FLIR TA93 Multimeter Remote Controller User Manual

FLIR TA93 Multimeter Remote Controller

Overview

The TA93 remote controller lets you remotely freeze/unfreeze a connected FLIR digital multimeter’s displayed reading and capture images. It is battery-powered and clips onto one of the multimeter’s test leads, and must be paired with the supported meter before use.

Specifications

Setup and Use

1. Clip the TA93 remote controller onto one of the multimeter’s test leads.
2. For pairing, place the TA93 within 1 m (3.3 ft.) of the FLIR DM266.
3. On the DM266, press ENTER to open the Main Menu.
4. Go to Settings > Device Settings > Remote Control.
5. Press and hold both TA93 buttons and monitor the DM266 screen for status.
6. When pairing succeeds, the DM266 shows SUCCESS (or shows TIMEOUT after 20 seconds if pairing fails).
7. Release the held TA93 buttons.
8. To operate: press the TA93 Display Hold button to freeze/unfreeze the displayed reading.
9. To capture an image: press the TA93 Snapshot button.
10. Confirm button presses via the TA93 status LED flashing after each button press.

Introduction
The TA93 remote controller allows you to remotely freeze/unfreeze the displayed reading and capture images on select Flir digital multimeters (DMMs) like the Flir DM266. The TA93 is battery-powered and conveniently clips onto one of the multimeterʼs test leads.

Description

Figure 1:

• Snapshot button (1);
• Display Hold button (2);
• Status LED (3);
• Release tab for battery replacement (4);
• Test lead with TA93 attached (5).

Remote Control Pairing
The DMM and TA93 must be ‘pairedʼ before the remote controller can be used. The pairing process, provided below, applies only to the Flir DM266. For other meters, refer to the user manual provided with the meter, or contact customer support.

1. Place the TA93 within 1 m (3.3 ft.) of the DM266.
2. Press the DM266 ENTER button to open the Main Menu.
3. Scroll to ‘Settings’ and press ENTER.
4. Scroll to ‘Device Settings’ and press ENTER.
5. Scroll to ‘Remote Control’ and press ENTER.
6. Press and hold both TA93 buttons and monitor the DM266 screen for status.
7. The DM266 will indicate ‘pairing’ as it searches for the TA93 (see Figure 2 below).
8. When pairing is successful, the DM266 will indicate ‘SUCCESS’.
9. The DM266 will indicate ‘TIMEOUT’ (after 20 seconds) if pairing fails.
10. The DM266 will indicate ‘DONE’ for successful or unsuccessful pairing.
11. Release the held buttons.
12. If the pairing fails, ensure that the devices are placed within 1 m (3.3 ft.). Also, check the status of the TA93 battery (when the battery is fresh, the TA93 LED status indicator will light when either TA93 button is pressed).

Figure 2: Pairing the TA93 with the DM266 in the Device Settings menu.

Remote Controller Operation
When the remote controller is paired with a DMM, press the TA93 Display Hold button (item 2, in the Description section, above) to freeze or unfreeze the displayed DMM reading. Press the Snapshot button (item 1) to capture an image. Refer to the DMM user manual for information regarding media management and sharing. The TA93 status LED indicator (item 3) will flash after each button press.

Remote Controller Battery Replacement
The TA93 is powered by one CR1220 (3 V) coin battery. The battery requires replace-ment when the TA93 status LED no longer lights when either of its buttons is pressed. Follow the instructions in Figure 3 below to replace the battery. Note the position and orientation of the old battery before removing it, and orient the new battery similarly.Figure 3: Battery Replacement. Press the tab down (1); Slide the housing open (2); replace the battery (3). Secure the housing by sliding it back into the closed position.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference;
2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the userʼs authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the re-ceiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

IC Compliance
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadaʼs licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Customer Support
Repair, Calibration, and Technical Support: https://support.flir.com.

Warranty

10 Three-Year Warranty
This product is protected by FLIRʼs 3-Year Limited Warranty. Visit https://support.flir.com/prodreg to read the 3-Year Limited Warranty document.

• www.flir.com