Remote control
Features
- simple appearance can be applied to different decoration styles.
- split button, more convenient operation.
- Button backlight design.
- Anti-wear anti-scratch material.
- Ultra-low power design.
- AAA(7#) battery, more convenient to install and buy.
- wall fixed seat, more reliable installation.
Parameters
| Model | RF transmit frequency | RF remote control distanoe | Transmit power |
Transmit current |
Standby current | Battery | Working Temp. |
Size |
| AC114-06 | 433.92MHz ±1001(Hz |
i.60m | 410mW | 420mA | cluA | AAA(741’2(3V) | -20°C – +66°C | 12Sx45x15mm (L) (w)(H) |
Installation
- The minimum distance between the launcher and the ground is 1.5m.
- The minimum distance between the receiver and the transmitter 1m.
- Do not install on metal objects, Otherwise, the launching distance will be affected.
- Do not install in wet and exposed places, Otherwise, it will affect the service life of the machine.
Cautions
While complying with the standards for efficient use of electricity, please comply with the following requirements:
- Transmission range: within 80 meters of open space
- Avoid static interference, static electricity will damage some electronic components
Opetations
- Control
Uplink button: Uplink control
Stop key: Stop
Downlink: Downlink control - Channel selection
Right frequency key: channel increment
Left frequency key: channel decrease - Frequency locking (6-frequency and 16-frequency available)
Frequency lock: press the “Stop key” + any “frequency select key until the indicator lights up (about 3 seconds) to lock the frequency of the current channel, after locking the current channel is the maximum number of channels of the transmitter, the channel after the current channel will not be available.
Unlock frequency: under any channel, press the “Stop key + any “frequency selection key” again until the indicator lights up (about 3 seconds) to unlock the channel.
Trouble shooting
| Problems | Analysis | Solutions |
| When operating the transmitter. the receiver no act | 1.The receiver is not working properly 2.The battery of transmitter is out of power. |
A.The receiver works normally B.Replace a new battery of transmitter |
| The receiver is not working properly | The battery of transmitter is out of power | Replace a new battery of transmitter |
Cautions
a) The statement “Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate.
b) The statement “Even used batteries may cause severe injury or death.
c) The statement “Call a local poison control center for treatment information.
d) A statement indicating the compatible battery type (e.g., LR44, AAA(7#)*2(3V)).
e) A statement indicating the nominal battery voltage.
f) The statement “Non-rechargeable batteries are not to be recharged.
g) The statement “Do not force discharge, recharge, disassemble, heat above (manufacturer’s specified temperature rating) or Incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns.
h) The statement “Ensure the batteries are installed correctly according to polarity (+ and-).
The statement “Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations.
1) The statement “Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries. 1)
k) The statement “Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.
This device complies with Part 15 of the FCC rules. Operation is subjected to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are d esigned to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development (ISED) Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
The device has been evaluated to meet general RF exposure requirement.
Documents / Resources
 |
Fdit AC114-06 Smart Home Automatic Curtain Control System [pdf] User Guide 2AVVD-AC114, 2AVVDAC114, ac114, AC114-06 Smart Home Automatic Curtain Control System, AC114-06, Smart Home Automatic Curtain Control System, Automatic Curtain Control System, Control System, System |