funomo CS_1026J In Car Smart Carplay Screen Multimedia Player
Specifications
- Display: 10.26-inch FHD (1600 x 600)
- Camera: Two wide-angle cameras
- Interface: Touch control, Bluetooth, WiFi, FM Transmitter
- Recording: SD card recording
- Language Interface: Simplified Chinese, Traditional Chinese, English, Russian, Spanish, French, German, Japanese, Korean, Arabic, Italian, Portuguese
- Video Input: 2 channels of FHD video input
- Video Format: 4K H.264 video
Product Usage Instructions
- Installation
- Install the smart screen in your vehicle by fixing it onto the center console using the provided monitor screen base.
- Power Connection
- Connect the power cord to the Type-C power cord and plug it into the 12-24V input. The integrated cable allows you to take power from the cigarette lighter.
- Camera Setup
- Set up the backup camera and extension video cord according to your vehicle’s requirements. Ensure proper connection for optimal performance.
- TF SD Card Usage
- Insert a Class 10 High-speed TF SD card into the designated slot for recording and storage purposes.
- Functionality
- Operate the device using the touch screen interface. Utilize the different video input channels to view surrounding areas and record videos in high definition.
- Troubleshooting
- If you encounter any issues with the device, refer to the troubleshooting section in the user manual for assistance.
FAQs
- Q: How do I switch to the reversing screen?
- A: The device can automatically switch to the reversing screen when needed, ensuring you have a clear view while reversing your vehicle.
- Q: Can I review recorded videos on the device?
- A: Yes, you can locally playback recorded videos on the 10.26-inch HIGH-DEFINITION IPS screen at any time.
In-Car Smart Carplay Screen Multimedia Player User Manual
Warning: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: –Reorient or relocate the receiving antenna. –Increase the separation between the equipment and receiver. –Connect the equipment into an outlet on a circuit different. from that to which the receiver is connected. –Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Statement To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance of 20cm the radiator your body. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.
Product overview
The CS_1026Juses two wide-angle cameras installed inside and outside the vehicle to capture images of the surrounding area and transmit them to the integrated device in real time. With the help of this system, the driver can see the obstacles and pedestrians around the vehicle intuitively, and effectively to reduce the occurrence of scraping, collision, collapse and other accidents. Thisproductcan record all driving videos to avoid accidentfraud.
2
Package list
Name
Smart Screen
The power cord
Graphic
Introduce
10.26-inch FHD display (1600*600) / 2-
Quantity 1
channel camera interface / touch
control / Bluetooth / WiFi / FM
Transmitter /SD card recording /Power
harger with Type-C plug
1 Type-Cpowercord/12-24Vinput/ 5Voutput/ integratedcable/takepower from cigarette lighter
Backup camera
Extensi on
Video cord
Monitor screen base
AHD FHD (1080P/4PIN BMW Type)
Optiona l
About 6m/ 2.5mm headphone plug / 4PIN BMW type connector/double shield/with reverse trigger wire
Support the screen display,fix it ontothe center console
Optiona l
1
3
TF SD card
Aux cable
Class10 High-speed TF SD card Audio transmission line
Optional 1
Product description
Item System
Function introduction
Detailed description
Language Interface
SimplifiedChinese/TraditionalChinese/English/Russi an/ Spanish/French/GermaIJapanese/Korean/Arabic/It alian / Portuguese Graphical menu operation
Mode of operation
Video input
Video input
Video mode
Touch screen
2 channels of FHD video input Start recording video as soon as you turn on the device, without missing a second
The video format 4K H.264 video, separate storage for each channel video saved
Video display
Real-time display 10.26-inch HIGH-DEFINITION IPS screen, 1600 x 600
The playback Localplayback, available to review at anytime
Screensavercanbesetto several modes: The screen saver Off/10seconds/30seconds/1 minute Reversing display It can automatically switch to the reversingscreen
4
Reversing screen
Adjust rear view camera guidelines Adjust rear view camera guide lines
Wireless connection
mode
Wi-Fi
Supports Apple CarPlay and Android Auto
Bluetooth
Support Bluetooth music playback
FM
Support FM Transmitter
Video storage
TF SD card
CLASS-10 U1,Compatibility 32GB minimum and 256GB maximum
The microphone
Audio part
Voice control
Support microphone recording, you can turn it on/off
Support voice control, you can turn it on/off
Supports 12V-24V power voltage. There are Power part The power input power protection circuits
Power consumpt ion
Other
Two-way video Less than 10W (screen display, 2-channel camera recording)
Working temperature
The video time
-4°F to 149°F (-20°C to 65°C) Video recording duration can be set
camera mirroring
The camera supports mirror display
5
4. TF SD Card specification
The quality of the TF SD card has a great impact on the stability of video recording. To record videos safely, we recommend using SD cards from major brands such as SanDisk, Kingston, Toshiba and Samsung. The speed certification must be at least Class10.
