FOR-X X-510DSP Digital Media Receiver
WARNINGS & PRECAUTIONS:
To avoid risk of serious injury or possible violation of laws, please read the following thoroughly before installation or connecting.
- This product is designed specifically for use with 12-volt, negative ground electrical systems only.
- Having the wiring and installation done by an expert. Be sure to disconnect the cable from the negative battery terminal while installtion.
- This apparatus shall not be exposed to dripping or splashing, and no object filled with liquids shall be placed on the apparatus.
- Fuses shall be replaced only with the correct type and fuse value, and only when the apparatus is powered off.
- To prevent a short circuit, never put or leave any metallic objects(such as coins or metallic tools)inside the unit.
- Never set the volume of this product so high that you cannot hear outside traffic and emergency vehicles.
PRODUCT FEATURES
- LCD: VA-LCD
- DSP: Built-in
- Key Light: Multi-Color
- Bluetooth: Version 5.1
- Remote: Support
- Pre-Output: 6CH x 4V
- Time Alignment: Support
- AUX In: Support
- SD Card: Support
- Bluetooth Music: Support
- EQ: 28 band/9 Preset
- Radio: FM/ AM/RDS
- USB: Charge 2A
- APP Control: iOS and Android Phone
- Max Power: 4 x 60W
- Subwoofer Control: Support
- Dual Bluetooth Connection: Support
- SWIControl: Support
- Audio Format: MP3/WMA/AAC/FLAC
- External Microphone: Support
INSTALLATION
Installation Procedures
- First complete the electrical connections and then check for correctness.
Installation Opening
- This unit can be installed in any dashboard Having an opening as shown below:
To Install The Car Radio
Be sure you test all connections first, and then follow these steps to install this unit.
- Make sure the ignition is turned off, and then disconnect the cable from the vehicle battery’ s negative (-) terminal.
- Disconnect the wire harness and the antenna.
- Remove the detachable panel and decorative enclosure frame and place on one side.
- Insert the two brackets into the left and right sides of the chassis, as shown in the following figure, and separate the chassis from the sleeve.
- Insert the installation sleeve into the center console to be installed, and bend the clip using a screwdriver. Make sure the locking rod is flush with the mounting sleeve and does not protrude.
- Connect cables as shown in the Wiring diagram.
- Insert the car radio into the mounting sleeve.
- Install decorative enclosure frame.
ACCESSORY LIST
DIMENSION
DIMENSION(UNIT:MM)
WIRING DIAGRAM
REMOTE OPERATION
BLUETOOTH OPERATION
Bluetooth Pairing
The first time pair a mobile phone with a receiver, please follow the below steps
- When there is no pairing, in any mode, the BT on the LCD will flash, and the pairing can be performed at this time.
- Turn on the phone’s Bluetooth to Search X-SlODSP.
- Click on the X-SlODSP on the phone to connect. After the connection is successful, the BT will stop flashing.
- When pairing is complete, the mobile phone audio will automatically transfer to the car audio system whenever a call is made or received, or when the mobile phone plays music.
Note:
For more details of bluetooth pairing, please refer to the owner’s manual for your mobile phone.
RADIO OPERATION: Start Listening
| To | Operation (panel) | Remark |
| Auto memory | Press and hold  |
18 FM/12 AM |
| Band selection | Press /BND |
FM1/FM2/FM3/AM1/AM2 |
| Seek a station manually | Press  |
|
| Search the next or previous frequency step by step | Press and hold |
|
| Store a station | Press and hold 1-6 |
| RADIO | |
|
FM Frequency Range |
Europe Area: 87.5 ~ 108.0 KHz (50KHz / Step) |
| U.S.A.Area: 87.5~107.9 KHz (200 KHz/ Step) | |
| ASIA Area: 87.5~108.0 KHz (100 KHz/ Step) | |
| RUSS Area: 65.0 ~74.0 KHz (30 KHz/ Step) | |
| Preset | 18FM / 12 AM |
USB&SD PLAYBACK
| To | Operation (panel) |
| Track selection Fast playback | Press
Press and hold |
| Playback/Pause | Press  |
| Track pre-play | Press  |
| Repeat playback | Press 
• REPEAT ONE. REPEAT DIR. REPEAT ALL |
|
Random playback |
Press 
• ON/OFF |
| Folder selection | Press  |
AUX INPUT
- Connect a portable audio player(commercially available). Auxiliary input jack
Auxiliary input jack 3.5mm stereo mini plug with “L” shaped connector. (commercially available). - Press[
]buttons to select AUX IN. - Turn on the portable audio player and start playback.
