Secure another bracket to the control head/bracket assembly
with 1/4-20 by 3/4-inch hex head screws and 1/4-inch lock
washers.
Mark drill positions using the mounting bracket as a
template.

Drill two pilot mounting holes at the marked positions.
Secure the mounting bracket to the surface using #10
thread-forming screws.

FAQ (Frequently Asked Questions)

Q: What should I do before installation?

A: Ensure you have knowledge of vehicle systems and safety
warning equipment installation practices. Refer to the vehicle’s
service manuals for guidance.

Q: What connections are required for the control head?

A: The control head requires connections to a 25-foot
Convergence Network cable and the Federal Signal Microphone (P/N
258B8577-03).

“`

View Fullscreen

25500978 Rev. A0 0225

Pathfinder 17-Button with Rotary Knob Remote, PF200S17BRK and PF400S17BRK – Supplement

Safety Message to Installers of Sound/Light Equipment

People’s lives depend on your proper installation and servicing of Federal Signal products. It is important to read and follow all instructions shipped with this product. Listed below are some other important safety instructions and precautions you should follow.
Before Installation
Qualifications · To properly install an electronic siren, you must have a good understanding of automotive electrical
procedures and systems, along with proficiency in the installation and service of safety warning equipment. Always refer to the vehicle’s service manuals when performing equipment installations on a vehicle.
Sound Hazards · Your hearing and the hearing of others in or close to your emergency vehicle could be damaged by
loud sounds. This can occur from short exposures to very loud sounds, or from longer exposures to moderately loud sounds. For hearing conservation guidance, refer to federal, state, or local recommendations. OSHA Standard 1910.95 offers guidance on “Permissible Noise Exposure.”
· All effective sirens and horns produce loud sounds (120 dB) that may cause permanent hearing loss. Always minimize your exposure to siren sounds and wear hearing protection. Do not sound the siren indoors or in enclosed areas where you and others will be exposed to the sound.
· Federal Signal siren amplifier/relay modules and speakers are designed to work together as a system. Combining a siren and speaker from different manufacturers may reduce the warning effectiveness of the siren system and may damage the components. Verify or test your combination to make sure the system works together properly and meets federal, state, and local standards or guidelines.
During Installation
· Do NOT get metal shavings inside the product. Metal shavings in the product can cause the system to fail. If drilling must be done near the unit, place an ESD-approved cover over the unit to prevent metal shavings from entering the unit. Inspect the unit after mounting to ensure that there are no shavings present in or near the unit.
· Do NOT connect this system to the vehicle battery until ALL other electrical connections are made, mounting of all components is complete, and you have verified that no shorts exist. If wiring is shorted to vehicle frame, high current conductors can cause hazardous sparks, resulting in electrical fires or flying molten metal.
· Ensure that the siren amplifier/relay module and speaker(s) in your installation have compatible wattage ratings.
· In order for the electronic siren to function properly, the ground connection must be made to the NEGATIVE battery terminal.
· Sound output will be severely reduced if any objects are in front of the speaker. If maximum sound output is required for your application, ensure that the front of the speaker is clear of any obstructions.