Wiring instructions
The details are as follows
Port
Type-C power plug
Instructions Power supply port
Cigarette charger
Takes power directly from the cigarette lighter Note: The product comes with a special cigarette lighter charger. If you do not use our original charger, you need to buy a compatible highquality cigarette lighter charger. Otherwise, the device may be easily damaged due to insufficient voltage or other injuries may occur. In addition, the FM transmitter function will not work
7
normally.
Camera installation
Find the drilling hole, find the corresponding installation position in the license plate bracket, mark it with a pen, and then drill the screw hole of the corresponding size. Fix the camera to the rear of the car with screws. The reversing trigger cable (the red wire) needs to be connected to the positive pole of the reversing light. Finally, use the video extension cable to connect the camera to the screen.
(This is not necessary, if you choose the version without a reversing camera)
8
User Interface
1.Home button: return to home page 2.Brightness icon: adjust the screen brightness 3.Volume button: adjust the output volume 4.DVR: enter the video recording interface 5.Apple CarPlay: Especial driving interface for iPhone 6.Android Auto: Especial driving interface for Android mobile phones 7. Apple AirPlay: cast the iPhonescreen to the host monitor 8.Android Cast: cast the screen of an Android phone to the host monitor 9.Wi-Fi video: Follow the tips, connect to Wi-Fi 10.Audio output: Select the sound output mode 11.Playback: review a video recorded 12. Setting button: the setting interface
9
Apple CarPlay Firstly, turn on the WiFi and Bluetooth of your iPhone, then tap the [Apple CarPlay] button to enter the Apple CarPlay interface as shown. The Bluetooth of the device will be turned on automatically with the name T86-XXXX. Connect the Bluetooth to your iPhone and follow the iPhone’s instructions to open the app. After switching on, the device automatically tries to connect to the iPhone.
(Turn off Bluetooth and Wi-Fi of your iPhone to disconnect. The CarPlay option only supports Apple iPhone. 
For Android phones, please select the [Android Auto] option)
10
(Half-screenmode)
(Full-screenmode) Note: In the mobile phone dropdown menu, you need to turn off Bluetooth first and then turn off WiFi to disconnect Carplay. The device will still try to connect to the mobile phone if you only turn off your mobile phone’s WiFi.
11
Android Auto As shown in the figure, click the [Android Auto] button to enter Android Auto. Firstly turn on WiFi and Bluetooth of your android phone, and then select the [Android auto] option as shown in the photo, the host’s Bluetooth will automatically turn on, the name of the Bluetooth is T86-XXXXX. Connect the Bluetooth to your phone to open the application. When the host device is powered on, it will automatically attempt toconnect to the last connected phone
(Half-screen mode) 12
(Full-Screen Mode) 13
DVR
As shown in the picture, the main page will not directly display the camera image, you need to click the DVR button to enter DVR interface and view the camera video. When a TF SD card is inserted, the systemautomaticallyentersthevideomode.In the recordingmode,asmall red dot will flash.
Start/stop video Lock the video, then the video data will not bedeleted
Click to take a photo Return to main screen The wireless connected screen is displayed Turn on or turn off voice recording
14
Playback
As shown in the photo, click the [Playback] button to enter the video playback interface.
You can click on the playlist on the right to watchvideo or photo [Video] Video captured by front/rear cameras [Photo] Pictures taken by the front/rear cameras[Locked video] The protected video(s)
Click the[Delete] button to delete the item. Audio output
As shown in the photo, click the [Audio Output] button to enter the audio output selection interface.