EXTERNAL MICROPHONE
Note:
Microphone(Optional)Since the panel microphone is far from the driver’s position, when using an external microphone, you can get better voice calls
AUDIO SETTINGS
- Press the knob to enter the [MENU].
- Turn the knob to select [AUDIO], then press the knob.
Audio Settings List
| Menu | Adjustment |
| SW LEVEL | SVOL -8 ~ +8 |
| PRESET EQ | USER/NATURAL/POP/CLASSIC/ROCK/JAZZ/FLAT/ COUNTRY/OPTIMAL
L 30HZ/60HZ/80HZ/120HZ/160HZ/250HZ/400HZ/600HZ/ |
|
1.5KHZ/2KHZ/2. 5KHZ/3KHZ/3. 5K/4K/5K/6K/7K/8K/9K/l1K/ 12K/13K/14K/15K/16K/17K/18K/19K |
|
| LOUD | OFF/ON |
| BASS | BASS -7 ~ +7 |
| MIDDLE | MIDDLE -7 ~ 7 |
| TONE | TONE -7 ~ 7 |
| TREBLE | TREBLE -7 ~ +7 |
| BALAN | BALAN L7-L0, 0, Rl-R7 |
| FADER | FADER R7-Rl, 0, Fl-F7 |
| AUDIO RESET | NO/YES |
Subwoofer Volume Adjustment
- 1. Turn the knob to select [SW LEVEL], then press the knob.
- 2. Turn the knob to adjust SVOL [ -8 to +8].
Preset EQ Select
- 1. Turn the knob to select [PRESET EQ ], then press the knob.
- 2. Turn the knob to select [USER/NATURAL/POP/CLASSIC/ROCK/
- JAZZ/FLAT/COUNTRY /OPTIMAL].
User EQ Setup
- 1. Turn the knob to select [PRESET EQ ], then press the knob.
- 2. Turn the knob to select [USER], then press the knob.
- 3. Turn the knob to select frequency for adjustment.
Loundness Setup
- 1. Turn the knob to select [SOUND], then press the knob.
- 2. Turn the knob to select [OFF/ON].
Bass Adjustment
- 1. Turn the knob to select [BASS], then press the knob.
- 2. Turn the knob to adjustment [-7 to +7].
AUDIO SETTINGS
Middle Adjustment
- Turn the knob to select [MIDDLE] then press the knob.
- Turn the knob to select [ -7 to + 7 ] .
Tone Adjustment
- Turn the knob to select [TONE], then press the knob.
- Turn the knob to select [ -7 to + 7 ] .
Treble Adjustment
- Turn the knob to select [ TREBLE ], then press the knob.
- Turn the knob to select [ -7 to + 7 ] .
Balance Adjustment
- Turn the knob to select [BALAN], then press the knob.
- Turn the knob to select [ L7-L0 to Rl-R7 ].
Fader Adjustment
- Turn the knob to select [ FADER ], then press the knob.
- Turn the knob to select [ R7-R0 to Fl-F7 ].
Audio Setup Reset
- Turn the knob to select [ AUDIO RESET ], then press the knob.
- Turn the knob to select [ NO/YES ].
CLOCK AND DATE SETTINGS
- Press the knob to enter the [MENU].
- Turn the knob to select [CLOCK], then press the knob.
Clock And Date Settings List
| Menu | Adjustment |
| CLOCK FORMAT | 12H/24H |
| CLOCK ADJUST | 00:00 |
| DATE FORMAT | DD-MM-YY/MM-DD-YY |
| DATE SET | 01/01/2023 |
Clock Format Settings
- 1. Turn the knob to select [CLK FRMT], then press the knob.
- 2. Turn the knob to select [12H/24H].
Clock Adjust
- 1. Turn the knob to select [CLK ADJ], then press the knob.
- 2. Turn the knob to adjust.
- 3. Press the knob to switch the clock/minute adjustment.