Pathfinder® 17-Button with Rotary Knob Remote
· Install the speaker(s) as far forward on the vehicle as possible in a location that provides maximum signaling effectiveness and minimizes the sound reaching the vehicle’s occupants. Refer to the National Institute of Justice guide 500-00 for further information.
· Mounting the speakers behind the grille will reduce the sound output and warning effectiveness of the siren system. Before mounting speakers behind the grille, make sure the vehicle operators are trained and understand that this type of installation is less effective for warning others.
· Sound propagation and warning effectiveness will be severely reduced if the speaker is not facing forward. Carefully follow the installation instructions and always install the speaker with the projector facing forward.
· Do NOT install the speaker(s) or route the speaker wires where they may interfere with the operation of airbag sensors.
· Do NOT install equipment or route wiring or cord in the deployment path of an airbag.
· If a vehicle seat is temporarily removed, verify with the vehicle’s manufacturer if the seat needs to be recalibrated for proper airbag deployment.
· Installation of two speakers requires wiring speakers in phase.
· Never attempt to install aftermarket equipment that connects to the vehicle wiring without reviewing a vehicle wiring diagram available from the vehicle’s manufacturer. Ensure that your installation will not affect vehicle operation and safety functions or circuits. Always check vehicle for proper operation after installation.
· Locate the handheld so the vehicle, controls, and microphone can be operated safely.
· When drilling into a vehicle structure, ensure that both sides of the surface are clear of anything that could be damaged. All drilled holes should be deburred, and all sharp edges should be smoothed. All wires going through drilled holes should be protected by a grommet or convolute/split-loom tubing. All exterior drilled holes must be sealed with Motorcraft® seam sealer T-A-2-B or equivalent to prevent the potential exposure to carbon monoxide or other potentially harmful fumes. Failure to observe this warning could cause serious injury or death.
After Installation · After installation, test the siren and light system to ensure that it is operating properly.
· Test all vehicle functions, including horn operation, vehicle safety functions, and vehicle light systems, to ensure proper operation. Ensure that installation has not affected vehicle operation or changed any vehicle safety function or circuit.
· After testing is complete, provide a copy of these instructions to the instructional staff and all operating personnel.
· File these instructions in a safe place and refer to them when maintaining or reinstalling the product.
Failure to follow all safety precautions and instructions may result in property damage, serious injury, or death.
RETAIN AND REFER TO THESE MESSAGES

Models PF200S17BRK and PF400S17BRK

Federal Signal www.fedsig.com

Pathfinder® 17-Button with Rotary Knob Remote

Introduction
This publication has instructions for installing the Pathfinder® with the 17-button with rotary knob control head. Select a mounting location that allows the vehicle, controls, and microphone to be operated safely under all driving conditions. To identify safe mounting areas for equipment inside the vehicle, consult the vehicle manufacturer’s guidelines. To avoid driver distraction and unreliable switch activation, the mounting location must not allow any movement of the unit. Installer-supplied mounting hardware is required to mount the siren.

NOTE: For additional electrical installation instructions, refer to the Installation and Maintenance Instructions packed with the Pathfinder.

Unpacking the Kit
After unpacking the kit, inspect it for damage that may have occurred in transit. If it has been damaged, do not attempt to install or operate it. File a claim immediately with the carrier, stating the extent of the damage. Carefully check all envelopes, shipping labels, and tags before removing or destroying them. Ensure that the parts in Table 1 or Table 2 are included in the package. If you are missing any parts, contact Customer Support at 1-800-264-3578, 7 a.m. to 5 p.m., Monday through Friday (CT).

Table 1 PF200S17BRK kit contents

Qty. Description 1 Pathfinder 100/200-Watt Amplifier 1 PF200S17BRK Remote Control Head 1 Keypad Legend Stickers 1 Dynamic Microphone with Mod 1 Pathfinder Plastic Bail Bracket 2 Smart Control Mtg. Bracket 1 RS485 25-foot (7.62 m) Cable Assembly 1 Pathfinder Relay Wire Assembly 1 Pathfinder I/O Wire Assembly 1 A male to Mini-B USB 2.0 Cable 1 8P8C RJ45 T 1 F to 2 F Adapter Connector 1 RS485 8-inch Cable Assembly 1 Pathfinder Hardware Kit Siren Mount Kit 2 Term, #8, 6 AWG 2 1/4-20 Stainless Steel Carriage Bolt 2 1/4-20 Stl External Tooth Keps® Nut 2 1/4-inch Flat Washer 2 M4 SEMS Pan Head Screw 2 1/4-inch Internal Tooth Lockwasher 1 Pathfinder Control Head Hardware Kit Control Head Kit 2 #6-32 Pan Head Phillips® Screw 2 1/4-20, Stl Zinc Clear Bolt Cap 2 #10 Type B Stl Black Zinc Pan Head Screw 2 Split Stl #6 Screw Lockwasher 2 1/4-inch External Tooth Lockwasher

