FIT 501301,501303 Master Node Basic Plus
Specifications
Fit Master Node Basic
- Control elements and display
Fit Remote Pure Left
- Control elements
Pinion TE1 E-Trigger
Intended Use: To be used with the Fit Master Node Basic and Fit Remote Pure Left for electric drive systems.
Technical Data
- Fit Master Node Basic
- Fit Remote Pure Left
Initial Operation
- Power on the Fit Master Node Basic.
- Connect the Fit Key Card with the Fit E-Bike Control App.
Assistance Modes
Trailing: Description of trailing mode and how to activate it.
Pushing Aid: Explanation of pushing aid mode and its activation process.
3.1 GENERAL INFORMATION
Please read all safety instructions carefully. Failure to comply with the warnings or take residual risks into account may result in electric shock, fire and/or serious injury.
Keep the operating instructions in a safe place and have them readily available to consult. Pass these instructions on if you provide your e-bike for someone else’s use.
The generic names used in these operating instructions, such as motor, battery and operating element, all refer to original FIT e-bike components.
3.2 CONTROL ELEMENT AND FIT MASTER NODE BASIC
Don’t let yourself be distracted by the LED display. If you don’t concentrate fully on traffic, you risk becoming involved in an accident.
Do not open either the control element or the FIT Master Node Basic. They can be damaged if they are opened and any warranty claims will be forfeited.
Caution! Using the FIT Master Node Basic with Bluetooth may interfere with other devices and equipment, aircraft and medical devices (e.g. pacemakers, hearing aids). Nor can any injury to humans and animals in the immediate surroundings be fully ruled out. Avoid operating for prolonged periods of time very close to your body. Pay attention to any local restrictions on its use, e.g. in aircraft, hospitals, near medical equipment, petrol stations, chemical installations, areas where there is a risk of explosions and in blasting areas.
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
6
INSTRUCTION MANUAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
4 PRODUCT AND TECHNICAL SPECIFICATIONS
4.1 FIT MASTER NODE BASIC
The FIT Master Node Basic controls the e-bike system and uses LEDs to indicate the assistance level and the charge level of the e-bike battery. The Master Node Basic is installed in the upper tube of the e-bike. The Master Node Basic is secured with a spring at the top and a screw at the bottom. There are 3 buttons on the Master Node Basic. One button to switch the e-bike on or off, and two buttons to select the desired assistance level.
4.1.1 CONTROL ELEMENTS AND DISPLAY
1. Battery charging status 2. On/off/light button 3. Current assistance level 4. Decrease assistance button 5. Increase assistance button
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
7
INSTRUCTION MANUAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
4.2 FIT REMOTE PURE LEFT
The FIT Remote Pure with ring control and function button is the ideal accessory for every e-bike rider who wants full control of their assistance level. The ring on the remote enables intuitive control of the assistance level by simply rotating it. The desired assistance level can be selected by turning the ring up or down. The function button on the remote is easy to use and offers quick access to other functions that can be selected via the app.
4.2.1 CONTROL ELEMENTS
1. Function button (The default configuration is the Boost function. Other configurations can be adjusted via the FIT E-Bike Control app.)
2. Ring down 3. Ring up
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
8
INSTRUCTION MANUAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
4.3 PINION TE1 E-TRIGGER
The compact Pinion TE1 e-trigger gear lever has been specially developed for shifting with Pinion Smart.Shift shift technology. The goal was to provide clear haptic feedback. With a defined lever path and sophisticated micro button tuning, you can precisely initiate each shifting process. Maintenance-free and waterproof as defined by IP66, the TE1 is the optimal control in every situation.
1. Rear gear lever 2. Front gear lever 3. Matchmaker clamp with screw 4. Blind screw 5. Plug
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
9
INSTRUCTION MANUAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
4.4 INTENDED USE
The FIT Master Node Basic and the FIT Remote Pure Left are designed for controlling a FIT e-bike system and displaying riding data.
4.5 IMPROPER USE
Improper use refers to use which is not described under proper use or goes beyond proper use.
4.6 TECHNICAL DATA
4.6.1 FIT MASTER NODE BASIC
Product code
Operating tempera- °C
ture
Storage tempera- °C
ture
Protection class
Weight about
kg
FIT Master Node Basic 501301 -10 to +40
-20 to+50
IPX5 0.043
4.6.2 FIT REMOTE PURE LEFT
Product code Operating temperature Storage temperature Protection class Weight about
FIT Remote Pure Left 501303 °C -10 to +40
°C -20 to +50
IPX7 kg 0.028
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
10
INSTRUCTION MANUAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
5 OPERATION
5.1 INITIAL OPERATION
5.1.1 ELECTRIC DRIVE SYSTEM
SWITCHING ON THE ELECTRIC DRIVE SYSTEM The system can only be switched on if a sufficiently charged battery is installed. Press the on/off/light button for at least one second to switch the system on. The assistance level display briefly lights up in magenta for confirmation.
SWITCHING OFF THE ELECTRIC DRIVE SYSTEM If the system does not detect any rider activity for a long time, it switches off automatically to save energy. To turn off the electrical system manually, press the on/off/light button for at least one second. The assistance level display briefly lights up in magenta for confirmation.
