1. Introduction
Thank you for choosing the QEP 36" Slimline Manual Tile Cutter. This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your new tile cutter. Please read this manual thoroughly before use and retain it for future reference.
The QEP Slimline Series Tile Cutter is engineered for professional use, designed to cut most ceramic and porcelain tiles up to 36 inches in length. Its unique ultra-slim design, measuring only 5-1/2 inches wide, makes it lightweight and easy to transport. Key features include heavy rubber pads for cutting stability, dual chrome-plated rail bars, and linear ball bearing slides for exceptionally smooth scoring. The cutter is equipped with a durable 7/8 inch titanium-coated tungsten-carbide ball bearing cutting wheel, ensuring long-lasting performance even with hard porcelain tiles. For larger format tiles, the base includes four convenient side arm extensions.
Figure 1.1: QEP 36" Slimline Manual Tile Cutter, showcasing son design compact et robuste.
2. Consignes de sécurité
Always follow basic safety precautions when using this product to reduce the risk of injury. Read all instructions before operating the tile cutter.
- Portez une protection pour les yeux : Always wear ANSI-approved safety goggles or safety glasses with side shields when operating the tile cutter.
- Porter des gants : Protect your hands from sharp tile edges and potential cuts.
- Surface de travail stable : Ensure the tile cutter is placed on a stable, level, and non-slip surface before use.
- Gardez la zone de travail propre : Clear the work area of debris and obstructions to prevent accidents.
- Manipulation appropriée : Manipulez les carreaux avec précaution, car les bords peuvent être coupants après la découpe.
- Tenir les enfants à l’écart : Do not allow children or untrained persons to operate the tile cutter.
- Inspecter avant utilisation : Before each use, inspect the cutter for any damaged or loose parts. Do not use if damaged.
- Utiliser correctement : Use the tool only for its intended purpose of cutting ceramic and porcelain tiles.
3. Installation
3.1 Déballage et inspection
Carefully remove the tile cutter from its packaging. Inspect all components for any signs of damage during shipping. Ensure all parts listed in the 'Included Components' section (see Specifications) are present.
3.2 Préparation de la zone de travail
Place the tile cutter on a flat, stable, and clean surface. The heavy rubber pads on the base provide cutting stability, but a firm foundation is crucial for accurate cuts.
3.3 Extending Side Arm Supports
For cutting large format tiles, extend the four side arm extensions located on the base of the cutter. These arms provide additional support to prevent the tile from tipping during the scoring and breaking process.
Figure 3.1: Key features of the QEP Slimline Tile Cutter, highlighting the tile support arms.
4. Mode d'emploi
4.1 Préparation du carrelage
Measure and mark the desired cut line on your ceramic or porcelain tile. Ensure the tile is clean and free of debris.
4.2 Positioning the Tile
Place the tile on the cutter's base, aligning the marked cut line with the scoring wheel. Utilize the metal rip guide to help measure and hold the tile securely in place, ensuring accuracy during the cut. For diagonal cuts, align the corner of the tile with the scoring wheel.
Figure 4.1: Demonstrating the tile cutting process, suitable for ceramic and porcelain tiles up to 1/2 inch thick.
4.3 Notation de la tuile
Lower the handle so the scoring wheel makes contact with the tile. Apply firm, consistent pressure and push the handle forward along the dual chrome-plated rail bars. The linear ball bearing slides ensure a smooth and precise score line across the entire tile surface. A single, continuous score is generally recommended for best results.
Figure 4.2: Close-up of the scoring wheel, which is a replaceable tungsten-carbide 7/8 inch wheel.
4.4 Casser la tuile
Once the tile is scored, position the breaking bar directly over the scored line. Apply quick, downward pressure on the handle to snap the tile along the score. The reinforced thick steel base and tile support arms provide stability during this process.
Figure 4.3: Breaking the tile after scoring.
4.5 Cutting Capacities
- Rip Cut: Up to 36 inch tile.
- Diagonal Cut: Up to 25 inch tile.
- Tile Depth: Up to 1/2 inch (13 mm) maximum.
Figure 4.4: QEP 36" Slimline Tile Cutter dimensions and cutting capabilities.
5. Entretien
5.1 Nettoyage
After each use, wipe down the tile cutter with a damp cloth to remove tile dust and debris. Ensure the rail bars are clean to maintain smooth operation. Do not use harsh chemicals or abrasive cleaners.
5.2 Scoring Wheel Replacement
The 7/8 inch tungsten-carbide scoring wheel is replaceable. If you notice a decrease in cutting performance or chipping of tiles, it may be time to replace the wheel. The cutter is compatible with the QEP 21178 Scoring Wheel (sold separately). Refer to the QEP website or product packaging for specific replacement instructions.
5.3 Stockage
Store the tile cutter in a dry, clean environment, away from extreme temperatures and moisture. Its narrow 5-1/2 inch width makes it less bulky and easy to store.
6. Dépannage
| Problème | Cause possible | Solution |
|---|---|---|
| Carrelage non net / Écaillage | Dull scoring wheel; Insufficient pressure; Incorrect scoring technique; Tile type not suitable. | Replace scoring wheel; Apply firm, consistent pressure; Ensure single, continuous score; Verify tile is ceramic or porcelain. |
| Tile not breaking cleanly / Uneven break | Inconsistent score line; Breaking bar not aligned; Insufficient breaking pressure. | Ensure a straight, consistent score; Align breaking bar precisely over score line; Apply quick, decisive downward pressure. |
| Cutter carriage not sliding smoothly | Dust/debris on rail bars; Damaged rail bars or bearings. | Clean rail bars thoroughly; Inspect for damage, contact support if damaged. |
7. Spécifications
- Fabricant: QEP
- Numéro de pièce : 10636Q
- Numéro de modèle de l'article : 10636Q
- Poids de l'article : 18 livres
- Dimensions du produit : 45 x 5.5 x 7 pouces
- Source d'alimentation : Alimenté à la main
- Quantité de l'emballage : 1
- Composants inclus : 1 Coupe-carreaux
- Piles requises ? : Non
- Molette de coupe : Replaceable Tungsten-carbide 7/8 inch scoring wheel
- Max. Rip Cut: 36 pouces
- Max. Diagonal Cut: 25 pouces
- Max. Tile Thickness: 1/2 pouce (13 mm)
8. Garantie et assistance
For information regarding warranty coverage, product support, or to purchase replacement parts, please visit the official QEP website or contact QEP customer service directly. Contact details can typically be found on the QEP website ou sur l'emballage du produit.
Please have your model number (10636Q) and purchase date available when contacting support.