Part Number 862302662 862304460 8572294 258B577-03 862303559 82361065 1751357-02 17501359 17501360 17501813 13901989 1751357-06 77700765
19001363 7004A020-12 7058A005 7072A028 70000451-06 7075A016 77700992
7000A404-05 7002A000-12 7011246-08 7074A001 7075A007

Models PF200S17BRK and PF400S17BRK

Federal Signal www.fedsig.com

Pathfinder® 17-Button with Rotary Knob Remote
Table 2 PF400S17BRK kit contents
Qty. Description 1 Pathfinder® 400-Watt Amplifier 1 PF400S17BRK Remote Control Head 1 Keypad Legend Stickers 1 Dynamic Microphone with Mod 1 PF400 Mounting Bracket 2 Smart Control Mtg. Bracket 1 RS485 25-foot (7.62 m) Cable Assembly 1 Pathfinder Relay Wire Assembly 1 Pathfinder I/O Wire Assembly 1 PF400 Audio Out Wire Assembly 1 PF400 Mounting Hardware Kit Siren Mount Kit 4 1/4-20 x 5/8-inch Carriage Bolt 4 1/4-20 Elastic Stop Nut 4 1/4-inch Flat Washer 1 Pathfinder Control Head Hardware Kit Control Head Kit 2 #6-32 Pan Head Phillips® Screw 2 1/4-20, Stl Zinc Clear Bolt Cap 2 #10 Type B Stl Black Zinc Pan Head Screw 2 Split Stl #6 Screw Lockwasher 2 1/4-inch External Tooth Lockwasher

Part Number 862303915 862304460 8572294 258B577-03 862304026A 82361065 1751357-02 17501359 17501360 17502532 77701562
7004A020-10 7058A010 7072A024 77700992
7000A404-05 7002A000-12 7011246-08 7074A001 7075A007

Connecting the Control Head The only connections required for the control head are the 25-foot Convergence Network cable and the Federal Signal Microphone (P/N 258B8577-03).

Figure 1 Control Head Connections

Microphone

Convergence Network

USB-C

Models PF200S17BRK and PF400S17BRK

Federal Signal www.fedsig.com

Pathfinder® 17-Button with Rotary Knob Remote
Mounting the Control Head The control head comes with two mounting brackets and mounting hardware. Tools needed: · Drill with 11/64-inch drill bit · Phillips® screwdriver · 7/16-inch nut driver · Pencil or felt-tip pen for marking drill position locations
AIRBAG DEPLOYMENT: Do not install equipment or route wiring in the deployment of an airbag. Failure to observe this warning will reduce the effectiveness of the airbag or potentially dislodge the equipment, causing serious injury or death. To mount the control head: 1. Secure a bracket to the control head with the #6-32 by 1/4-inch Phillips screws and #6 lock washers.
See Figure 2.
Figure 2 Bracket attached to back of control head

2. Using a 7/16-inch nut driver, secure the other bracket to the control head/bracket assembly with the 1/4-20 by 3/4-inch hex head screws and 1/4-inch lock washers. See Figure 2.
3. Using the mounting bracket as a template, scribe two drill position marks at the selected mounting location.

DRILLING PRECAUTIONS: Before drilling holes, check the area into which you plan to drill to ensure that you do not damage vehicle components while drilling. All drilled holes should be deburred, and all sharp edges should be smoothed. All wires going through drilled holes should be protected by a grommet or convolute/split-loom tubing. All exterior drilled holes must be sealed with Motorcraft® seam sealer T-A-2-B or equivalent to prevent the potential exposure to carbon monoxide or other potentially harmful fumes. Failure to observe this warning could cause serious injury or death.

