pair: If the issue is addressed, no further action is required.

What’s the best way to keep my Fusion up to date?
Wait for the unit to recognize the drive by pressing the ‘source’ key and cycling to the ‘USB’ source. Finally, pick ‘Settings’ from the ‘Menu’ key, then ‘Update.’ Choose ‘Head Unit’ from the drop-down menu.
What’s the best way to keep my Fusion up to date?
Check to see if your gadget is fully charged and connected to the internet.
Select Settings from the Notification bar by swiping down.
Select Software Update from the drop-down menu, then Check for Updates.
To download and install the update, follow the on-screen instructions.
How can I figure out which Fusion 360 version I have?
To determine which Fusion 360 version is in use, perform the following steps:
In the upper right corner of the screen, click the Question Mark icon.
To learn more, go to About.

Is Fusion a reputable brand?
Fusion does not place a high value on its personnel. Management is poor; they do not assist their staff, which is a vital part of management in order to promote growth and success.
Is it possible to programme any remote to work with any television?
The good news is that every TV sold today can be controlled with a universal remote. You could buy a device-specific remote from your TV maker to replace your TV’s remote, but this could be costly and unnecessary.
Why isn’t my SYNC working?
Try turning off your phone, resetting it, or removing the battery, and then attempting to use it again. Try removing your device from SYNC and then reinstalling SYNC on your device. Always double-check the security and auto-accept prompt settings on your phone’s SYNC Bluetooth connection.

View Fullscreen

References

User Manual

Fusion ARX70B ANT Wireless Remote

Specifications

Introduction