OPERATION You can select the assistance level with the Increase/decrease assistance buttons on the FIT Master Node Basic or by ring up/down on the FIT Remote Pure Left . More adjustment options will be available soon via the FIT E-Bike Control app.
5.1.2 PAIRING/COUPLING THE FIT KEY CARD WITH THE FIT E-BIKE CONTROL APP
The FIT Key Card is your ticket to the digital FIT world for every e-bike with FIT 2.0 integration. The individual ID is based on the SmartX technology from ABUS and ensures a secure connection to the e-bike with a unique key.
INFO-CIR
NOTICE Keep the card in a safe place as it serves as the e-bike’s ID. Can be reordered subject to payment in the e-shop if lost.
Select the menu E-bikes in the navigation bar Press the + icon to add your e-bike in the FIT E-Bike Control app
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
11
INSTRUCTION MANUAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
Follow the instructions in the FIT E-Bike Control app
5.2 ASSISTANCE MODES
You can adjust the assistance level with the buttons Decrease assistance/increase (FIT Master Node Basic) and Ring Down/Up (FIT Remote Pure Left). Each assistance level has a specific position to make things easier for riders who are color blind. FLY
Maximum motor assistance for active riding up to high pedaling frequencies.
FLEX
Motor assistance is perfect for E-MTB trails or very agile e-bikes.
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
12
INSTRUCTION MANUAL FLOW
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
Motor assistance for energy-saving cross-country trips or moderate off-road terrain
ECO Minimal motor assistance with optimum efficiency for maximum range.
OFF
No motor assistance. The e-bike rides like a normal bicycle. All on-board computer functions are available.
5.2.1 TRAILING
Trailing ensures that the motor assistance remains active for a short time when you stop pedaling. The pre-set trailing makes the power delivery of the Pinion MGU even more harmonious and natural for city and trekking e-bikes, as the lack of force with the vertical pedal position at low cadence is easily overcome. In technically demanding situations and in the event of obstacles on the terrain, the riding pace is noticeably improved with trailing, should you decide to stop pedaling. If you deactivate this feature, the MGU immediately stops the motor assistance once you stop pedaling.
INFO-CIR
NOTICE Trailing is activated by default, and can be deactivated only via the FIT E-Bike Control App. To use the FIT E-Bike Control App, your smartphone must be connected to the e-bike using a FIT Key Card (see Section l 5.1.2).
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
13
INSTRUCTION MANUAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
5.2.2 PUSHING AID (Only available in conjunction with FIT Remote Pure left.)
Pushing aid mode enabled: all LEDs light up white. Pushing aid started: the white island moves up slowly.
The pushing aid makes it easier to push the e-bike. The e-bike can be moved out of underground parking or along steep paths comfortably by activating the pushing aid. To activate the pushing aid mode, press the ring on the FIT Remote Pure left until the white LED display appears at the top. The pushing aid is started by pressing up again and holding the ring on the FIT Remote Pure left. If you release the ring on the FIT Remote Pure left for longer than five seconds, you will quit the pushing aid mode. The choice of gear affects the force that is applied and speed of the pushing aid. Always use first speed for the pushing aid to protect the drive.
Exclamat
CAUTION When using the pushing aid, the wheels must be in contact with the ground to avoid the risk of injury.
5.2.3 BOOST FUNCTION (Only available in conjunction with FIT Remote Pure Left.)
All LEDs are magenta and 1 slightly darker LED moves up quickly.
You can temporarily increase the motor assistance to FLY with the boost function, no matter what assistance level is set (ECO, FLOW, FLEX) . This function can be activated at speeds of 7 km/h and over and if at least one quarter pedal revolution has been detected. The Boost function cannot be used if the pushing aid mode is active. . In order to activate the Boost function (only possible while riding), press and hold down either the function button or the ring up on the FIT Remote Pure Left. The Boost function is activated as long as the ring or button is held down.
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
14
INSTRUCTION MANUAL
5.3 LIGHTS
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
On: LEDs come on in white from the bottom to the top and then disappear again. Off: LEDs come on in white from top to bottom and then disappear again.
The lights are switched on or off by briefly pressing the on/off/light button of the FIT Master Node Basic. Various lighting systems are installed depending on the area of use and bicycle type. If this has a daytime running light function, the system will always switch automatically between low beam and daytime running light.
5.4 E-SHIFT
Use the up/down buttons on the gear shift to select the gear manually. You can switch to or exit the automatic mode selected in the settings menu (Auto.Shift or Auto.Shift.Pro) by pressing and holding the button (3 seconds) on the front lever of the Pinion TE1 e-trigger.
The gearbox provides assistance with 9-speed and 12-speed. You can shift through multiple gears at once (e.g. from 06 to 02). Changing gears while stationary or when the crank is at rest or rotating backward is possible, and protects the gearbox.
Shifting down (12-11-10 … -01): Possible to a limited extent under load-bearing. Shifting will not be available if there is too much pressure on the pedal.
Shifting up (01-02-03 … -12): A mechanism in the gearbox allows you to shift up under load; the pressure needs to be briefly released from the pedal only when changing between the respective sub-gearboxes.
For P1.9 motor only: When shifting up from 03 to 04 and from 06 to 07, always make sure to release any pressure from the pedal.
