FTI-CDP1 Remote Start T-Harness
“
Specifications:
- Make: DL-CH8 RAM
- Model: 2500 TIP Start (Gas)
- Year: 2018
- Install Type: 2 CAN CJB
- Lights: Park / Auto Type B IGN BCM
Product Usage Instructions:
Module Programming Procedure:
- Close the driver door.
- Turn the key to the OFF position.
- Re-open the driver door to wake up the data bus.
- Press UNLOCK on the OEM remote or press the module programming
button. - Wait for the LED to flash BLUE once [1x].
- Turn the key to the ON position.
- Wait for the LED to turn solid RED.
- Turn the key to the OFF position, remove the key, and then
insert it into the ignition. - Turn the key to the ON position and wait for the LED to flash
BLUE. - Disconnect power last and connect RS to the computer for
extended programming.
Take Over Procedure:
- Press UNLOCK on the aftermarket remote.
- Within 45 seconds from the previous step: Open vehicle door,
enter vehicle, close vehicle door, insert key into ignition, turn
key to ON position, and press and release BRAKE pedal. - Failure to follow the procedure within the time restriction
will result in vehicle engine shutdown.
FAQ:
Q: What should I do if the remote starter malfunctions?
A: Ensure all vehicle doors are closed and locked prior to the
remote start sequence. If an issue persists, consult the product
manual or contact customer support.
Q: How can I prevent vehicle engine shutdown during the
take-over procedure?
A: Follow the take-over procedure promptly within the specified
time restriction to avoid engine shutdown.
“`
FTI-CDP1 – Notas de preparación y cobertura del vehículo
Make
DL-CH8 RAM
Model 2500 TIP Start (Gas)
Year 2018
Install Type 2
CAN CJB
Lights
Park / Auto
Type B
IGN BCM
Hood I/O Changes
BCM
Green White/Blue
Firmware: Los vehículos cubiertos usan BLADE-AL (DL) -CH8, confirman la aplicación, el módulo flash y actualizan el controlador firmware antes de instalar.
CAN: Los vehículos tipo 1 usan conexiones CAN en el arnés en OBD-II, la extensión CAN incluida no es necesaria para este tipo de instalación.
Luces: Las luces de estacionamiento tipo B usan el conector de 10 pines, asegúrese de que el conector de 6 pines no utilizado esté debidamente asegurado por seguridad.
Iignición: Las disposiciones comunes de encendido se enumeran en el diagrama de la HOJA, el encendido también está disponible en el vehículo BCM (conector C5 / E, rosa / blanco, pin # 27).
FTI-CDP1 – Notas de instalación y configuración
A Conexiones CAN necesarias. B No se requiere conexión. C Conexión de pasador de capó (si es necesario). D Puente de ignición, CNONSEECRTEAQRSUEIEAREROCSOAN.EXIÓN. E Conexión de ignición.
