FOAMit MBS-C Boot Scrubber with Combo Handle

Specifications

• Model: MBS | MBS-C
• Product Components: Straight handle, Debris shield, Bootscrubber base, Combo handle, Side brush, Sole brush, Debris tray

Product Information

The Manual Boot Scrubber (MBS | MBS-C) is designed for sanitizing footwear at transition zones. It is intended for use with fully protective footwear only. The unit includes components such as a straight handle, debris shield, boot scrubber base, side brush, sole brush, and debris tray.

Usage Instruction

Installation Instructions

1. Select a suitable location for the unit.
2. Attach the handle by sliding it into the boot scrubber base and fasten it with bolts on both ends.
3. Tighten the bolts and lock nuts on both sides to secure the handle.
4. Connect the debris shield by sliding hooks into slots on the back of the boot scrubber frame. Note: Remove brushes before installing/uninstalling the debris shield.
5. Slide the debris tray under the boot scrubber base and lift it to hook into the front slots of the boot scrubber frame for secure placement.
6. If desired, the unit can be securely installed on the floor (mounting hardware not included).

Operating Instructions

1. Grip the handle above the manual boot scrubber with both hands to establish 3 points of contact.
2. Place one foot in the brush and move it back and forth to remove debris. Repeat with the other foot.

Servicing Instructions

For the MBS model with a straight handle, ensure that only authorized parts listed in the manual are used for servicing or modifications to prevent improper operation of the unit.

FAQ

• Q: Can I use the Manual Boot Scrubber with any type of footwear?
• A: No, the unit is designed for use with fully protective footwear only to help sanitize at transition zones.

Safety

WARNING

PEOPLE OR OBJECTS CAN BE HURT OR DAMAGED IF THIS UNIT IS NOT USED CORRECTLY!

• Failure to read all the instructions before operating the unit may result in personal injury or death from the improper use. Anyone handling, operating or using the unit must read and understand the instructions in the manual. The buyer assumes all responsibility for safety and proper use in accordance with the instructions.
• Using or servicing the unit without appropriate personal protective equipment (PPE) may result in serious injury. Always wear PPE as indicated in the Safety Data Sheet (SDS) when using or servicing the unit.
• This unit is for use with fully protective footwear only. This unit is designed to help sanitize footwear at transition zones and is not intended for any other use. Servicing or modifying this unit with parts not listed in this manual may cause the unit to operate improperly. Do not use unauthorized parts when servicing the unit.

PROTECT THE ENVIRONMENT
Please dispose of packaging materials, old machine components, and hazardous fluids in an environmentally safe way according to local waste disposal regulations.

Maintenance

WARNING

Servicing or modifying this unit with parts not listed in this manual may cause the unit to operate improperly. Do not use unauthorized parts when servicing the unit. This unit is for use with fully protective footwear only.

Maintaining Your Unit

To keep your unit operating properly, perform the following daily maintenance procedures:

• Remove brushes by lifting them out from the brush bracket. Remove debris and clean.
• Brushes should be replaced every 6 months depending on wear.
• Slide out the debris tray. Empty debris and wipe clean.
• The base assembly of the unit is fully stainless and can be cleaned in place by method suitable for stainless steel.

Product Components

Get to know the components that you will need to use, adjust or assemble.

1. Straight handle
2. Debris shield
3. Boot scrubber base
4. Combo handle
5. Side brush
6. Sole brush
7. Debris tray

Using Your Unit

Installation Instructions

1. Select the desired location to place the unit.
2. Attach handle (a) by sliding it into the boot scrubber base (b). Fasten with bolts on both ends.
3. Secure the handle by tightening the bolt and lock nut on both sides.
4. Connect debris shield (c) by sliding hooks into slots on the back of the boot scrubber frame
   Note: Brushes must be removed before installing/ uninstalling debris shields.
5. Slide debris tray (d) under the boot scrubber base (b). Lift up and hook the tray into the front slots of the boot scrubber frame to secure.
6. If desired, the unit is designed for secure floor installation. Mounting hardware not included
   Operating Instructions
7. Grip the handle (a) above the manual boot scrubber with both hands to establish 3 points of contact.
8. Place one foot in the brushes and push foot back and forth to remove debris. Repeat the process with your other foot.
   Handling Instructions
9. Use the indicated lift points for proper handling of your unit

Servicing Your Unit

MBS

Manual boot scrubber with straight handle

Optional Component
DBSH-EXT:
Debris shield extension for manual boot scrubber – stainless steel

Scan this code for user manual

Documents / Resources

FOAMit MBS-C Boot Scrubber with Combo Handle [pdf] User Manual MBS, MBS-C, MBS-C Boot Scrubber with Combo Handle, MBS-C, Boot Scrubber with Combo Handle, Scrubber with Combo Handle, Combo Handle, Handle

References

• User Manual