For P1.12 motor only: When shifting up from 04 to 05 and from 08 to 09, always release pressure from the pedal.
INFO-CIR
NOTICE Occasionally, the crank may «drop» after a gear shift by about 10°, causing a brief jerk until the shifter pawl engages in the next tooth. This is normal and does not damage the gearbox.
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
15
INSTRUCTION MANUAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
AUTO.SHIFT
In Auto.Shift mode, the up/down button (e.g. Pinion TE1 E-Trigger) is used to reduce/increase the cadence (pedal frequency).
AUTO.SHIFT.PRO
Auto.Shift.Pro is designed for sporty, dynamic riding and automatically changes to the gear that matches your cadence (pedaling frequency) defined in the settings menu. In contrast to Auto.Shift mode, with Auto.Shift.Pro you use the control unit (e.g. Pinion TE1 E-Trigger) not only to adjust the cadence, but also to override automatic mode and manually set the desired speed in every situation.
If you change gear manually in Auto.Shift.Pro mode, the system registers your current cadence and adjusts the automatic gear shifting according to your preference. If you want to return to the original cadence (the number in the settings menu) while riding, you can do this by pressing and holding the button (3 seconds) on the rear lever of the Pinion TE1 E-Trigger.
INFO-CIR
NOTICE With the FIT E-Bike Control App, you have full control over your E-Shift functions. Either the current gear or the status of Auto.Shift or Auto.Shift.Pro is displayed on the FIT Drive Screen. You can adjust all electronic shifting settings directly in the app. To use the FIT E-Bike Control App, your smartphone must be connected to the e-bike using a FIT Key Card (see Section l 5.1.2).
5.5 STATE OF CHARGE OF THE BATTERY
5.5.1 IN OPERATION
80 to 100% charge Each battery charging status LED that comes on represents approximately 20% of the battery capacity.
5 to 9% charge The lowest LED flashes slowly
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
16
INSTRUCTION MANUAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
1 to 4% charge The lowest LED flashes quickly
0% charge The lowest LED flashes quickly and the assistance level LEDs light up red.
5.5.2 DURING CHARGING
Each battery charging status LED that comes on represents approximately 20% of the battery capacity. The top battery charging status LED indicates the current charge level by pulsing.
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
17
INSTRUCTION MANUAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
5.6 ACCESSORIES
5.6.1 BIKE LOCK WITHOUT ELECTRONIC LOCK (Only via FIT E-Bike: Control app or hand-held transmitter)
CLOSE LOCKING finished : All LEDs flash blue 4x quickly. LOCKED: All LEDs light up steady blue.
OPEN UNLOCKING finished: All LEDs flash green 4x quickly, then light up steady green.
5.6.2 BIKE LOCK WITH ELECTRONIC LOCK (Only via FIT E-Bike: Control app or hand-held transmitter)
CLOSE LOCKING: All LEDs flash repeatedly 2x blue. LOCKING finished: All LEDs flash blue 4x quickly. LOCKED: All LEDs light up blue.
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
18
INSTRUCTION MANUAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
OPEN UNLOCKING: All LEDs flash repeatedly 2x green. UNLOCKING finished: All LEDs flash green 4x quickly, then light up steady green.
5.7 SPECIAL OPERATING MODES
5.7.1 MAINTENANCE MODE
No battery display. All LEDs pulse gently in white always at full brightness The FIT Master Node Basic has to be restarted to quit the Maintenance mode.
5.7.2 OEM, TEST, NOT FOR SALE MODE
The upper and lower LEDs flash alternately in green and red when starting up.
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
19
INSTRUCTION MANUAL 5.7.3 SOFTWARE UPDATE MODE
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
Every second LED on the motor assistance indicator lights up green and every second LED on the battery indicator lights up white.
5.8 SIGNAL TONES
Beep Short high note Falling sound sequence Two low notes
Meaning
Highest assistance level reached Battery level low
Error/Critical error
Situation
Sounds when you try to raise the assistance level even further in the assistance level FLY Sounding at 5% charging status and again at 0% Sounds in case of an error or a critical error (no motor assistance)
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
20
INSTRUCTION MANUAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
6 ERROR MESSAGES
6.1 GENERAL
The parts of the e-bike system are constantly monitored for errors during use and charging.
6.2 ERROR DISPLAY
LEDs flash orange. No motor assistance The motor assistance is not available again until the error has been remedied and the system restarted.
6.2.1 ERROR TABLE You can get more detailed information about the error with the FIT Drive Screen in the FIT E-Bike Control app.
If the last two digits are listed with “xx” as placeholders, they help the specialist dealer as additional information for error analysis.
0A-xx up to 28-xx
Error code 0A-01, 0B-01 0A-02, 0B-02
0A-03, 0A-04, 0A-05, 0A-06, 0B-03, 0B-04, 0B-05, 0B-06
0A-07, 0B-07 0A-08, 0B-08
Error description Remote motor communication error Remote display communication error
Remote battery communication error
Remote speed node communication error Remote gears communication error
Action/Restriction
1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Switch the system off. 3. Remove display from holder, check contacts and
clean if necessary. 4. Re-insert the display and start the system. 5. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Switch the system off. 3. Remove the battery from the holder, check
contacts and clean if necessary. 4. Re-insert the battery and start the system. 5. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer.