Models PF200S17BRK and PF400S17BRK

Federal Signal www.fedsig.com

Pathfinder® 17-Button with Rotary Knob Remote
4. Drill two pilot mounting holes at the drill position marks. 5. Secure the mounting bracket to the mounting surface with the #10 thread-forming screws. See
Figure 3.
Figure 3 Brackets attached to control head and mounting surface

6. To adjust the angle of the control head, loosen the hinge screws, tilt the control head forward or backward, and then securely tighten the screws.
Keypad Default Functions See Figure 4 and Tables 3-7.
Figure 4 Button layout

Models PF200S17BRK and PF400S17BRK

Federal Signal www.fedsig.com

Pathfinder® 17-Button with Rotary Knob Remote

Table 3 PF200 17-Button with Rotary Knob Default Programming

Button
Slide Switch 1 (SS1)
Slide Switch 2 (SS2)
Slide Switch 3 (SS3)
BTN 1 BTN 2 BTN 3 BTN 4 BTN 5
BTN 6
BTN 7 BTN 8 BTN 9 BTN 10 BTN 11 BTN 12 BTN 13 BTN 14 BTN 15 BTN 16 BTN 17 RADIO STANDBY WAIL YELP HF TONE 1 TONE 2

Default Function
· Light bar – Pattern 10, Front Cutoff · ILS – Rear Pattern 10 · CNSM – Rear Pattern 10 · Relays 1 and 2 ON
· Light bar – Pattern 17 · ILS – Front and Rear Pattern 17 · CNSM – Front and Rear Pattern 17 · Horn Ring Transfer Active · Relays 1, 2, 3, and 4 ON
· Light bar – Pattern 27, Flashing Takedowns · ILS – Front and Rear Pattern 27, Flashing Takedowns · CNSM – Front and Rear Pattern 27, Flashing Takedowns · Horn Ring Transfer Active · Relays 1, 2, 3, 4, and 6 ON
SSP Manual Peak n Hold
Pattern 22, Flashing Takedowns/Alleys (LB/ILS/CNSM) 8-second momentary intersection
Rear Cutoff (LB/ILS/CNSM)
Dimming (LB/ILS/CNSM)
Cruise (LB/ILS/CNSM)
· Step 1 – SignalMasterTM Warn 1 (LB/ILS/CNSM) · Step 2 – SignalMaster Warn 2(LB/ILS/CNSM) · Step 3 – SignalMaster Warn 3 (LB/ILS/CNSM) · Step 4 – SignalMaster Warn 4 (LB/ILS/CNSM)
Relay 5 ON (8-second timer)
SSP Air Horn
Left Alley (LB), Relay 7 ON
Left Scene (LB/ILS/CNSM), Relay 7 ON
Takedown (LB/ILS/CNSM), Relays 11 and 12 ON
Front Scene (LB/ILS/CNSM), Relays 11 and 12 ON
Right Scene (LB/ILS/CNSM), Relay 8 ON
Right Alley (LB), Relay 8 ON
SignalMaster Left (LB/ILS/CNSM)
SignalMaster Center-Out (LB/ILS/CNSM)
SignalMaster Right (LB/ILS/CNSM)
Radio Re-Broadcast
No Active Tone
SSP Wail (Slide Switch 3 Dependent)
SSP Yelp (Slide Switch 3 Dependent)
Hands-free horn ring control active (Slide Switch 3 Dependent)
SSP Priority (Slide Switch 3 Dependent)
Dual Tone; SSP Wail & SSP Yelp (Slide Switch 3 Dependent)