15
(1) [Speaker]: The sound will be played through the device’sspeaker. 16
(2) [Bluetooth]: After selecting this mode [BT Audio], the Bluetooth transmission mode will beturned on. Turn on yourvehicle’s Bluetooth then, connect your cell phone’s Bluetooth to your car. After the car Bluetooth connection is successful, all the sounds of the device will be transmitted to your car speakers through Bluetoothtransmission.
After selecting this mode, the volume icon will change to the Bluetooth transmissionicon
[], and the volume cannot be adjusted on this device, it must be adjusted on
yourvehicle.
(3)[FM]: After selecting this mode, FM transmission mode will be turned on. For example, the FM transmitting frequency band of this equipment is set to FM106.0MHz(anyunoccupiedchannelcanbeused),tune yourcarradioto the same frequency FM 106.0 MHz,thenall sounds of the equipment will be transmitted to yourvehicle radio. Note: The sound transmission of FM modemay be interfered by radio clutter. Try a different FM frequency, if it doesn’t work well.
17
After selecting this FM mode, the volume icon will change to FM emission icon [ ], and the volume cannot be adjusted on this device then, it can only be adjustedon yourvehicle radio. (Using a non-original power cordwill weaken the FM Transmitter signal, the function cannot be used under some circumstances)
(4) [AUX]: After selecting this mode, the AUX output mode will be turned on. Connect the equipment to your vehicle’s AUX port with an AUX cable. After the connection is successful, set your car to be AUX-IN mode, then all the sounds of the equipment will be transmitted to yourvehicle speakers through the AUX cable. Afterselectingthismode,thevolumeiconwillchangetoAUX outputicon[ ],and the volume cannot be adjusted on this device, it can be adjusted on yourvehicle.
18
Setting As shown in the photo, click the [ ]icon to enter the setting interface.
19
Icon
Specification
Auto-dimming
Click to enter the [Autodimming]settings You can turn it off or on. Night brightness Settings. Enable time Settings
Screen saver
Click [Screen saver] to enter the settings. Screen saver can be set to:off / 10 seconds / 30 seconds / 1 minute. After entering the screen saver, you can click any place of the screen to resume the screen display.
Driving position
Click [Driving Position] to enter the setting. You can select left-hand driveor right-hand drive. On themenuof Apple CarPlay, you can choose it accordingly.
Click to enter the [Split screen mode] settings
Split screen mode
Split screen mode is only available for CarPlay and Android Auto
20
Assistive touch
Click to enter the [Assistive touch] settings
You can turn it on/off. Operation shortcut keys are available under this function
21
Icon
Specification
Click to enter the [Clear connections]settings
Clear connections
Clearconnection records with a cell phone (Bluetooth, Wi-Fi, Cast / MirrorLink)
Camera format
Click to enter the [Camera format] settings: A.720P B.720N C.1080P D.1080N
Record resolution
Clicktoenterthe[Recordresolution]settings
A.720P
B.1080P C. 2.5k D.
4K
Split time
Click[Splittime]toenterthesettingofthevideodurationtime
Video duration time is optional: 1 minutes / 3 minutes / 5 minutes The system default is”3 minutes”
Microphone
Click [Microphone] to enter the settings
You can turn it on/off. 22
Icon
Specicication
Click [Image mirror] to enter the settings: You can turn it on/off
Rear mirror image
Thisoptionmakesiteasierforcustomerstoinstalla reversingcamera flexibly.
Adjust guide lines of reversing mode.
Reverselinecalibratio n
Language
Click [Language] to enter the settings Available Language: Simplified Chinese / Traditional Chinese / English/ Russian / Spanish / French / German/ Japanese/ Korean / Italian / Portuguese
Tip sound
Click to enter the [Tip sound] settings You can turn it off/on
Voice control
Click [Voice Control] to enter the settings Available Voice control commands: show front camera / Show rear camera / Turn on display / Turn off display / Show all cameras.
5languageVoice
controlcommands.Afteropeningtheoption,inthe video
interface, say the corresponding command, the system 23
will perform the correspondingoperation. 24
Date and Time
Click on [Date & Time] to enter the settings Set up separately: year / month / day / hour/ minute / second / 12-Hoursystem / 24-Hour system
Storage info Format
Click to enter the [Storage info] setting
Click to view TF SD Card’s memory capacity
Click [Format] to enter the settings. This option formats all dataof the inserted SD Card. It is recommended to manually format TF SD card to ensure sufficient memory capacity and smooth recording, when you start to use the SD card at the first time. Note: We recommend that you format your SD card regularly.