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
21
INSTRUCTION MANUAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
Error code
Error description
Action/Restriction
0A-0A, 0B-0A
0A-0B, 0B-0B 0C-00 0C-01 0C-02
0C-03, 0C-04, 0C-05, 0C-06 0C-07 0C-08 0C-0A
0C-0B 0D-01
Remote charger communication error
Remote lock communication error Remote identification error Remote motor identification error Remote display identification error
Remote battery identification error
Remote speed node identification error Remote gears identification error Remote charger identification error
Remote lock identification error Motor authentication error
1. Restart the system. 2. Switch the system off. 3. Disconnect the charger from the system and
socket. 4. Wait until status LED goes out. 5. Check plug contacts on the e-bike and charger
and clean if necessary. 6. Reconnect the charger to the socket. 7. Reconnect the charger to the system and start
the system. 8. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Switch the system off. 3. Remove display from holder, check contacts and
clean if necessary. 4. Re-insert the display and start the system. 5. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Switch the system off. 3. Remove the battery from the holder, check
contacts and clean if necessary. 4. Re-insert the battery and start the system. 5. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Switch the system off. 3. Disconnect the charger from the system and
socket. 4. Wait until status LED goes out. 5. Check plug contacts on the e-bike and charger
and clean if necessary. 6. Reconnect the charger to the socket. 7. Reconnect the charger to the system and start
the system. 8. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer.
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
22
INSTRUCTION MANUAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
Error code 0D-02
0D-03, 0D-04, 0D-05, 0D-06
0D-07 0D-08 0D-0A
0D-0B 0E-xx 0F-00 0F-01 0F-02
0F-03, 0F-04, 0F-05, 0F-06
Error description Display authentication error
Battery authentication error
Speed node authentication error Gears authentication error Charger authentication error
Lock authentication error Remote authentication error Remote update error Motor update error Display update error
Battery update error
Action/Restriction
1. Restart the system. 2. Switch the system off. 3. Remove display from holder, check contacts and
clean if necessary. 4. Re-insert the display and start the system. 5. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Switch the system off. 3. Remove the battery from the holder, check
contacts and clean if necessary. 4. Re-insert the battery and start the system. 5. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Switch the system off. 3. Disconnect the charger from the system and
socket. 4. Wait until status LED goes out. 5. Check plug contacts on the e-bike and charger
and clean if necessary. 6. Reconnect the charger to the socket. 7. Reconnect the charger to the system and start
the system. 8. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Switch the system off. 3. Remove display from holder, check contacts and
clean if necessary. 4. Re-insert the display and start the system. 5. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Switch the system off. 3. Remove the battery from the holder, check
contacts and clean if necessary. 4. Re-insert the battery and start the system. 5. If the problem persists, please contact your
specialist dealer.
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
23
INSTRUCTION MANUAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
Error code 0F-07 0F-08 0F-0A
0F-0B 10-xx 11-xx 12-01 12-02
12-03, 12-04, 12-05, 12-06
12-07 12-08
Error description Speed node update error Gears update error Charger update error
Lock update error Remote software error Battery remote communication error Remote motor pairing error Remote display pairing error
Remote battery pairing error
Remote speed node pairing error Remote gears pairing error
Action/Restriction
1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Switch the system off. 3. Disconnect the charger from the system and
socket. 4. Wait until status LED goes out. 5. Check plug contacts on the e-bike and charger
and clean if necessary. 6. Reconnect the charger to the socket. 7. Reconnect the charger to the system and start
the system. 8. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Switch the system off. 3. Remove display from holder, check contacts and
clean if necessary. 4. Re-insert the display and start the system. 5. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Switch the system off. 3. Remove the battery from the holder, check
contacts and clean if necessary. 4. Re-insert the battery and start the system. 5. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer.
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
24
INSTRUCTION MANUAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
Error code
Error description
Action/Restriction
12-0A
12-0B 13-xx 14-xx 15-01 15-02
15-03, 15-04, 15-05, 15-06 15-07 15-08 15-0A
15-0B
Remote charger pairing error
Remote lock pairing error Remote internal error Remote configuration error Remote motor pairing error Remote display pairing error
Remote battery pairing error
Remote speed node pairing error Remote gears pairing error Remote charger pairing error
Remote lock pairing error
1. Restart the system. 2. Switch the system off. 3. Disconnect the charger from the system and
socket. 4. Wait until status LED goes out. 5. Check plug contacts on the e-bike and charger
and clean if necessary. 6. Reconnect the charger to the socket. 7. Reconnect the charger to the system and start
the system. 8. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Switch the system off. 3. Remove display from holder, check contacts and
clean if necessary. 4. Re-insert the display and start the system. 5. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Switch the system off. 3. Remove the battery from the holder, check
contacts and clean if necessary. 4. Re-insert the battery and start the system. 5. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Switch the system off. 3. Disconnect the charger from the system and
socket. 4. Wait until status LED goes out. 5. Check plug contacts on the e-bike and charger
and clean if necessary. 6. Reconnect the charger to the socket. 7. Reconnect the charger to the system and start
the system. 8. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer.