Models PF200S17BRK and PF400S17BRK

Federal Signal www.fedsig.com

Pathfinder® 17-Button with Rotary Knob Remote

Table 4 PF200 17-Button with Rotary Knob Input Default Programming

Input Ignition Park
Input 1 Input 2 Input 3 Input 4 Horn Ring

Default Function
System Enable, immediate system shutdown (no delay) ignition OFF
· Siren Mute · Relay 6 OFF · Flashing Takedown Cutoff (LB/ILS/CNSM)
Remote SS1 Activation
Remote SS2 Activation
Remote SS3 Activation
Remote Rumbler® Activation
· When SS2 is Active, SSP Air Horn · When SS3 is Active and PARK is ON, SSP Air Horn · When SS3 and Wail are Active and PARK is OFF, toggles between SSP Yelp and
Wail with Rumbler · When SS3 and Yelp are Active and PARK is OFF, toggles between SSP Priority and
Yelp with Rumbler · When SS3 and Tone 1 are Active and PARK is OFF, SSP Air Horn · When SS3 and Tone 2 are Active and PARK is OFF, SSP Air Horn · When SS3 and HF are Active and PARK is OFF, 4-Step SSP Wail, Yelp, Dual-tone
Wail/Yelp, and Priority with Rumbler

Polarity BAT GND
GND GND GND GND GND

Models PF200S17BRK and PF400S17BRK

Federal Signal www.fedsig.com

Pathfinder® 17-Button with Rotary Knob Remote

Table 5 PF400 17-Button with Rotary Knob Default Programming

Default Function
· Light bar – Pattern 10, Front Cutoff · ILS – Rear Pattern 10 · CNSM – Rear Pattern 10 · Relays 1 and 13 ON
· Light bar – Pattern 17 · ILS – Front and Rear Pattern 17 · CNSM – Front and Rear Pattern 17 · Horn Ring Transfer Active · Relays 1, 2, 3, and 13 ON
· Light bar – Pattern 27, Flashing Takedowns · ILS – Front and Rear Pattern 27, Flashing Takedowns · CNSM – Front and Rear Pattern 27, Flashing Takedowns · Horn Ring Transfer Active · Relays 1, 2, 3, 4, 5, 13, and 14 ON
SSP Manual Peak n Hold
Pattern 22, Flashing Takedowns/Alleys (LB/ILS/CNSM) 8-second momentary intersection
Rear Cutoff (LB/ILS/CNSM)
Dimming (LB/ILS/CNSM)
Cruise (LB/ILS/CNSM)
· Step 1 – SignalMasterTM Warn 1 (LB/ILS/CNSM) · Step 2 – SignalMaster Warn 2(LB/ILS/CNSM) · Step 3 – SignalMaster Warn 3 (LB/ILS/CNSM) · Step 4 – SignalMaster Warn 4 (LB/ILS/CNSM)
Relay 6 ON (8-second timer)
SSP Air Horn
Left Alley (LB), Relay 7 ON
Left Scene (LB/ILS/CNSM), Relay 7 ON
Takedown (LB/ILS/CNSM), Relays 11 and 12 ON
Front Scene (LB/ILS/CNSM), Relays 11 and 12 ON
Right Scene (LB/ILS/CNSM), Relay 8 ON
Right Alley (LB), Relay 8 ON
SignalMaster Left (LB/ILS/CNSM)
SignalMaster Center-Out (LB/ILS/CNSM)
SignalMaster Right (LB/ILS/CNSM)
Radio Re-Broadcast
No Active Tone
SSP Wail (Slide Switch 3 Dependent)
SSP Yelp (Slide Switch 3 Dependent)
Hands-free horn ring control active (Slide Switch 3 Dependent)
SSP Priority (Slide Switch 3 Dependent)
Dual Tone; SSP Wail & SSP Yelp (Slide Switch 3 Dependent)