Date Format Settings
- 1. Turn the knob to select [DATE FORMAT], then press the knob.
- 2. Turn the knob to select [DD-MM-YY/MM-DD-YY].
Date Settings
- 1. Turn the knob to select [DATE SET], then press the knob.
- 2. Turn the knob to adjust.
- 3. Press the knob to switch day/month/year adjustment
XOVER SETUP
- Press the knob to enter the [MENU].
- Turn the knob to select [X/OVER], then press the knob.
- Turn the knob to select [SUB SET], then press the knob.
Subwoofer Xover List
| Menu | Adjustment | |
| F+R SET | HPF FREQ | OFF/30HZ/40HZ/S0HZ/63HZ//80HZ/100HZ/
/125HZ/160HZ/200HZ/250HZ/ |
| LPF FREQ | OFF/1KHZ/l.6KHZ/2.5KHZ/3. l 5KHZ/4K/ SKHZ/6. 3KHZ/8KHZ110KHZ/12.SKHZ | |
| SUBSET | FRQ THROUGH | 32HZ/40HZ/S0HZ/63HZ/80HZ/100HZ/
125HZ/160HZ/200HZ/250HZ |
| SW PHASE | NORMAL/REVERSE | |
| SW GAIN | GAIN -8 ~ 8 | |
Front&Rear HPF Frequency Setup
- 1. Turn the knob to select [HPF FREQ], then press the knob.
- 2. Turn the knob to select frequency [OFF/30HZ/40HZ/S0HZ/63HZ/70HZ/ 80HZ/90HZ/100HZ/125HZ/160HZ/180HZ/220HZ/250HZ/315HZ/400HZ/500HZ/630HZ/700HZ/800HZ].
Front&Rear LPF Frequency Setup
- 1. Turn the knob to select [LPF FREQ], then press the knob.
- 2. Turn the knob to select frequency [FULL/1K/1.6K/2.SK/3.15K/4K/SK/ 6.3K/8K/10K/12.5K].
Subwoofer Frequency Through Setup
- 1. Turn the knob to select [SW FRQ THROUGH ], then press the knob.
- 2. Turn the knob to select frequency[32Hz/40Hz/50Hz/63Hz/80Hz/100Hz/ 125Hz/160HZ/200H/250HZ].
Subwoofer Phase Setup
- 1. Turn the knob to select [SW PHASE], then press the knob.
- 2. Turn the knob to select [NORMAL/REVERSE].
Subwoofer Gain Setup
- 1. Turn the knob to select [SW GAIN], then press the knob.
- 2. Turn the knob to select [0-5].
DTA SETTINGS
- Press the knob to enter the [MENU].
- Turn the knob to select [DTA SET], then press the knob.
DTA Settings List
| Menu | Adjustment | |
| CAR TYPE | SMALL CAR/MEDIUM CAR/LARGE CAR | |
| POSITION | USER/FRONT R/FRONT L/CENTER | |
| DELAY UNIT | MS/CM/INCH | |
| DISTANCE | FRONT LEFT | FL 0CM – 680CM |
| FRONT RIGHT | FR 0CM – 680CM | |
| REAR LEFT | RL 0CM – 680CM | |
| REAR RIGHT | RR 0CM – 680CM | |
| DTA RST | NO/YES | |
Car Type Settings
- 1. Turn the knob to select [CAR TYPE], then press the knob.
- 2. Turn the knob to select [SMALL /MEDIUM /LARGE].
Listening Position Settings
- 1. Turn the knob to select [POSITION], then press the knob.
- 2. Turn the knob to select [USER/FRONT R/FRONT L/CENTER].
Delay Unit Settings
- 1. Turn the knob to select [UNIT], then press the knob.
- 2. Turn the knob to select [CM/MS/INCH].
DSP Reset
- 1. Turn the knob to select [DTA RST], then press the knob.
- 2. Turn the knob to select [NO/YES].
ANIMATION SETTINGS:
- 1. Press the knob to enter the [MENU].
- 2. Turn the knob to select [ANIMATION], then press the knob.
- 3. Turn the knob to select [OFF/PER 15SEC/30SEC/1MIN/2MIN/4MIN].
| Menu | Adjustment |
| ANIMATION | OFF/PER 15SEC/30SEC/1MIN/2MIN/4MIN |
TIME ALIGNMENT(DISTANCE)
- Press the knob to enter the [MENU].
