FLSUN S1 Ultra High Speed 3D Printing
Product Specifications:
- Model: OVXQ6
- Power: 9V
- Dimensions: Varies
- Weight: Varies
Product Usage Instructions
Setup
To begin using the product, follow these steps:
- Unpack the product from the box.
- Check all components for any damage.
- Connect the power source as indicated in the manual.
Operation
Once the product is set up, you can operate it by:
- Pressing the power button to turn it on.
- Follow the on-screen instructions for further usage.
Maintenance
To ensure the product’s longevity, remember to:
- Clean the product regularly with a soft, dry cloth.
- Avoid exposing the product to extreme temperatures or moisture.
Frequently Asked Questions
Q: How do I change the settings on the product?
A: To modify settings, navigate to the settings menu using the provided controls and make adjustments as needed.
Q: What should I do if the product stops working suddenly?
A: If the product malfunctions, first check the power source and connections. If the issue persists, contact customer support for assistance.
Q: Can I use the product outdoors?
A: The product is designed for indoor use. Avoid exposing it to outdoor elements to prevent damage.
Instruction Manual
Ultra High-Speed 3D Printing
Zhengzhou Chaokuo Electronic Technology Co., Ltd
Advice And Guidance
- Do not operate the machine according to methods other than those specified in the manual to avoid possible injury or property damage.
- Do not place the printer near flammable, explosive or high heat sources, make sure that the printer is in a cool, dust free and well ventilated area.
- Be careful touching the print bed, print nozzle, or other high temperature areas during or soon after use to avoid severe burns.
- Do you reach inside the print area while the machine is in use to avoid injury from high speed movements.
- Do not allow children or persons who have not read the instructions in detail to operate it alone to avoid personal injury or property damage.
- Routine maintenance should be performed on the printer to ensure a long service life. The printer should be powered off before maintenance is performed, especially important on working parts such as the effector module and guide rails.
- In case of an emergency during printing, press and hold the on/off button for 1.5 seconds to stop the printer, and then turn off the power.
- If the printer is not going to be used for and extended period of time unplug the power cord.
- Each printer is thoroughly tested before leaving the factory to ensure quality and functionality. It is normal to find evidence of prior use.
- Visit the official Flsun Wiki for more tutorials on machine use and maintenance: http://wiki.flsun3d.com/en/home.
Parameter
| PRODUCT | FLSUN S1 | |
| Printing Technology | Fused Deposition Modeling (FDM) | |
| Printing Accuracy | +0.1mm | |
| Recommended Layer Height | 0.1-0.35mm | |
|
Chassis |
Build Volume | o320 * 430mm |
| Frame | Full Metal | |
|
Dimensions |
Product Dimensions | 550*595*1030mm |
| Package Dimensions | 640*680*1120mm | |
| Net Weight | 41kg | |
| Gross Weight | 52kg | |
|
Effector |
Extruder | Dual-Gear Direct Drive Extruder |
| Nozzle | Hardened Steel | |
| Nozzle MAX Temp | 350C | |
| Nozzle Diameter | 0.4mm | |
| Filament Diameter | 1.75mm | |
| Motor | Motor Types | 36V Closed-loop motor |
| Motor Calibration | Support | |
|
Bed |
Build Plate | Textured PEI Print Surface |
| Bed MAX Temp | 120C | |
| Smart Zone Heating | Inner Circle o220mm,Outer Ring220-320mm | |
|
Materials |
Supported | PLA, PETG, TPU, ABS, ASA, PVA, PET, PA, PC, Carbon etc. |
| Drying | Separate Heating elements,Desiccant | |
| Cooling | Fan | CPAP turbofan 40000 rpm |
|
Speed |
MAX Speed | 1200mm/s |
| MAX Acceleration | 40000mm/s2 | |
| MAX Flow Rate | 110mm3/s PLA | |
|
PSU |
Input | 110-240V,50/60HZ |
| Power | 1300W@220V,600W@110V | |
|
Electronics |
Display | Full-Integration Touchscreen |
| Storage | 16GB EMMC,32GB USB Flash | |
| Control interface | Touchscreen, PC Interface | |
| CPU | Quad-Core ARM A7 1.5 GHz | |
| NPU | 2 tops | |
|
Camera |
Pixels | 1920 X 1080 pixels |
| Real-time Monitoring | Support | |
| Time-lapse Photography | Support | |
|
Sensors |
Remaining Filament Weight | Dynamic Monitoring |
| Filament Detection | Support | |
| Filament Clog Detection | Support | |
| Vibration Compensation | Support | |
| Auto-Leveling | Support | |
|
AI Lidar Detection |
First Layer Detection | Support |
| Accuracy Calibration | Support | |
| Flow Calibration | Support | |
|
AI Features |
Debris Detection | Support |
| Spaghetti Detection | Support | |
|
Energy Efficiency |
Screen auto sleep | Support |
| Printer auto power off | Support | |
| Smart Zone Heating | Support | |
| Power Off Resume Print Module | SupportCZ lift, protect model) | |
| Air Filter | Composite filter: HEPA + Activated Carbon | |
| System Upgrade | Upgrade Method | OTA |
|
Software |
Slicer | lsun Slicer, Third-Party Slicers |
| Supported OS | MacOS, Windows | |
| File Format | ST O 3 |
Component Introduction
Packing List
Accessory Box Packing List
Unboxing
Screen Installation
Connect And Power On
Language Settings
WiFi Settings
Calibrations
Loading Filament
First Printing
Customer Support
- Please go to flsun official website to download Flsun Slicer : Official website: https://flsun3d.com
Please visit the official Flsun Wiki for more information on machine use, maintenance and FAQs: http://wiki.flsun3d.com/en/home
By scanning the QR code you can choose any channel to get the latest product updates and related news.
- If you need additional assistance, please feel free to contact us:
After-sales e-mail: service@flsun3d.com
Go all the way forward and break through the limitations!
FCC
FCC Warning:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2) this device must accept any interterence received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
Bring the personalized production capacity to everyone’s desktop www.flsun3d.com
Documents / Resources
 |
FLSUN S1 Ultra High Speed 3D Printing [pdf] Instruction Manual S1, S1 Ultra High Speed 3D Printing, Ultra High Speed 3D Printing, High Speed 3D Printing, 3D Printing, Printing |