F-US04A Smart Switch
Specifications:
- Rated voltage: 100-240V
- Wifi type: 2.4Ghz
- Operating temperature: -10~45
- Rated power: 1000-2400
- Load current: 10A
- Size: 72*118*35mm
Product Usage Instructions:
Installation:
- Fix the switch onto the wall.
- Put the switch lower parts into the switch box in the
wall. - Mount the two side screws securely.
- Install the upper top case by placing it from above.
- Cover the upper top case onto the switch.
- Turn on electricity, and the LED light will flash quickly for
pairing.
FCC Warning:
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including
interference that may cause undesired operation.
To address interference issues, consider the following:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver. - Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for
help.
NOTE 2: Any changes or modifications to this
unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
RF Exposure Statement:
To maintain compliance with FCC’s RF Exposure guidelines, this
equipment should be installed and operated with a minimum of 20cm
between the radiator and your body. This device and its antenna(s)
must not be co-located or operated in conjunction with any other
antenna or transmitter.
FAQ:
Q: What should I do if the LED light does not flash during
pairing?
A: Make sure the electricity is turned on and check the
installation to ensure all steps were followed correctly. If the
issue persists, contact customer support for assistance.
Smart Switch User manual
1Gang Smart Switch
Rated voltage: 100-240V Wifi type: 2.4Ghz Operating temperature: -10~45 Rated power: 1000-2400 Load current: 10A SIZE:72*118*35mm
L4 L3 L2 L1 L N
2Gang Smart Switch
Rated voltage: 100-240V Wifi type: 2.4Ghz Operating temperature: -10~45 Rated power: 1000-2400 Load current: 10A SIZE:72*118*35mm
L4 L3 L2 L1 L N
L4 L3 L2 L1 L N
3Gang Smart Switch
Rated voltage: 100-240V Wifi type: 2.4Ghz Operating temperature: -10~45 Rated power: 1000-2400 Load current: 10A SIZE:72*118*35mm
4Gang Smart Switch
Rated voltage: 100-240V Wifi type: 2.4Ghz Operating temperature: -10~45 Rated power: 1000-2400 Load current: 10A SIZE:72*118*35mm
In d ica to r Lig h t
L4 L3 L2 L1 L N
7
L 1 bu tto n
L 2 bu tto n
L 3 bu tto n
L 4 bu tto n
3. Fix the switch onto wall. 3.1 Put the switch lower parts into switch box in the wall. 3.2 Mount the two side screws. 3.3 Install the upper top case (install from up above). 3.4 Cover the upper top case into switch. 3.5 Turn on electricity, and then LED light will be flashed quickly for pairing.
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
RF Exposure Statement To maintain compliance with FCC’S RF Exposure guidelines, This equipment should be installed and operated with minimum 20cm between the radiator and your body. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter
Documents / Resources
 |
Farylink F-US04A Smart Switch [pdf] User Manual F-US04A, F-US04A Smart Switch, Smart Switch, Switch |