FLEETFLIX Plus Pro Dash Camera
Product Specifications
- Product Name: FleetFlix AI+
- Features: LED Indicator, Camera Start/Bootup, Live Stream, Firmware Update, Stand By, Recording, Alert Button
- Mounting: Truck Mount Clip and Adhesive Tape
- Storage: Micro SD card (provided by Fleet Hoster)
- Connection: OBD II Connector
Product Usage Instructions
LED Indicator States
- Camera Start/Bootup: All 3 lights flashing (Red, Orange, and Green)
- Live Stream: Flashing Green
- Firmware Update/Mobile Network Startup: Red flashing and Solid Green
- Stand By: Solid Red
- Camera Online and Recording: Solid Green
- Offline: No Lights
- Camera Online and Not Recording/SD Error: Red and Orange Flashing
- Sensor/GPS Error: Red and Orange flashing, Solid Green
Alert Button
The FleetFlix AI+ comes with a record button on the rear panel. A brief press captures media from cameras, while a press over 3seconds triggers an audio alert. During installation, use the button for calibration. Once successful, it returns to normal function.
Mounting Instructions
Mount the FleetFlix AI+ using the Truck Mount Clip or Adhesive Tape provided.
Micro SD Card Installation
The camera supports automatic recording to a Micro SD card provided by Fleet Hoster. Insert the SD card into the slot under the right panel I/O cover.
OBD II Connector Setup
- Refer to the vehicle’s manual to locate the OBD II connector.
- Connect the OBD II Power Cable to the blade fuse holder cable according to the color guide provided.
- Feed the 12-pin connector through the hole on the right panel I/O cover and plug it into the OBD II connector in the vehicle.
LAYOUT DIAGRAM
Front panel 1/0 layout
Rear panel 1/0 layout
The Fleetflix Al+ comes with a speaker located on the left panel.
LAYOUT DIAGRAM
Figure 4: Right panel 1/0 layout
The Fleetflix Al+ comes with a microphone located on the bottom panel. The diagram of the microphone is shown below.
Figure 5: Bottom panel 1/0 layout
PRODUCT DIMENSIONS
External 1/0 Pin Descriptions and Functionality
The FleetFlix Al+ Dash Cam features several interfaces, including a Micro USB 2.0 port (debugging),
Micro SD card slot, Micro SIM card slot, and 12-pin power connector.
Micro USB 2.0 Port
The FleetFlix Al+?is equipped with one Micro USB 2.0 port located on the right panel for debugging.
The pinouts of the Micro USB port are shown below.
| Pin | Signal |
| 1 | VBUS |
| 2 | D- |
| 3 | D+ |
| 4 | ID |
| 5 | GND |
Micro SIM Card Slot
ThFleetFlix Al+ + comes with a Micro SIM card slot located on the right panel that can support a 4G
SIM card. The pinouts of the Micro SIM card slot are shown below.
| Pin | Signal |
| 1 | DAT2 |
| 2 | CD/DAT3 |
| 3 | CMD |
| 4 | VDD |
| 5 | CLK |
| 6 | vss |
| 7 | DATO |
| 8 | DATl |
Micro SIM card slot pinouts
Micro SIM Card Slot
ThFleetFlix Al+ + comes with a Micro SIM card slot located on the right panel that can support a 4G
SIM card. The pinouts of the Micro SIM card slot are shown below.
| Pin | Signal |
| Cl | VDD |
| C2 | RST |
| C3 | CLK |
| cs | vss |
| C6 | NC |
| Cl | DATA |
3: Micro SIM card slot pinouts
Pin Power Connector
ThFleetFlix Al+i+ comes with a 12-pin power connector. The 12-pin power connector is used for
supplying power to tkFleetFlix Al+ j+. The pinouts of the 12-pin power connector are shown below.
| Pin | Signal |
| Cl | VDD |
| C2 | RST |
| C3 | CLK |
| cs | vss |
| C6 | NC |
| Cl | DATA |
4: 12-pin power connector pinouts
LED Status
The FleetFlix Al+ comes with three LED indicators located on the rear panel to show the status. The three LED indicator states are shown in the diagram below.
LED Indicator States
Caelirtb raButte to Anlert Button
The FlFleeeteFtliFlxi xA IA+I +comes with a short record button on the rear panel of the camera. When pushed briefly, the camera will capture media from the internal and external cameras. When pushed for more than 3 seconds, an audio alert will be triggered. During install, this button is used for the calibration process, a brief press will trigger. Once the calibration is successful, the button will return to normal functionality.
Accessories
The following cables and mounting brackets are included with your FleetFlix Al+;
FleetFlix AI+ Truck Mount Clip and Adhesive Tape Mounting Brackets
Installation
This chapter provides information about the Fleetflix Al+ installation procedures. (If the camera comes pre-installed with SD and SIM cards, skip to installing the cables.)
Removing the Right Panel 1/0 Cover
Step 1
Loosen the screw of the right panel 1/0 cover with the included allen wrench.
Loosen the screw of the right panel 1/0 cover
Step 2
Remove the right panel 1/0 cover.
