FlightScope JR230 Mevo Range Launch Monitor
Specifications
- Part Number: E19-LQ265-ISSA
- Page Size: 150x100mm
- Color: CMYK
- Technology: FlightScope Fusion Tracking
- Tracking Technology: 3D Doppler radar and synchronized image processing
- Usage: Driving range or indoor simulator
- Mount: Semi-permanent baseplate mount
- Tracking Time: 12 hours
Product dimensions
*Total height with baseplate attached.
Battery Warning
CAUTION: This device contains a Li-ion battery. Do not be exposed to temperatures below freezing point. Do not be exposed to excessive heat. Avoid physical impact, puncture, crushing, or dropping. If the unit is struck by a club or ball, a short circuit or other heat reaction may occur, resulting in a fire.
Do not tamper with the battery pack. Avoid physical damage or stress when removing or inserting the battery. Do not short-circuit the battery terminals. Maintain battery condition by charging and discharging regularly, at least every few months. Use only the included charger and charging cable for best results. If the battery bulges, emits fumes or becomes very hot, disconnect it from the charger and replace the battery. Dispose of old batteries by applicable waste battery and recycling regulations.
Mevo Range
- On/Off button
- QR Code to connect a device (only used when the rear is not visible)
- QR Code to connect the device
- Indicators
- Alignment camera
- Hand grip
- Security port lock
- 12V Charging Connector
- Serial Sticker/ Frequency Band
- USB-A access hole
- USB Dongle (Wi-Fi)
Insert dongle before use
Placement
Place the unit on the baseplate. The unit will click into place magnetically.
Ensure the hexagon cap screws on the bottom of the unit align with the base plate. This will ensure the unit is facing the correct direction.
Unit facing the right direction and correctly aligned with the baseplate.
The unit aligned incorrectly with the baseplate.
Unit facing the wrong direction about the baseplate.
Connecting to the Mevo Range
- Scan the QR Code in your bay for the desired app.
- FS Golf app
A comprehensive and customizable phone app allowing users to teach, fit, and practice with radar data, video capabilities, 3D trajectories, and more.
- Data Margins & Instant Feedback
Set your minimum and maximum values for any data parameter to train smarter and improve consistency. Receive instant visual feedback with a simple green and red data display. - Data and Video Combined
Practice without interruption using the FS Golf App. The app on your phone will automatically record and clip each video before storing it on the app for easy review. - Customizable Trajectory View
Customize your trajectory screen display and preferred performance data blocks for the ultimate user experience.
- Data Margins & Instant Feedback
- FS Skills app
Evaluate your players with the most advanced and customizable combined assessments available.
- FlightScope Combines
Designed to be the ultimate and most advanced assessment of a golfer’s skill level. - Practice Smarter
Use Skills to determine accuracy and skill level for benchmarking and compare performance with players around the world. - Customized Challenges
Practice with a purpose by choosing target size, location, and point values for weaknesses.
- FlightScope Combines
- FS Golf app
- Switch on the unit by pressing the power button.
- Make sure your phone’s is turned ON.
- Open up the desired App.
- Scan the QR Code on the back of the unit to connect the App with the Mevo Range unit.
- Check that the radar connection status changes from Ready to Connected.
You are now ready to start your session.
Battery indicators
Have the battery charged if the level is <25% to ensure that your session can be completed.
System indicators
Important Notes
- The correct tee position is approximately 7’ (2.1 meters) directly in front of the Mevo Range unit.
- The base plate for the unit is fixed to the floor. Check that the hitting mat has not been moved from the correct position before playing.
- Extremely low and wide shots, and shots where the player is between the Mevo Range and the ball, might not register.
- Keep the area between Mevo Range and the ball position clear of any objects and people.
Frequency band
Switch off
- Press and hold the power button for 2 seconds to turn off the unit.
Lift unit
- Grab the unit using the recessed handle.
- Pull the unit forward whilst lifting to break the magnetic bond.
Technical specifications
| Transceiver | |
| Operating frequency | Fixed frequency in the 24,08 – 24,16z GHz band |
| Output power | 24 dBM +/-3dBm (North America); 17dBm +/-3dBm (Japan) |
| Antenna gain | 15.3 dB +/-1dB |
| Carrier modulation | CW/ None (NON) |
| Detection method | Doppler velocity measure- |
| Communication | |
| Data interfaces | USB 2.0 on a USB-A connector (Specified commercial USB Wi-Fi adapters may be used). |
| Electrical & Physical | |
| Operating temperature | 0°C to +40°C (operating, recommended) |
| Storage temperature | -10°C to +55°C (storage, non-operating) |
| Dimensions | 212 x 137 x 113mm |
| Mass | 3kg |
| Power supply/ charger | 12V dc +/- 10%; current up to 3.3A (lourens to confirm) |
| Charging time | 5 – 6hrs (recommended) |
| Battery (Optional) | 7.4V 13000mAh 96.2Wh |
FCC Statement
FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by FlightScope (PTY) could void the user’s authority to operate the equipment. To comply with FCC and ISED RF Exposure requirements, a minimum separation distance of 20 cm must be maintained between the device and all persons during normal operation.
ISED Statement: This device contains license-exempt transmitters(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’slicense-exemptt RSS(s). Operation is subject to the following conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
CONTACT DETAILS
Office phone number:
Mevo Series: +1 407 967 7121
X-Series: +1 407 664 2622
Email: support@flightscope.com
Company address: 8600 Commodity Cir #106, Orlando, FL 32819, United States
Country of Origin: South Africa
FAQs
Battery Warning
Q: How can I know when the battery is low?
A: The battery warning indicator will notify you when the battery is running low.
App Connectivity
Q: How do I connect the Mevo Range unit to the FS Golf or FS Skills app?
A: Scan the QR code on the back of the unit using the desired app to establish a connection.
Data Parameters
Q: What data parameters can I track with the Mevo Range unit?
A: The device provides various data parameters such as trajectory, speed, distance, and more for performance analysis.
Documents / Resources
 |
FlightScope JR230 Mevo Range Launch Monitor [pdf] User Manual JR230, QXP-JR230, QXPJR230, JR230 Mevo Range Launch Monitor, JR230, Mevo Range Launch Monitor, Range Launch Monitor, Launch Monitor, Monitor |