Models PF200S17BRK and PF400S17BRK

Federal Signal www.fedsig.com

Pathfinder® 17-Button with Rotary Knob Remote

Table 6 PF400 17-Button with Rotary Knob Input Default Programming

Input Ignition Park
Input 1 Input 2 Input 3 Input 4 Horn Ring

Default Function
System Enable, immediate system shutdown (no delay) ignition OFF
· Siren Mute · Relay 14 OFF · Flashing Takedown Cutoff (LB/ILS/CNSM)
Remote SS1 Activation
Remote SS2 Activation
Remote SS3 Activation
Remote Rumbler® Activation
· When SS2 is Active, SSP Air Horn · When SS3 is Active and PARK is ON, SSP Air Horn · When SS3 and Wail are Active and PARK is OFF, toggles between SSP Yelp and
Wail with Rumbler · When SS3 and Yelp are Active and PARK is OFF, toggles between SSP Priority and
Yelp with Rumbler · When SS3 and Tone 1 are Active and PARK is OFF, SSP Air Horn · When SS3 and Tone 2 are Active and PARK is OFF, SSP Air Horn · When SS3 and HF are Active and PARK is OFF, 4-Step SSP Wail, Yelp, Dual-tone
Wail/Yelp & Priority with Rumbler

Polarity BAT GND
GND GND GND GND GND

Table 7 Global/Miscellaneous Default Programming

Global Audible Dim Level Battery Level

Default Function All buttons 10 No action defined

Refer to the Installation and Maintenance Instructions packed with the Pathfinder® to complete the installation.

Models PF200S17BRK and PF400S17BRK

Federal Signal www.fedsig.com

Pathfinder® 17-Button with Rotary Knob Remote
Getting Technical Support For technical support, please contact:
Federal Signal Corporation Service Department Phone: 1-800-433-9132 Email: empserviceinfo@fedsig.com
Getting Repair Service The Federal Signal factory provides technical assistance with any problems that cannot be handled locally. Any units returned to Federal Signal for service, inspection, or repair must be accompanied by a Return Material Authorization (RMA). Obtain an RMA from a local Distributor or Manufacturer’s Representative. Provide a brief explanation of the service requested or the nature of the malfunction.
Address all communications and shipments to the following:
Federal Signal Corporation Service Department 2645 Federal Signal Dr. University Park, IL 60484-3167
Ordering Replacement Parts To order replacement parts, call Customer Support at 1-800-264-3578, 7 a.m. to 5 p.m., Monday through Friday (CT), or contact your nearest distributor.
Limited Warranty This product is subject to and covered by a limited warranty, a copy of which can be found at www.fedsig.com/SSG-Warranty. A copy of this limited warranty can also be obtained by written request to Federal Signal Corporation, 2645 Federal Signal Drive, University Park, IL 60484, email to info@fedsig.com or call +1 708-534-3400.
This limited warranty is in lieu of all other warranties, express or implied, contractual or statutory, including, but not limited to, the warranty of merchantability, warranty of fitness for a particular purpose and any warranty against failure of its essential purpose.

Models PF200S17BRK and PF400S17BRK

Federal Signal www.fedsig.com

2645 Federal Signal Drive University Park, Illinois 60484-3167

www.fedsig.com

Customer Support Police/Fire-EMS: Work Truck: Technical Support:

800-264-3578 · +1 708 534-3400 800-824-0254 · +1 708 534-3400 800-433-9132 · +1 708 534-3400

Documents / Resources

Federal Signal PF200S17BRK 17 Button With Rotary Knob Remote [pdf] User Guide
PF200S17BRK, PF400S17BRK, PF200S17BRK 17 Button With Rotary Knob Remote, PF200S17BRK, 17 Button With Rotary Knob Remote, Rotary Knob Remote, Knob Remote, Remote

References

User Manual

Federal Signal PF200S17BRK 17 Button With Rotary Knob Remote User Guide

PF200S17BRK 17 Button With Rotary Knob Remote

Product Information

Specifications

Product Usage Instructions

Unpacking the Kit

Connecting the Control Head

Mounting the Control Head

FAQ (Frequently Asked Questions)

Q: What should I do before installation?

Q: What connections are required for the control head?

Documents / Resources

References

Leave a comment

Cancel reply