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
25
INSTRUCTION MANUAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
Error code 16-00 16-01 16-02
Error description Remote theft detection Motor theft detection Display theft detection
16-03, 16-04, 16-05, 16-06
Battery theft detection
16-07 16-08 16-0A
Speed node theft detection Gears theft detection Charger theft detection
16-0B 17-00 17-01 17-02
Lock theft detection Remote defective component Motor defective component Display defective component
Action/Restriction
1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Switch the system off. 3. Remove display from holder, check contacts and
clean if necessary. 4. Re-insert the display and start the system. 5. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Switch the system off. 3. Remove the battery from the holder, check
contacts and clean if necessary. 4. Re-insert the battery and start the system. 5. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Switch the system off. 3. Disconnect the charger from the system and
socket. 4. Wait until status LED goes out. 5. Check plug contacts on the e-bike and charger
and clean if necessary. 6. Reconnect the charger to the socket. 7. Reconnect the charger to the system and start
the system. 8. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Switch the system off. 3. Remove display from holder, check contacts and
clean if necessary. 4. Re-insert the display and start the system. 5. If the problem persists, please contact your
specialist dealer.
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
26
INSTRUCTION MANUAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
Error code 17-03, 17-04, 17-05, 17-06
17-07 17-08 17-0A
17-0B 18-00 18-01 18-02
18-03, 18-04, 18-05, 18-06
18-07 18-08
Error description Battery defective component
Speed node defective component Gears defective component Charger defective component
Lock defective component Remote start error Motor start error Display start error
Battery start error
Speed node start error Gears start error
Action/Restriction
1. Restart the system. 2. Switch the system off. 3. Remove the battery from the holder, check
contacts and clean if necessary. 4. Re-insert the battery and start the system. 5. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Switch the system off. 3. Disconnect the charger from the system and
socket. 4. Wait until status LED goes out. 5. Check plug contacts on the e-bike and charger
and clean if necessary. 6. Reconnect the charger to the socket. 7. Reconnect the charger to the system and start
the system. 8. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Switch the system off. 3. Remove display from holder, check contacts and
clean if necessary. 4. Re-insert the display and start the system. 5. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Switch the system off. 3. Remove the battery from the holder, check
contacts and clean if necessary. 4. Re-insert the battery and start the system. 5. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer.
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
27
INSTRUCTION MANUAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
Error code 18-0A
18-0B 19-xx 1A-01
1A-02
1B-xx
1C-xx
1D-xx 1E-xx 1F-xx 20-xx 21-xx 22-xx 23-09
Error description Charger start error
Lock start error Remote safety error Manipulation detected
Manipulation detected Speed sensor missing System voltage error
Bluetooth module error
EMS mode active OEM mode active TEST mode active Reserve mode active (info text) Lock error Full charge cycle active Tire pressure sensor error Battery weak front
Action/Restriction
1. Restart the system. 2. Switch the system off. 3. Disconnect the charger from the system and
socket. 4. Wait until status LED goes out. 5. Check plug contacts on the e-bike and charger
and clean if necessary. 6. Reconnect the charger to the socket. 7. Reconnect the charger to the system and start
the system. 8. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Check mounting position of the magnet and
speed sensor. 2. Restart the system. 3. If the problem persists, please contact your
specialist dealer. 1. Check mounting position of the magnet and
speed sensor. 2. Restart the system. 3. If the problem persists, please contact your
specialist dealer. 1. Check whether the correct battery is installed
(36V/48V). 2. Restart the system. 3. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Restart FIT E-Bike Control (app), update if
necessary. 3. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Charge the battery. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. Information: Battery is charged for calibration despite Long Life mode 100%.
Sensor needs to be replaced soon, please contact your specialist dealer.
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
28
INSTRUCTION MANUAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
Error code 23-0A 23-0B 23-0C 23-xx 24-01
25-xx
26-xx
Error description Tire pressure sensor error Battery weak rear Tire pressure sensor error Battery weak front right Tire pressure sensor error Battery weak rear right Tire pressure sensor error
Charger multi-battery error
1-Wire communication error
Battery lock (ABUS) error
29-xx up to 47-xx
Error code 29-xx
2A-xx
Error description Display communication error
Display software error
2B-xx
Display authentication error
2C-xx 2D-xx
Display internal error Display identification error
2E-01
Display overheated Screen brightness reduced
48-xx 66-xx (Pinion)
Action/Restriction
Sensor needs to be replaced soon, please contact your specialist dealer.
Sensor needs to be replaced soon, please contact your specialist dealer.
Sensor needs to be replaced soon, please contact your specialist dealer.
Sensor may need to be replaced, please contact your specialist dealer.
1. Charge each battery individually. 2. Have the charger software update done at your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer.
Action/Restriction
1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Switch the system off. 3. Remove display from holder, check contacts and
clean if necessary. 4. Replace the display and start the system. 5. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Switch the system off. 3. Remove display from holder, check contacts and
clean if necessary. 4. Replace the display and start the system. 5. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Switch the system off. 3. Remove display from holder, check contacts and
clean if necessary. 4. Replace the display and start the system. 5. If the problem persists, please contact your
specialist dealer. 1. Cool display by riding. 2. Protect the display from direct sunlight.
