SP630E-12in1-01 SPI plus 5ch PWM All in One Bluetooth LED Controller
Product Information
Specifications:
- Product: LED Strip Power Supply
- Output Voltage: Depends on LED strip
Product Usage Instructions:
1. Checking Compatibility:
Before connecting the LED strip power supply, ensure that it is
compatible with your LED strip specifications. Verify the voltage
requirements of your LED strip to avoid damage.
2. Connection:
Connect the power supply to the designated power source. Make
sure to match the polarity correctly to prevent short circuits.
3. Adjusting Output Voltage:
Based on the LED strip requirements, adjust the output voltage
of the power supply accordingly. Refer to the LED strip
manufacturer’s guidelines for the recommended voltage.
4. Testing:
After connection, test the LED strip with the power supply to
ensure proper functionality. Observe the brightness and color
consistency of the LEDs.
5. Maintenance:
Regularly inspect the power supply for any signs of wear or
overheating. Keep the area around the power supply well-ventilated
to prevent overheating issues.
Frequently Asked Questions (FAQ):
Q: What should I do if the output voltage does not match my LED
strip?
A: In case of voltage mismatch, do not connect the power supply
to the LED strip as it can damage the LEDs. Contact the
manufacturer for assistance in selecting a compatible power
supply.
Q: Can I use this power supply for outdoor LED strips?
A: It is recommended to use weatherproof or outdoor-rated power
supplies for outdoor LED strips to ensure safe operation and
longevity.
The output voltage of the power supply depends on LED strip
0
r<–evccee= SPB30E
0
0-r-æ rC 8 8 GHD SP630E
reCeR eG eB erö ree rTGeN
0
VCC R G 8 CW ‘MVOATGN 88 8 889 8 8
4.13 SPI RGB+PWM Single Color LED Strip
a.,II)
. ; ., !
II)
tfaa,,
oil)
·II>
II)
Set LED Type
Color Correction
@
0
4.14 SPI RGB+PWM CCT LED Strip
a.,II)
I !
II)
II)
fa, ta,
·II)
oil)
·II)
II)
Set LED Type
Color Correction
@ §} l;jj;) l;jj;)
6
Different types of LED correspond to different output ports; The ports should match the selected LED type. and the specific port descriptions as follows:
5. 2.4G RF Remote/Smart Panel Control
(Purchased separately)
— ·· eelcm,a Please set the LED type on the APP before using the remote/panel to control LED controller.
1 CHPWM Single Color
2CH PWMCCT
———— — —
CPWD3MC® RHGB iIi CPWDM4 CR® HGBW
5 CH I
SPI
PWMRGBCCT l Single Color
·· ee1ee1ee ee[ee SP!CCT
SPI RGB
SPI RGBW SPI RGBCCT
‘
i I
SPI RGB +lCHPWM
PB !+2C J CCT
Handheld RF Remote (Purchased separately)
· ·· ·· ·· ·
!1
!2
,.,
RBJ
GD GD
86-Type RF Wall panel remote (Purchased separately)
0
0 0
0 0
! (-
!
l_·)
0 0
6. 4 Zones Group Control
The Remotes support 4 zones control and unified control. One RF remote can control up to 4 groups of lights. Each group can control LED strips within 30m (98ft). Besides, one RF remote can control multiple controllers and each controller is able to bind up to 5 RF remotes.
Linking Instructions
LED strip light Power supply
0 0
LED strip light Power supply
@ The LED strip blinking means
linking successfully.
If LED strip doesn’t light up, it rnay be due to the poor connection between the controller and the
LED strip. Please try to reconnect all wires. To avoid signal interference when setting the specific zone control, please only power up the
controller of that zone.
Unlinking Instructions
LED strip light Power supply
0 0
0
Disconnect the LED controller from the power supply for 10
seconds and reconnect it.
When the light is on, long press the “ALL· key within 20 seconds to set the
remote to unlink the controllers.
LED strip light Power supply
&,
If LED strip doesn’t light up, it may be due to the poor connection between the controller and the
LED strip. Please try to reconnect all wires. If LED strip doesn’t blink, it means unlinking failed.
Please follow above steps to try it again.
The LED strip blinking means unlinking successfully.
7. APP Installation
1. SP630E supports APP control for iOS and Android devices. 2. Apple devices require iOS 10.0 or higher, and Android
devices require Android 4.4 or higher. 3.You can search “BanlanX” in App Store or Google Play to
find the APP, or scan the QR code to download and install.
8 APP Operation Instructions
8.1 Add Device
· Enter the Device Search Page: Click the “Add Device” button to the device search page. To ensure searching smoothly, please make sure your phone is close to the target device and Bluetooth is turned on.
· Select and Add the Device: Select the target device and complete the addition process.