- Turn the knob to select [DTA SET], then press the knob.
- Turn the knob to select [DISTANCE], then press the knob.
- Turn the knob to select[F LEFT/F RIGHT/R LEFT/R RIGHT/SUBWOOFER] to adjust.
Determining the value for<Position> adjustment.
- Determine the center of the currently set listening position as the reference point.
- The adjustable speaker has five directions: front left, front right, back left, back right, and back.
- The time for the speakers in the five directions to reach the center is the same by default.
- Set the value for each speaker, the delay range: 0-20ms.
- Adjust the increase or decrease of each speaker, 0.2ms each time
Example:When <back> is selected as the listening position
TUNER SETTINGS
- Press the knob to enter the [MENU].
- Turn the knob to select [TUNER], then press the knob.
Tunner Settings List
Stereo/Mono Select
- Turn the knob to select [STEREO or MONO], then turn the knob to select [STEREO/MONO].
DX/Local Select
- Turn the knob to select [LOC or DX], then turn the knob to select
- [DX /LOCAL].
- Remark: DX: Distant exchange
Tuner Area Select
- Turn the knob to select [REGIONAL], then turn the knob select
- [ASIA/OIRT /EUR/USA].
RDS ON/OFF
- Turn the knob to select [RDS OFF], then turn the knob select
- [RDS OFF, ON].
DEMO MODE SELECT
- Press the knob to enter the [MENU].
- Turn the knob to select [DEMO MODE], then press the knob.
- Turn the knob to select [OFF/ON].
| Menu | Adjustment |
| DEMO MODE | OFF/ON |
DISPLAY SETTINGS
- Press the knob to enter the [MENU].
- Turn the knob to select [DISPLAY], then press the knob.
Display Settings List
| Menu | Adjustment |
| SPECTRUM | OFF/ON |
| ID3 TAG | OFF/ON |
| MODE SEL | C-MODE 1/C-MODE 2/C-MODE 3 |
| BRIGHT | MANUAL M-LEVER 1~8
AUTO A-LEVER 1~8—->START—->18:00—->STOP—— >07:00 |
| VERSION | VER 1.0 |
Spectrum ON/OFF
- Turn the knob to select [SPECTRUM], then press the knob.
- Turn the knob to select [OFF/ON].
ID3 ON/OFF
- Turn the knob to select [ID3 TAG], then press the knob.
- Turn the knob to select [OFF/ON].
Key Light Select
- Turn the knob to select [MODE SEL], then press the knob.
- Turn the knob to select [C-MODE 1/C-MODE 2/C-MODE 3].
Key Light Bright Setup
- Turn the knob to select [BRIGHT], then press the knob.
- Turn the knob to select [MANUAL], then press the knob.
- Turn the knob to select [M-LEVER 1~8].
- Turn the knob to select [AUTO], then press the knob.
- Turn the knob to select [A-LEVER 1~8], then press the knob.
- Turn the knob to select [START], then press the knob to setting start time.
- Turn the knob to select [STOP], then press the knob to setting stop time.
System Version
- Turn the knob to select [VERSION], then press the button to query the system version information.
TROUBLE SHOOTING
SPEAKER CONNECTION
Do not connect the speaker leads of the power cord to the car battery; otherwise, the unit wil be seriously damaged. Before oconnecting the speaker leads of the power cord to the speakers, check the speaker wiring in your car.
SPECIFICATION
APP OPERATION
APP Download
- Method 1: Please scan the QR code on the cover to download the APP and install it on your Android or Apple device.
- Method 2: Please go to the APPLE APP Store or Google Play Store and search [AUDIO DSP Control] APP, after downloading the APP, install it on your Appale&Android devices.
APP Connection
- 0pen the [AUDIO DSP Control] APP, click[■] to search for X-SlODSP.
- Click X-510DSP to connect, the [
;] will be red after the connect is successful.
Documents / Resources
 |
FOR-X X-510DSP Digital Media Receiver [pdf] Owner's Manual X-510DSP, X-510DSP Digital Media Receiver, Digital Media Receiver, Media Receiver, Receiver |