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
29
INSTRUCTION MANUAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
Error code 48-xx
Error description Motor communication error
49-07
Motor error E-bike battery not ready
49-09, 49-0A
Motor error
49-0B 49-0C
Motor error Pinion change detected
Motor error Tampering detected
49-0D
Motor error
49-xx 4A-xx
Motor error Motor temperature error
4B-xx 4C-xx
Motor speed sensor error Motor torque sensor error
Action/Restriction
1. Check plug contacts on the battery and bicycle and clean if necessary.
2. Restart the system. 3. If the problem persists, please contact your
specialist dealer. 1. Switch the system off. 2. Remove the battery. 3. Check plug contacts on the battery and e-bike
and clean if necessary. 4. Insert the battery. 5. Restart the system. 6. If the problem persists, please contact your
specialist dealer. 1. Check if one or both trigger buttons are pressed
constantly, if so: Release buttons. 2. Restart the system. 3. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Check mounting position of the magnet and
speed sensor. 2. Start calibration via display gear menu (follow
instructions). 3. Restart the system. 4. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Check light cables and lights for short circuit;
check installed lamps for compatibility with the bike and replace them if necessary. 3. If the problem persists, please contact your specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your specialist dealer. 1. Switch the system off. 2. Allow the motor to cool down and, if necessary, clean the motor’s ventilation vents. 3. Switch on the system. 4. If the problem persists, please contact your specialist dealer. 1. Restart the system. 2. Check mounting position of the magnet and speed sensor. 3. If the problem persists, please contact your specialist dealer. 1. Restart the system with no pressure on the pedals. 2. If the problem persists, please contact your specialist dealer.
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
30
INSTRUCTION MANUAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
Error code 4D-03
Error description
Gear error Release pedals
4D-08
Gear error Stop, release pedals
4D-11 4D-xx
Gear error Shifting blocked for 1 min
Gear error
4E-xx
Motor cadence sensor error
4F-xx
Motor authentication error
51-01, 51-02
Motor voltage error E-bike battery voltage error
52-xx
Motor angle sensor error
53-xx
Motor software error
Action/Restriction
1. Release pedals so that wheel can shift into the required speed for the pushing aid, wait 3 seconds.
2. Restart the system with no pressure on the pedals.
3. Start calibration via display gear menu (follow instructions).
4. If the problem persists, please contact your specialist dealer.
1. Stop the bike, release the pedals, wait 3 seconds. 2. Restart the system with no pressure on the
pedals. 3. Start calibration via display gear menu (follow
instructions). 4. If the problem persists, please contact your
specialist dealer. 1. Wait 1 minute. 2. Restart the system. 3. Start calibration via display gear menu (follow
instructions). 4. If the problem persists, please contact your
specialist dealer. 1. Release pedals, wait 3 seconds. 2. Restart the system with no pressure on the
pedals. 3. Start calibration via display gear menu (follow
instructions). 4. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Check lights and associated cables for damage. 3. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer.
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
31
INSTRUCTION MANUAL 67-xx up to 85-xx and FF-xx
Error code
67-01, 67-03, 67-06, 67-12
67-02, 67-07, 67-08, 67-09, 67-13
67-05, 67-0A, 67-0B, 67-11, 67-15
68-01, 68-05, 68-06, 68-07, 68-09, 68-16, 68-17, 68-18, 68-19, 68-1A
68-02, 68-03, 68-08, 68-0A
Error description Battery voltage error Battery voltage error
Battery voltage error
Battery current error Discharging error
Battery current error Charging error
68-04, 68-11, 68-12
Battery current error Short circuit
68-0B, 68-13
Battery current error Overcurrent error
68-14
Battery current error Start error
68-15
Battery current error
69-01, 69-08
Battery temperature error
69-02, 69-09
Battery temperature error
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
Action/Restriction
1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Connect the battery to the charger. 2. Restart the system. 3. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer.
1. Switch the system off. 2. Remove the battery. 3. Re-insert battery. 4. Start the system. 5. If the problem persists, please contact your
specialist dealer. 1. Disconnect the charger from the battery. 2. Reconnect the charger and start charging. 3. If the problem persists, please contact your
specialist dealer. 1. Switch the system off. 2. Remove the battery. 3. Re-insert battery. 4. Start the system. 5. If the problem persists, please contact your
specialist dealer. 1. Switch the system off. 2. Remove the battery. 3. Re-insert battery. 4. Start the system. 5. If the problem persists, please contact your
specialist dealer. 1. Switch the system off. 2. Remove the battery. 3. Re-insert battery. 4. Start the system. 5. If the problem persists, please contact your
specialist dealer. 1. Switch the system off. 2. Remove the battery. 3. Re-insert battery. 4. Start the system. 5. If the problem persists, please contact your
specialist dealer. 1. Disconnect the charger from the battery. 2. Allow the battery to cool down (> 60 minutes). 3. Restart the charging process. 4. If the problem persists, please contact your
specialist dealer. 1. Turn off the e-bike. 2. Allow the battery to cool down (> 60 minutes). 3. Start the system. 4. If the problem persists, please contact your
specialist dealer.