IIIIIIIIIIIIIIIIIIIIIIEIIIRIIIIIIIIIIIIIIIIIIIIIIIIIIIII
D LAN
2001
O
O
Z
K E R E D
st. E
IIIIIIIII
S
ID
D
KO O
rG
fo AD E
R R
E ‘T T AN NC
CE AND
WHO
O H W
WANNA
LEARN
TO
IIIIIIIII
BLADE FEATURE COVERAGE
CM7000/7200 Cut loop for A/T
CM7X00
CM-900S/900AS
CM900AS/900S Jumper
IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII D
O OTHER STUFF GOOD TOO
IMMOBILIZER DATA PRIORITY UNLOCK DOOR LOCK DOOR UNLOCK ARM OEM ALARM DISARM OEM ALARM DOOR STATUS RAP SHUTDOWN BRAKE STATUS E-BRAKE STATUS TACH OUTPUT GLOW PLUG STATUS SECURE TAKEOVER PARKING LIGHTS
CM -900
FTI-CDP1 – DL-CH8 – Type 2 2018 RAM 2500 TIP Start (Gas)
BLADE
PWR
pink/black
HOOD
C
D
green pink
A
B
B
3 4 1
Firstech Techfeedtree
2
OBD-II connector 1
1
16
TIP Start Cylinder
ACC RUN S
2
TART
OF F
Type B
Headlight switch
3
AUTO
*Not required
BCM 4
RAP SHUTDOWN
Green
5
Junction Block
HL
C5 – Ignition
Driver side dash
A
or
48
39 27 26 25
brown
10
1
E
yellow
pink/white
C
INSTALL AFTERMARKET PART IF REQUIRED
Códigos de error de programación de LED
El LED del módulo parpadea en ROJO durante la programación 1x – Error CAN, verifique el cableado y los voltajes CAN 2x – Código clave no aprendido, verifique CAN 3x – No hay datos del inmovilizador, verifique la conexión immo 4x – Sin IGN, verifique la conexión IGN 5x – VIN no encontrado, verifique las conexiones CAN 6x – No hay datos del inmovilizador, verifique la conexión immo 7x – No es la misma clave, use solo una clave para programar 8x – No hay datos del inmovilizador, verifique la conexión immo 9x – Sin datos del inmovilizador 10x – Error de Klon, rehacer Klon
INSTALL GUIDE
Patent No. US 8,856,780 CA 2759622
ALL IN ONE
DODGE/RAM
COM-BLADE-AL(DL)-CH8-EN
Doc. No.: ##65995## 20191004
MODULE PROGRAMMING PROCEDURE – WITH KLON
1
Close driver door.
11
OFF
Turn key to OFF position.
2
3 4 5 6 7 8 9 10
Re-open driver door to wake up data bus.
Press UNLOCK on OEM remote. If the vehicle is not equipped with an OEM remote, press the module programming button.
Wait, LED will flash BLUE once [1x].
Turn key to ON position.
ON
Wait, LED will turn solid RED.
OFF
Turn key to OFF position.
Remove key.
Insert key into ignition.
Turn key to ON position. ON
Wait, LED will flash BLUE.
12 13
WARNING: Disconnect power last. Disconnect RS from vehicle.
Connect RS to computer and proceed with extended programming.
14
WARNING: Do not press RS programming button. Connect power first. Connect RS to vehicle.
15 16 17
Turn key to ON position.
ON
Wait, LED will turn solid BLUE for 2 seconds.
OFF
Turn key to OFF position.
18 19
START
Turn key to START position.
OFF
Turn key to OFF position.
20
Module Programming Procedure completed.
WWW.IDATALINK.COM
Automotive Data Solutions Inc. © 2020
INSTALL GUIDE
Patent No. US 8,856,780 CA 2759622
ALL IN ONE
DODGE/RAM
COM-BLADE-AL(DL)-CH8-EN
Doc. No.: ##65995## 20191004
WARNING: READ BEFORE RNEOMTOICTEE STARTING THE VEHICLE
IMPORTANT
I All vehicle doors must be closed and locked prior to remote start sequence. Failure to comply will result in remote starter malfunction.
TAKE OVER PROCEDURE – TO THE VEHICLE OWNER
NOTE
2
I All vehicle doors must be closed and locked prior to remote start sequence.
TIME RESTRICTI N COMING UP !
1
Press UNLOCK on after-market
remote.
3
TIME RESTRICTI N
Within 45 SECONDSfrom previous step:
Open vehicle door. Enter vehicle. Close vehicle door. Insert key into ignition. Turn key to ON position. Press and release BRAKE pedal.
Take over procedure completed.
!
Failure to follow procedure within time restriction will result in vehicle engine shutdown.
WWW.IDATALINK.COM
Automotive Data Solutions Inc. © 2020
Documents / Resources
 |
FIRSTTECH FTI-CDP1 Remote Start T-Harness [pdf] Installation Guide DL-CH8, CM7000-7200, CM-900S-900AS, FTI-CDP1 Remote Start T-Harness, FTI-CDP1, Remote Start T-Harness, Start T-Harness, T-Harness |
