REV.: 20211109
Guide # 102871
STAND ALONE INSTALLATION
ADDENDUM – SUGGESTED WIRING CONFIGURATIONVEHICLE
YEARS

2013 Standard Key Remote Starters and Alarm Systems

ONLY COMPATIBLE WITH AUTOMATIC TRANSMISSION VEHICLES.
Vehicle functions supported in this diagram (functional if equipped)

• Immobilizer bypass
• T-Harness available (sold separately)
• Lock
• Unlock
• Arm
• Disarm
• Parking Lights
• Tachometer
• Heated Seats
• Door Status
• Trunk Status
• Hood Status
• Hand-Brake Status
• Foot-Brake Status
• PK3, Passlock
• OEM Remote monitoring

CADILLAC

Escalade: 2007-2014

FIRMWARE VERSION

To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.

Program bypass option:	UNIT OPTION	DESCRIPTION
	C1	OEM Remote status (Lock/Unlock) monitoring

IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:

A11

Hood trigger (Output Status).

MANDATORY INSTALL

* HOOD PIN CONTACT

HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.

A11

Notice: the installation of safety elements are mandatory. The hood pin is an essential security element and must be installed.

THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

PARTS REQUIRED (NOT INCLUDED)

1x FLASH LINK UPDATER, SOFTWARE Microsoft Windows Computer with Internet connection

FLASH LINK MOBILE 1x FLASH LINK MOBILE APP Smartphone Android or iOS with Internet connection (provider charges may apply).

MANDATORY

HOOD PIN CONTACT

REMOTE START SAFETY OVERRIDE SWITCHVALET SWITCH

Part #: RSPB available, Sold separately.
Notice: the installation of safety elements are mandatory.
The hood pin and the valet switch are essential security elements and must be installed.

STAND ALONE CONFIGURATION

	Program bypass option OEM Remote Stand Alone Remote Starter:	UNIT OPTION	DESCRIPTION
		D1.10 D1.1	By default, LOCK, LOCK, LOCK LOCK, UNLOCK, LOCK
	Program bypass option wither remote:	UNIT OPTION	DESCRIPTION
		C1	OEM Remote Monitoring
	Program bypass option with RF KIT antenna:	UNIT OPTION	DESCRIPTION
		H1 to H6	Supported RF Kits and select RF Kit

REMOTE STARTER FUNCTIONALITY

All doors must be closed.	Press the OEM remote’s Lock button 3x to remote-start (or remote-stop) the vehicle.	The vehicle will START.

REMOTE STARTER DIAGNOSTICS
MODULE RED LED

x2 flash :	Brake ON
x3 flash :	No tach
x4 flash :	Ignition before start
x5 flash :	Hood Open

REMOTE STARTER WARNING CARD

CUT THIS WARNING CARD AND STICK IT ON A VISIBLE PLACE: or use the package RSPB, Sold separately.

WARNING
REMOTE STARTER
THE VEHICLE CAN BE STARTED BY EITHER: PRESSING THE LOCK BUTTON ON THE OEM REMOTE 3 TIMES CONSECUTIVELY OR BY A SMARTPHONE. TURN ON THE SAFETY SWITCH LOCATED UNDER THE DASHBOARD BEFORE WORKING ON
THE VEHICLE.

DESCRIPTION

WIRING CONNECTION

KEY BYPASS PROGRAMMING PROCEDURE 1/2

	Press and hold the programming button: Connect the 4-PIN Data-link harness (Black connector). → The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.
	Release the programming button when the LED is BLUE. If the LED is not solid BLUE disconnect the 4-Pin connector (Data-Link) and go back to step 1.
	Insert the required remaining connectors.
	Turn the key to the Ignition ON/RUN position. → The Blue LED will flash rapidly.
	Press and release the programming button once (1x). → The Blue LED will turn OFF. → The YELLOW and RED LEDS will alternate..
	Turn the key to the OFF position.
	Disconnect all the connectors and after the Data-Link (4-pins) connector.
	Microsoft Windows Computer with Internet connection*
	Smartphone* (Internet provider charges may apply) Use the tool: FLASH LINK UPDATER or FLASH LINK MOBILE to visit the Cryptor menu. *Parts required (not included)
	AFTER DCRYPTOR PROGRAMMING COMPLETED Go back to the vehicle and reconnect the 4-Pin (Data-Link) connector and after, all the remaining connector.
	The module is now programmed.
	REMOTE STARTER / ALARM VERIFICATION Test the remote starter. Remote start the vehicle.

OPTIONAL RF-KIT PROGRAMMING

PROGRAM BYPASS OPTION 

Program bypass option:

H2

☑Supported RF-KITS enable ☑ H2 Fortin 2

OPTIONAL FORTIN RF KIT SERIES 4 OR SERIES 9 PROGRAMMING

				4X BRAKES	ON EACH TRANSMITTER
The module must be programmed on the vehicle.	Turn the key to the ON/RUN position.	Turn the ignition to the OFF position.	Turn the key to the ON/RUN position.	Press and release the brake pedal four times. The LED will turn off each time.	4 BUTTONS PRESS AND RELEASE APPUYEZ ET PRESS AND RELEASE 1 BUTTON PRESS APPROX. 12 SEC. AND WAIT FOR THE BLUE LED TO TURN OFF THEN BACK ON SOLID THEN RELEASE.	Turn the ignition to the OFF position.
			The LED will turn ON solidi.	The LED will flash rapidly.	The LED will flash rapidly.	The LED will turn Off.
MAKE SURE THE IGNITION KEY HAS BEEN IN THE OFF POSITION FOR AT LEAST 5 SECONDS.	The YELLOW LED will turn ON solid.	The YELLOW LED will turn Off.	The YELLOW LED will turn ON solid.	The 3 LED will turn ON solid.	The 3 LED will turn off each time.	The 3 LED will turn off.

REMOTE STARTER FUNCTIONALITY

Notice: Updated Firmware and Installation Guides
Updated firewire and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest firmware and download the latest installation guide(s) prior to the installation of this product.
WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever.
It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualified technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

This guide may change without notice. See www.fortin.ca for latest version.
TECH SUPPORT
Tél: 514-255-HELP (4357) 1-877-336-7797

Made in Canada
ADDENDUM GUIDE
www.fortinbypass.com
WEB UPDATE

Documents / Resources

	FORTIN 2013 Standard Key Remote Starters and Alarm Systems [pdf] Installation Guide 102871, 2013, 2013 Standard Key Remote Starters and Alarm Systems, Standard Key Remote Starters and Alarm Systems, Key Remote Starters and Alarm Systems, Remote Starters and Alarm Systems, Starters and Alarm Systems, Alarm Systems, Systems
	FORTIN 2013 Standard Key Remote Starters and Alarm Systems [pdf] Installation Guide 102861, 2013, 2013 Standard Key Remote Starters and Alarm Systems, Standard Key Remote Starters and Alarm Systems, Key Remote Starters and Alarm Systems, Remote Starters and Alarm Systems, Starters and Alarm Systems, Alarm Systems, Systems

References

• User Manual