Factory reset
Click [Factory reset] to enter the settings.By this operation, you can restore all settings to the initialones.
25
Firmware version
Click on [Firmware version] to enter the menu. This option is available in the current basic version for easy confirmation.
26
Parking Guide Lines Calibration Click [Reverse Line Calibration] to enter the settings
Park your car in the middle of the parking zone, manually hold and drag [ ], adjusttheposition of the reversing auxiliary line up, down, left and right, till the reversing auxiliary line reflects the actual and correct distance status. After adjusting the reversing line, click [confirm] to finish. Click [Cancel] to cancel settings and exit.
27
Troubleshooting
Item
Problem
Solution
(1)Check whether theplugs of the
Unable to power on the device
cigarette lighter power cord areconnected correctly and firmly.
(2)Check whether the power cord is at a
1
good shape and status. Avoid any
damage or unauthorized modification.
(1)Touch screen is unavailable during
2 The touch
power-on. Wait till the device enter the main interface, start to use touch screen.
screen doesn’t respond
(2)Check whether the touch isdamaged.Do not use sharp
objects on the touch screen, as this
can easily cause scratches and
damage to the touch screen.
28
3
The rear-
viewcamera
doesn’t work
(1)Buy and use themanufacturer’s rear-view camera, makesure plug and ports match.
(2)Make sure the camera’s plugs are connected firmly and correctly.
(3) Check whether the camera’s video format matches.
Avoid exposing the machine to strong
sunlight for a long time. The normal
4
operating temperature of the machine
The machine
is -4°F to 149°F (-20°C to 65°C). After
has overheated working in a high temperature
environment for a period of time, it is
recommended to turn off the power to
let the device rest.
(1) It takes longer time for the first-time
connection
(2) It works with only iPhone’s Carplay
(3)Make sure your iPhone’s Bluetooth and
Wi-Fi work normally and set them to be on.
5
(4)Go to Settings – General Clear
CarPlay can’t be
connections, delete all connection records. Ignore all devices listed on your iPhone’s
connected
Bluetooth list.
(5)Restart the device and your iPhone,
connect them again.
29
(1) Only Android phones are supported
(2)Update your Android phone and the
related APP to the latest version.
6
(3)Do not enable VPN on your mobile
Android Auto can’t be connected
phone (4) Make sure the Wi-Fi and Bluetooth of
your cell phone work well, and set them to be on
(5) Ignore all devices on your Phone’s
Bluetooth list. Restart your Android
phone and the screen.
7 Bluetooth music Set the Audio Output mode to [BT
doesn’t work
Audio]. Other mode doesn’t support Bluetooth music.
Reminder: Please ensure that there are no obstacles and disruptors between the mobile phone and the device, and the Wi-Fi / Bluetooth signal communication is smooth, otherwise the product functions can’t perform properly.
30
Product parameters
Model No.
CS_1026J
Main Control IC Wireless function
High performance SOC Wireless Apple Carplay, Wireless Android Auto
Screen
10.26-inch IPS screen, 1600*600 HD resolution
Storage Wireless module
TF SD Card, Class-10, Compatible with 32GB to 256GB Wi-Fi,Bluetooth, FM Transmitter
Camera
Front 4K Dash Cam and Rear 1080P backup camera
Speaker
2W speaker
FM transmitter
87MHz-108MHz
Reversing video Automatically switch to reversing camera with trigger wire
Working voltage 12V-24V
Power consumption
Size
Less than 10W 260 *130* 66mm
Weight
About 1.1kg
Material
ABS/ PC
31
Documents / Resources
 |
funomo CS_1026J In Car Smart Carplay Screen Multimedia Player [pdf] User Manual CS_1026J In Car Smart Carplay Screen Multimedia Player, CS_1026J, In Car Smart Carplay Screen Multimedia Player, Smart Carplay Screen Multimedia Player, Screen Multimedia Player, Multimedia Player, Player |