SUPPORT-1(888) 820-3690, EXT. 203
FTI-STK1 Ascent STD KEY AT
FTI-STK1: Vehicle Coverage and Preparation Notes
| Make | Model | Year | Install | CAN | IMMO | BCM | Clutch | I/O Changes |
| DL-SUB9 | Type | Green White/Blue | ||||||
| Subaru | Ascent STD KEY AT (USA) | 2019-22 | Type 4 | 40-Pin | A | DSD | N/A | N/A |
Covered vehicle use BLADE-AL-SUB9 firmware and the following required accessories, Weblink Hub & ACC RFID1.
Flash module, and update the controller firmware. Please follow the directions for RFID programming before attempting to program the BLADE module to the vehicle.
CAN: Type 4 CAN connections are made using the 40-Pin BCM connector and require connecting the white 2-pin female connector to the black male 2-pin connector at marker [D] of the illustration.
Immobilizer: Type A IMMO requires connecting the white male and female 2-pin connectors at marker [C] of the illustration.
Lights: Parking lights are pre-wired in the FTI-STK1 harness. Replace the green/white wire of the CM I/O connector with the pre-terminated green/white wire of the harness.
ACC-RFID1 (REQUIRED): SUB9 firmware does not provide immobilizer data, an ACC-RFID1 is therefore required for remote start
2nd START: The FTI-STK1 harness is pre-wired with a red/white 2nd START output (not required in TYPE 2), cut and insulate the provided wire to prevent short circuits when not used.
I/O Changes: None required
Advisory 1: Program ACC-RFID1 before attempting to program the BLADE module to the vehicle.
Advisory 2: Secure all 2-pin connections, both used and unused, to the main harness body.
FTI-STK1: Installation and Configuration Notes
A………..REQUIRED ACCESSORY
B…………..ADAPTER NOT REQUIRED
C……………. REQUIRED CONFIGURATION (TYPE A IMMO)
D……………. REQUIRED CONNECTION
E………….. NO CONNECTION
FEATURE COVERAGE
| IMMOBILIZER DATA |  |
| ARM OEM ALARM | |
| DISARM OEM ALARM | |
| DOOR LOCK | |
| DOOR UNLOCK | |
| PRIORITY UNLOCK | |
| TRUNK/HATCH RELEASE | |
| TACH OUTPUT | |
| DOOR STATUS | |
| TRUNK STATUS | |
| BRAKE STATUS | |
| E-BRAKE STATUS | |
| A/M ALRM CONTROL FROM OEM REMOTE | |
| A/M RS CONTROL FROM OEM REMOTE | |
| AUTOLIGHT CTRL | |
FT-DAS Required for manual transmission.
BOTH Red & Red/White MUST be connected with high current application.
CM900AS/900S Jumper
FTI-STK1 – AL-SUB9 – Type 4
2019-22 Subaru Ascent STD KEY AT (USA)
LED Programming Error Codes
Module LED flashing RED during programming
1x RED = Unable to communicate with RFID or immobilizer data.
2x RED = No CAN activity. Check the CAN wire connections.
3x RED = No ignition detected. Check the ignition wire connection and CAN.
4x RED = Required ignition output diode not detected.
INSTALL GUIDE
SUBARU ALL IN ONE
COM-BLADE-AL(AL)-SUB9-EN
Doc. No.: ##82344##
CARTRIDGE INSTALLATION
- Slide cartridge into unit. Notice button under LED.
Ready for Module Programming Procedure.
MODULE PROGRAMMING PROCEDURE
- For this installation, the Weblink HUB is required.
- Remove OEM key 1 from keychain.
Place all other keyfobs at least 1 foot away from the Weblink HUB. Failure to comply may result in damage to other keyfobs or interfere with the keyfob reading process.
- Flash the module using the Weblink HUB. Follow the on screen instructions to complete the keyfob reading process.
- WARNING:
Do not press the module programming button.
Connect power first. Connect module to vehicle.
- Using OEM key 1, turn key to ON position.
- Wait, LED will turn solid BLUE for 2 seconds..
- Turn key to OFF position. Module Programming Procedure completed.
WWW.IDATALINK.COM
Automotive Data Solutions Inc. © 2020
Documents / Resources
 | FIRSTECH FTI-STK1 Ascent STD KEY AT [pdf] Installation Guide FTI-STK1 Ascent STD KEY AT, FTI-STK1, Ascent STD KEY AT, STD KEY AT, KEY AT, AT |