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
32
INSTRUCTION MANUAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
Error code 69-03, 69-0C
Error description Battery temperature error
69-04, 69-0D
Battery temperature error
69-05, 69-0A, 69-0F, 69-11, 69-12
Battery temperature error
69-06, 69-0B, 69-10
Battery temperature error
69-13 6A-xx
Battery temperature error Battery software error
6B-xx 6C-xx
Battery hardware error Battery communication error
6D-xx
Battery authentication error
6E-xx
Battery unknown error
Action/Restriction
1. Bring the battery to a warmer place. 2. Allow the battery to warm up (> 30 minutes). 3. Restart the charging process. 4. If the problem persists, please contact your
specialist dealer. 1. System operating below the permissible
temperature. 2. Allow the battery to warm up in a warm
environment (> 30 minutes). 3. Start the system. 4. If the problem persists, please contact your
specialist dealer. 1. Turn off the e-bike. 2. Allow the battery to cool down ((> 60 minutes). 3. Start the system. 4. If the problem persists, please contact your
specialist dealer. 1. System operating below the permissible
temperature. 2. Allow the battery to warm up in a warm
environment (> 30 minutes). 3. Start the system. 4. If the problem persists, please contact your
specialist dealer. 1. Start the system. 2. If the problem persists, please contact your
specialist dealer. 1. Check whether the correct battery is installed
(36V/48V). 2. Check the plug contacts on the battery and
bicycle and clean if necessary. 3. Restart the system. 4. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Check whether the correct battery is installed
(36V/48V). 2. Check the plug contacts on the battery and
bicycle and clean if necessary. 3. Restart the system. 4. If the problem persists, please contact your
specialist dealer. 1. Check whether the correct battery is installed
(36V/48V). 2. Check the plug contacts on the battery and
bicycle and clean if necessary. 3. Restart the system. 4. If the problem persists, please contact your
specialist dealer. 1. Check whether the correct battery is installed
(36V/48V). 2. Check the plug contacts on the battery and
bicycle and clean if necessary. 3. Restart the system. 4. If the problem persists, please contact your
specialist dealer.
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
33
INSTRUCTION MANUAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
Error code FF-xx
Error description Battery start error
86-xx up to 8A-xx
Action/Restriction
1. Restart the system. 2. If the problem persists, please contact your
specialist dealer.
Error code 86-xx
87-xx
Error description Speed node software error
Speed node authentication error
Action/Restriction
1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer.
95-xx up to 99-xx
Error code 95-xx
Error description Charger software error
96-xx
Charger voltage error
97-xx
Charger current error
98-xx
Charger temperature error
8B-xx up to 92-xx
Action/Restriction
1. Check whether the correct battery is installed (36V/48V).
2. Disconnect the charger from the system and socket.
3. Wait until status LED goes out. 4. Reconnect the charger to the socket. 5. Reconnect the charger to the system. 6. If the problem persists, please contact your
specialist dealer. 1. Check whether the correct battery is installed
(36V/48V). 2. Disconnect the charger from the system and
socket. 3. Wait until status LED goes out. 4. Reconnect the charger to the socket. 5. Reconnect the charger to the system. 6. If the problem persists, please contact your
specialist dealer. 1. Check whether the correct battery is installed
(36V/48V). 2. Disconnect the charger from the system and
socket. 3. Wait until status LED goes out. 4. Reconnect the charger to the socket. 5. Reconnect the charger to the system. 6. If the problem persists, please contact your
specialist dealer. 1. Disconnect the charger from the battery. 2. Allow the charger to cool (> 30 minutes). 3. Restart the charging process. 4. If the problem persists, please contact your
specialist dealer.
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
34
INSTRUCTION MANUAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
Error code 8B-xx 8C-06
8C-xx
Error description Gears authentication error
Gears hardware error Calibration required
Gears hardware error
9A-xx up to 9E-xx
Error code 9A-xx
Error description Lock authentication error
9B-xx
Lock blocked
9C-xx
Lock hardware error
9D-xx
Lock movement detected
Action/Restriction
1. Restart the system. 2. If the problem persists, please contact your
specialist dealer. 1. Calibrate the gears as described in the
corresponding operating instructions. 2. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. If the problem persists, please contact your
specialist dealer.
Action/Restriction
1. Check whether an original FIT lock is installed. 2. Restart the system. 3. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Check lock for contamination. 3. If the problem persists, please contact your
specialist dealer. 1. Restart the system. 2. Check lock for damage. 3. If the problem persists, please contact your
specialist dealer. 1. Resend lock command 2. Restart the system. 3. Check lock for damage. 4. If the problem persists, please contact your
specialist dealer.
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
35
INSTRUCTION MANUAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
7 CLEANING AND SERVICING
7.1 BASIC CLEANING
7.1.1 CLEAN FIT MASTER NODE BASIC AND FIT REMOTE PURE LEFT
INFO-CIR
Note If water enters the FIT Master Node Basic or the FIT Remote Pure Left, they will be destroyed.
Never immerse the FIT Master Node Basic or the FIT Remote Pure Left in water. Never clean with a high-pressure cleaner, water jet or compressed air. Never use cleaning agents. Clean the FIT Master Node Basic and FIT Remote Pure Left carefully with a damp, soft cloth.
