Firecell logoFirecell FCX 170-001 Wireless Detector - logoWireless Call Point (KAC Front)
Installation GuideFirecell FC 200 002 Wireless Call Point -

Part no Product Description
FC-200-002 Wireless Call Point (KAC Front)
5-5201/EN54 Replacement Element

Pre-installation

westermo Viper 8 Series EN 50155 Managed Gigabit Routing Switch - WARNING Installation must conform to applicable local installation codes and should only be installed by a fully trained competent person.

  • Ensure that the device is installed as per the site survey.
  • The use of a non-metallic spacer should be considered if mounting the device onto a metal surface.
  • Do NOT Press the Log On button on a pre-programmed device, as this will cause communication with the Control Panel to be lost. Should this happen, delete the device from the system and add it back on.
  • This device contains electronics that may be susceptible to damage from Electrostatic Discharge (ESD). Take appropriate precautions when handling electronic boards.

Components

Firecell FC 200 002 Wireless Call Point - Components

  1. Protective cover
  2. Fixing screw
  3. Wireless call point
  4. Mounting plate

Fix mounting plate

  • Remove the mounting plate from the wireless call point. See Step 5 for more information on unlocking the device.
  • Ensure the mounting plate is fitted in the orientation shown.
  • Use both mounting holes.
  • Use suitable fasteners and fixings.

Firecell FC 200 002 Wireless Call Point - Fix mounting plate

Power device

  • When fitting / replacing batteries; observe correct polarity, using only specified batteries.
  • Connect the power jumper across the PIN header.
  • Once powered, reassemble the device.

Firecell FC 200 002 Wireless Call Point - Power device

Device locking

To open the call point, loosen the fixing screw, then slide the call point up, away from the mounting plate.
When reassembling, observe the hinged connection located on the device’s top edge first, prior to closing the unit.
Finally, lock the call point into the mounting plate by tightening the fixing screw.

Firecell FC 200 002 Wireless Call Point - Device locking

Configuration

The device’s loop address is configured within the user interface’s menu structure.

  • Refer to the programming manual for full programming details.

Firecell FC 200 002 Wireless Call Point - 1

FireCell = MK98
Fusion = TSD062
WSM = TSD143
Free to download from www.emsgroup.co.uk

Testing and resetting

Firecell FC 200 002 Wireless Call Point - Testing and resetting

Replacing elements

Firecell FC 200 002 Wireless Call Point - Replacing elements

Specification

Operating temperature -10 to +55 °C
Storage temperature 5 to 30 °C
Humidity 0 to 95% non-condensing
Supply 6x AA alkaline (Panasonic LR6AD Powerline /Varta 4006 Industrial)

CAUTION!
The fitting of an incorrect battery type invalidates the product certification and may result in poor performance.

IP rating IP24
Operating frequency 868 MHz
Output transmitter power Auto-adjusting 0 to 14 dBm (0 to 25 mW)
Dimensions (W x H x D) 89 x 92 x 70 mm
Weight  0.40 kg
Location Type A: For indoor use

Regulatory information

Manufacturer Carrier Manufacturing Polska Sp. Z o.o. Ul. Kolejowa 24. 39-100 Ropczyce, Poland
Year of manufacture See device serial number label
Certification CE SYMBOL 10
Certification
body
905
CPR DoP 0359-CPR-0038
Approved to EN54-11:2001. Incorporating Amendment No. 1 and Corrigendum No. 1. Fire detection and fire alarm
systems. Part 11: Manual call points.
EN54-25:2008. Incorporating corrigenda September 2010 and March 2012. Fire detection and fire alarm
systems. Part 25: Components using radio links.
European Union
directives
EMS declares that this device is in compliance with Directive 2014/53/EU. The full text of the EU
declaration of conformity is available at the following internet address: www.emsgroup.co.uk
Dustbin Icon 2012/19/EU (WEEE directive):
Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see www.recyclethis.info
Dispose of your batteries in an environmentally friendly manner according to your local regulations.

©2021 EMS Ltd. All rights reserved

Documents / Resources

Firecell FC-200-002 Wireless Call Point [pdf] Installation Guide
FC-200-002 Wireless Call Point, FC-200-002, Wireless Call Point

References

Leave a comment

Your email address will not be published. Required fields are marked *