Add device M,tnua:y
Searching nearby devices… ., “r” l”>’!'<“1′”‘-“‘ft·<‘OW<1l’-eW·<,”lfln:.1
SP6J0£
Settings
I .. Modifyllghtrpc-
e CclorCcuectk,n
O Timt!rl
@ OWOlfMode
Lighting parameters
.lr
8.3 Group Control
Before setting group control, please set the LED type and complete the color correction of each controller first. LED strips and controllers must be of the same type.
Then enter the Groups setting page to add devices to group. (Note: At least 2 and up to 5 devices)
Guest
0
Groups
fi
No group
8.4 Function Introduction
Four APP operating interfaces: Dynamic, Static, Music and DIY. Besides, click therì icon to enter the settings page, where you can modify the name, modify the type of LED, calibrate the color order, set the timings, set the on/off effect.etc.
· Music Function: Adjust the color and lighting effect according to the
music automatically. Support 3 kinds of music capture modes: player streaming, built-in microphone, cell phone microphone (phone microphone requires access from phone).
· DIV Function: You can adjust light color, number of IC chip and light
mode to set the lighting effect for your LED strip as you wished.
·
· @ 0
r
··· ·· RrçrÄlat
Dynamic
Static
·
FU:.C<l!Ol’ll1¥M’S.O.cm,n,
@ ,9 -9,
G ·
Music
6j;’
0
Disconnect the LED controller from the power supply for 10
seconds and reconnect it.
When the light is on, long press any key of 4 zones within 20 seconds to set the
remote to control a specific zone.
7
8.2 LED Type Setting and Color Correction
Please enter the setting page to adjust the LED parameters based on the connected LED type and follow the prompts to complete the color correction test.
8
Number 6 represents the number of IC chip
DIV
Pure White
9
9. Causes of Connection Failure and the Solution
(1) LED Strip only lights up Red light. No other color can be lit. A: Please check if the power supply voltage matches the voltage of LED light. ff your
strip is DC24V, use a DC24V power supply.
(2) LED strip goes off when lighting up White light. A: If your light is RGB type. we suggest you don’t light up white light as the mixed
white(R+G+B) consumes very high power. Insufficient power causes the strip to go off.
(3) Not connect the light strip with the controller correctly. A: Please read the wiring diagram of the manual carefully before connecting. Make
sure you have connected them correctly then to connect the power supply.
(4) Not set the LED type correctly. A: Please check if you have set the LED type on the APP correctly. You could refer
to Part 4 of the manual for specific settings.
(5) Bluetooth is not turned on. A: Please turn on Bluetooth and make sure it didn’t connect other devices such as
earphones, stereos, etc.
(6) The insufficient power of the power supply may cause the controller disconnection, Bluetooth disconnection, or light flickering .
A: Please use a power supply with higher power. Insufficient power will cause many problems. If you don’t know how to calculate the power of LED light strips, please contact us and we could help.
(7) RF remote/Panel can’t link to the controller. A: Please power off, then power on again. Make sure your operation is within 20
seconds after the controller is powered on.
(8) You can use the BanlanX APP but the LED strip can’t b e lit. A: The controller and the LED strip are in poor connection. Please try to
reconnect all wires. A: The data direction of SPI LED strip is wrong, please check the little arrow on the
PC board.
10.Attention
1. Please connect the strip and the controller according to the wiring diagram correctly.
2. Please select a right RF remote/panel for the exact LED type.
3. Please select an appropriate power supply according to the light. If the light
is DC12V, then do not use a DCSV/DC24V power supply.
4. Please do not connect power supply above 24V. The working voltage of the
controller is DC5-24V.
5. Please do not touch the smart panel within 2s after installing the new battery.
6. Please do not use the product in high humidity, high temperature, dusty
and high pressure environment.
7, Please do not use controller around the mental area and high magnetic field,
otherwise it will seriously affect the remote control distance. 8. Please take the strip off the roll when powering on as the strip on the roll is
not conducive to heat dissipation, which may damage the strip.
/ECIREPI
COMPANY NAME: XDH Tech ADDRESS: 2 Rue Coysevox Bureau 3.69001, Lyon, France CONTACT PERSON: Dinghao Xue
Our team can also provide you with such services!
lf you are not sure about the strip lighting project for stairs, wine c2binet, ceiling, hallway, cabinet. please contact us in time, we will provide professional design proposal.
Global customer service: contact@btf-lighting.com US Amazon customer service: support@btf-lighting.com EU/UK Amazon customer service: rachel@btf-lighting.com
Made In China
10
Documents / Resources
 | FCOB SP630E-12in1-01 SPI plus 5ch PWM All in One Bluetooth LED Controller [pdf] Instruction Manual 24V-RGBCCTCNTRL, SP630E-12in1-01 SPI plus 5ch PWM All in One Bluetooth LED Controller, SP630E-12in1-01, SPI plus 5ch PWM All in One Bluetooth LED Controller, 5ch PWM All in One Bluetooth LED Controller, PWM All in One Bluetooth LED Controller, All in One Bluetooth LED Controller, Bluetooth LED Controller, LED Controller, Controller |