Installing the Micro SD Card
The FleetFlix AI+ dash cam supports automatic video recording to a Micro SD card after startup. The camera must use a Micro SD card provided by Fleet Hoster. If another SD card is used, the camera will not work. The SD card typically comes pre-loaded within the FleetFlix device but can be accessed if needed via the Micro SD card slot under the right panel I/O cover.
Locate the Micro SD card slot.
Locating the Micro SD card slot
Step 2
Insert a Micro SIM card into the Micro SIM card slot. Use your fingernail to press the card into the slot. When it is fully inserted, the card will snap into the slot.
Installing the 4G Micro SIM Card
(If the camera comes pre-installed with SD and SIM cards, skip to installing the cables.)
The ÉieefFfix Ai+}dash cam can download maps through a 4G network. To use this feature, you need to insert a 4G into the Micro SIM card slot on the Fleetflix Al.
Step 1
Locate the Micro SIM card slot.
step 2
Insert a 4G Micro SIM card into the Micro SIM card slot. Use your fingernail to press the card into the slot.
When it is fully inserted, the card will snap into the slot.
Installing the Cables
Using the OBD II Power Cable
Reference the vehicle’s user manual to find the location of the OBD II connector. Locate the OBD port of the vehicle and directly connect with the port.
Plug in the OBD II Power Cable to the OBD II connector in the vehicle.
Wire Color Guide for OBD Harness
Remove the right panel I/O cover. For details, refer to section 3.1. Feed the 12-pin connector of the 0BD II Power Cable through the hole on the right panel 1/0 cover.
Feeding the 12-pin connector cable through the hole on the 1/0 cover
Plugging in the 12-pin connector of the 0BD II Power Cable
Reinstall the right panel 1/0 cover. Make sure to tighten the screw.
Reinstalling the right panel 1/0 cover
OBD II power cable’s connectors
| 12-Pin Power Connector |
ACC Connector |
OBD II Connector |
CableAWG |
|
| Signal Name | Pin No. | Pin No. | Pin No. | UL Type and Color |
| B+ | 2&4 | – | 16 | UL1007 22AWG Red and Blue |
| GND | 8 | – | 5 | UL1007 22AWG Black |
| ACC-IN | 6 | 1 | – | UL1007 22AWG Yellow |
| (Connect to vehicle’s Fuse Box) | ||||
| CAN_L | 12 | – | 14 | UL1007 26AWG White |
| CAN _H | 10 | – | 6 | UL1007 26AWG Green |
| – | 1, 3, 5, 7, 9 & 11 | – | 1, 2, 3, 4, 7, 8, 9, 10, 11, I –
12, 13 & 15 |
|
OBD II power cable’s connector pinouts
Reminder:
After connecting the ACC connector of the OBD II power cable to the Bladed Fuse Holder cable, slide on the plastic protective covers to cover the connection point.
Mounting
Step 1
Attach the adhesive tape mounting bracket onto the FleetFlix Al+.
Step 2
Install the device in the center of thdash shieldld, below the rearview mirror. (It is recommended to use Alcohol to clean the glass before mounting the device.)
Measurement Guide for Camera Callibration
After installation is complete, the following measurements are needed:
- Length from Camera Mount to Front of Vehicle (in) – the distance from the front lens of the camera and the front bumper
- Width of Vehicle (in) – the total width of the vehicle at its widest point in front of the camera (typically wheel arch to wheel arch
- Height from Camera Mount to Ground (in) – the distance from the ground to the bottom of the camera
Entering Measurements into FleetFlix AI+ Add-in
- Once the proper measurements are gathered, enter the measurements into the FleetFlix Add-in under the “Measurements” tab in the Cameras settings.
- To get to the “Measurements” tab, click “Cameras” under the Geotab FleetFlix Add-in.
- Next, select the “Settings” icon under the “Actions” column for the specific camera measurements that were taken.
- Finally, click the “Measurements” tab, enter the measurements, and then click “Save.”
To Start Calibration
The vehicle should be driven on the following road parameters:
- Good contrast for lane markers
- Capable of supporting 30+ mph for 3-5 minutes
- Avoid hills or turns
- Reasonable weather
- Light traffic
Step 1
While driving down the road, press and hold the calibrate/alert button (pictured below) on the camera for 3 seconds. The camera will announce “Calibration Started.”
Step 2
The vehicle will need to be driven for a few minutes during the calibration process.
Step 3
After the vehicle is driven within these parameters, the camera will announce “Calibration Successful”. After calibration is complete, the calibrate/alert button will return to the driver alert function.
If the camera is ever removed or unmounted, calibration will need to be completed again.
FAQS
- Q: What should I do if the camera shows an SD error?
A: If the camera displays an SD error, check if the Micro SD card is correctly inserted. Ensure it is the one provided by Fleet Hoster. - Q: How do I know if the camera is recording?
A: When the LED indicator shows solid green, the camera is online and actively recording.
Documents / Resources
 | Plus Pro Dash Camera |
References
- User Manualmanual.tools