Fronius Smart Meter IP User Guide

The Fronius Smart Meter IP is a radio equipment type device that is compliant with Directive 2014/53/EU. It is manufactured by Fronius International GmbH. The product allows for communication through WLAN and LAN, and operates at a frequency band of 2.4 GHz. It has an IP20/IP30 rating for housing and connections and has a footprint of 3 TE (3 Modules DIN 43880). The Smart Meter has LEDs to indicate connection status and a boot process. It is compatible with Fronius GEN24, Tauro, Datamanager 2.0 (SnapInverter), and Symo Hybrid.

Technical Data

Permitted ambient temperature: 100 – 240 V
Nominal frequency: 208 – 480 V

Voltage phase/neutral: max. 5 W
Voltage phase/phase: 5 kA

Self-consumption: IP20/IP30
Primary current: 3 TE (3 Modules DIN 43880)

Product Usage Instructions

Mounting: Install the Fronius Smart Meter IP in the desired location.
Power wiring: Connect the appropriate voltage phase/neutral and voltage phase/phase to the Smart Meter.

Data wiring:
- For LAN (GEN24 & Tauro), connect the LAN cable to the Smart Meter.
- For WLAN (GEN24 & Tauro), connect to the access point using the provided SSID and password.
- For Modbus RTU (SnapInverter, GEN24 & Tauro), connect the Modbus RTU cable to the Smart Meter.

Load/Source: Depending on your setup, connect the load/source wires to the appropriate terminals on the Smart Meter.
CT (Current Transformer) Wiring:
- For 1 Phase, 2 Wires – CT: Connect CT1 to the appropriate terminals on the Smart Meter.
- For 3 Phases, 4 Wires – CT: Connect CT1, CT2, and CT3 to the appropriate terminals on the Smart Meter.
- For 2 Phases, 3 Wires – CT: Connect CT1 and CT2 to the appropriate terminals on the Smart Meter.
Modbus RTU BIAS: Set the Modbus RTU BIAS to ON or OFF depending on your requirements.

Battery: Set the Battery switch to ON or OFF depending on your setup.
Modbus RTU Terminating Resistor: Set the Modbus RTU Terminating Resistor to ON or OFF depending on your requirements.

Outside Setup:
- Using a mobile phone, scan the QR-Code on the Smart Meter.
- Follow the instructions provided.
- The initial password for UI is 123.

Inside Setup:
- On a PC, connect to the access point using the provided SN and PW.
- The SSID is FroniusMeter_xxxxx (xxx = Seriennummer) and the password can be found on the Smart Meter.

Fronius International GmbH declares that the radio equipment type Fronius Smart Meter IP is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.fronius.com.

Technical Data

Technical Data
Permitted ambient temperature	from -25° to +55°C
Nominal frequency	50- 60 Hz
Voltage phase / neutral	100 – 240 V
Voltage phase / phase	208 – 480 V
Self-consumption	max. 5 W
Primary current	5 kA
IP range	IP20 / IP30 (Housing / Connections)
Footprint	3 TE (3 Modules DIN 43880)

Communication

Communication
WLAN / LAN	Modbus TCP
WLAN frequency band	2,4 GHz
RS 485	Modbus RTU
Terminating resistor for RS 485	Configurable 0-1
BIAS Network for RS 485	Configurable 0-1
Multimetering	Yes – up to 2 Smart meters (RTU) Modbusinterface
Addressing (Modbus RTU)	In UI
Update possibility	Yes
CTs can be sourced by Fronius	100 A, 250 A, 400 A