FS COM TA1910-4GVC-W Wireless Access Point
Introduction
Thank you for choosing TA 1910-4GVC-W integrated broadband access device. This guide is designed to familiarize you with the layout of the device and describes how to deploy the device in your network.
- TA 1910-4GVC-W
Accessories
- Power Adapter x1
NOTE: This power cord is an exclusive product for AC adapters. Do not use this power cord with other devices. Also, do not use this power cord with other AC adapters.
Hardware Overview
Front Panel Ports
| Ports | Descriptions |
| USB | A USB management port for software, configuration backup and off ine software upgrade |
| TEL | Connect the telephone |
| LAN | Connect the computer or network television |
| PON | Realize the access of GPON ONU |
| RF | Radio-frequency signal transmission |
Top Panel LEDs
| LEDs | State | Description |
| Power | Green | On: The system is powered on normally.
Off: The system is not powered on. |
| PON state | Green | Off: The ONU is not activated.
On: The ONU has been activated. Flicker: The ONU is being activated. |
| Optical signal | Red | Off: The optical power is received normally. Flicker: The received optical power is lower than the threshold of the optical receiver. |
| 2.4G WIFI state | Green | Off: The system is not powered on or the WIFI port is not connected to a network device. On: The WIFI port is connected, but there is no data transmission. Flicker: There is data transmission. |
| 5G WIFI state | Green | Off: The system is not powered on or the WIFI port is not connected to a network device. On: The WIFI port is connected, but there is no data transmission.Flicker: There is data transmission. |
| Ethernet port state | Green | Off: The system is not powered on or the Ethernet port does not connect to the terminal. On: The Ethernet port has been connected, but there is no data transmission.Flicker: There is data transmission through the port. |
| Voice port state | Green | Off: The system is not powered on or the voice port is not registered. On: The voice port is registered successfully, but there is no data transmission. Flicker: There is data transmission on the voice port. |
| WPS state | Green | Off: The system is not powered on or the WPS is not enabled. Flicker: The WPS connection is ongoing. On: The WPS connection is successful. |
| Loop state | Red | Off: The system is not powered on or there is no loop on the port. On: The LAN port has a loop. |
| Optical signal receiving | Red | On: The input optical power is lower than -1 SdBm. Flicker: The input optical power is higher than 3dBm. Off: The device is not powered on. |
| Optical signal receiving | Green | On: The input optical power is between -1 SdBm and 3dBm. |
Installation Requirements
- Make sure the device is put on a horizontal and flat surface.
- To avoid a thunder strike, disconnect all power cords from the power supply and all cables on thunder and rainy days.
- Make sure that the installation site is well-ventilated, the heat of electrical devices is well-discharged and sufficient air circulation is provided for device cooling.
- Use the rated power adapter equipped with the device.
Installation
Desk Mounting
- Connect the PON port to an optical splitter with a single-mode SC optical fiber cable.
- Then connect the splitter to an OLT with a fiber cable.
Connecting the RF Port
Connecting the RF port to a cable television with a network cable.
Configuring the GPON
Computer Setting
Step 1: Click “Start-Cont rol Panel-Network and Internet-Network and Sharing Center-Local Area Connection”, select “Local Area Connection”, and click “Properties”
Step 2: Double click “Internet Protocol 4 (TCP/IPV4)” as shown in the following figure:
Step 3: On the page of Internet Protocol 4 (TCP/IPV4) Properties, select” Obtain an IP address automatically” and “Obtain DNS server address automatically”, and then click “OK”.
Wizard Setting
Step 2: Enter 192.168.123.1 in the address bar and click “Enter” to the web interface. Then enter the UserName (user by default) and Password (123456 by default) respectively in the interface User login.
Step 1: Select “Network” and “Properties”
Troubleshooting
Wifi Has a Signal on the PC but it Cannot Connect to the Internet.
- Check whether the WiFi name is the same as the 5510 of the wireless router;
- Check the strength of the wireless signal. Adjust the location of the wireless router, if the wireless signal is weak.
- Refresh the network list and re-connect to the WiFi;
- Consult the manufacturer of the notebook or wireless adapter card and re-connect according to the relevant guidelines;
- Restart the PC.
Wifi Has No signal on the PC
- Check whether the wireless adapter card is enabled;
- Check whether the driver of the wireless adapter card is successfully installed. If not, please reinstall;
- Check whether the WiFi function of the wireless router is enabled and access to SSID broadcast;
- Check whether the WiFi service is enabled. Right-click “My computer” on the desk of the home a screen (take Windows 7 as an example) and select “Management”. Then select “service and application program”, and select “service” after the page is unfolded. Find “WLAN AutoConfig” and ensure it is enabled;
- Check whether there is a wireless signal if keeping the PC closer to the wireless router.
- Retry to connect another wireless adapter card if the above solutions are unsatisfactory. If not, reset the wireless router.
Online Resources
- Download https://www.fs.com/products_support.html
- Help Center https://www.fs.com/service/fs_support.html
- Contact Us https://www.fs.com/contact_us.html
Product Warranty
Warranty: The GPON ONU enjoys a 1-year limited warranty against defects in materials or workmanship. For more details about the warranty, please check at: https://www.fs.com/policies/warranty.html
Return: If you want to return the item(s), information on how to return can be found at: https://www.fs.com/policies/day_return_policy.html
Documents / Resources
 |
FS COM TA1910-4GVC-W Wireless Access Point [pdf] Owner's Manual TA1910-4GVC-W, 2A2PW143750, TA1910-4GVC-W Wireless Access Point, Wireless Access Point, Access Point, Point |