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
36
INSTRUCTION MANUAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
8 TROUBLESHOOTING, FAULT CLEARANCE AND REPAIR
8.1 TESTING AND TROUBLESHOOTING
8.1.1 THE DRIVE SYSTEM OR FIT MASTER NODE BASIC DO NOT START
If the display and/or drive system do not start, proceed as follows:
1. Check if the battery is inserted correctly. If not, insert the battery correctly. 2. Start the drive system. 3. If the drive system does not start, remove the battery, check the charging status and charge if necessary. 4. Clean all contacts with a soft cloth. 5. Insert the battery. 6. Start the drive system. 7. If the drive system does not start, contact the specialist dealer.
INFO-CIR
NOTICE If the battery terminal contacts are heavily soiled/oxidized, take your e-bike to the specialist dealer for a detailed check.
8.1.2 UNUSUAL DISPLAY WHEN STARTING UP
If the upper and lower LEDs flash alternately in green and red when starting up, the e-bike is in «OEM”, «Test» or «Not for Sale» mode. Please contact your specialist dealer to set the e-bike to the correct mode.
8.1.3 ERROR IN ASSISTANCE
Symptom
No assistance is provided.
Cause/Possibility
Is the speed too high?
Is the battery sufficiently charged? Driving at high temperatures, on long inclines or for a long time with heavy loads may cause the motor to overheat. The battery, the FIT Master Node Basic or the FIT Remote Pure Left may be incorrectly connected or there may be a problem with one or more of them.
Remedy
1. Motor assistance is only active up to the
maximum speed for which the e-bike is
approved.
You can display the current speed with the
2. 34.. 5.
boCCITWfuapohtarttnehniticttoeerkonarobyfablwfa.laattFhtpthteIipelTeer.rydDyarirnsicivvdhaeealcmsrShgyceosercst.eketemeanmg.ianpinttyh. ,ereFcIThaEr-gBeiktehe
6. Contact the specialist dealer.
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
37
INSTRUCTION MANUAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
Symptom
Cause/Possibility
Remedy
No assistance is provided.
The assisted journey distance is too short.
Pedaling has become difficult.
Are you pedaling?
1. The e-bike is not a motorcycle. Start pedaling.
Is the system switched on?
Is the assistance level set to OFF (Off)?
The battery properties deteriorate in winter weather.
2. Press on/off/light button (control element) to 3. tSuertnththeeassyssistteamncoenl.evel to FLY, FLEX, FLOW or
ECO. 4. If you still feel that no assistance is being Thipsrdooveidsendo, tcoinndtiaccatteyoauprrsopbelecmial.ist dealer.
The journey distance may be shorter depending on road conditions, the assistance level and the lights’ total operating time.
Is the battery fully charged?
The battery is a wearing part. Repeated charging and long periods of use lead to a drop in the battery performance (power loss).
Are the tires pumped up to sufficient pressure?
Is the assistance level set to OFF (Off)?
Battery charge may be low.
Was the system switched on with a foot on the pedal?
1. Check battery charge. 2. If the battery is almost empty, recharge the
battery.
3. If the total distance that can be covered with a fully charged battery has become shorter, the battery may be impacted. Replace the battery
4. wIf itthheadnisetwanocneet.hat can be driven with a single charge is very short, replace the battery with a new one.
1. Pump up the tires.
2. Set the assistance level to FLY, FLEX, FLOW or ECO.
3. Check battery charge. 45.. bpISfaewttdhittaeeclrshby.a.thtteersyysisteamlmoonstagemainptWy,itrhecohuatrpgreesthseing the 6. If assistance is still not provided, contact your
specialist dealer.
8.2 REPAIR
Special expertise and tools are required for many repairs. That is why only a specialist dealer may perform repairs.
8.2.1 ORIGINAL PART
The individual e-bike parts have been carefully selected and matched to one other. Only original parts must be used for maintenance and repair. Observe the operating instructions for the new components.
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
38
INSTRUCTION MANUAL
9 RECYCLING AND DISPOSAL
9.1 DISPOSAL
FIT MASTER NODE BASIC + FIT REMOTE PURE LEFT PINION
Mechanical and electrical equipment, accessories and packaging should be recycled in an environmentally sound manner. Don’t throw them in the garbage!
Only for EU countries: According to European Directives 2012/19/EU, 2006/66/EC and their transposition into national law, defective or unusable waste electrical and electronic equipment, rechargeable batteries and batteries must be collected separately and recycled in an environmentally sound manner.
FIT_Manual_Master_Node_Basic_Remote_Pure_Left_Pinion_V5_en.pdf | Version 05 | 06.06.2025
39
Documents / Resources
 | 501301,501303 Master Node Basic Plus |
References
- Auto.Shift.Proauto.shift.pro
- ebike.chfit-ebike.comebike.chfit-ebike.com
- FIT E-Bike System Integration | Smartscale NewCo Europe GmbHfit-ebike.com
- Our declarations of conformity - information & download | Smartscale NewCo Europe GmbHfit-ebike.com
- FIT E-Bike System Integration | Smartscale NewCo Europe GmbHfit-ebike.com
- Our declarations of conformity - information & download | Smartscale NewCo Europe GmbHfit-ebike.com
- User Manualmanual.tools