FADINI Jubi 433 4 Button Radio Transmitter Instruction Manual

1st Channel: Insert STRIP in position 1, then
press button P and a transmitter button simultaneously for 5
seconds.
2nd Channel: Repeat the above steps with STRIP
in position 2.

3rd Channel: Repeat the above steps with STRIP
in position 3.
4th Channel: Repeat the above steps with STRIP
in position 4.

Note: After completion of all tests, remove the
STRIP and place it on one PIN only to stop any further linking or
operational action.

Frequently Asked Questions (FAQ):

Q: How do I know if the encoding process was successful?

A: A successful encoding will be confirmed by a flash of the LED
on the receiver unit.

Q: Can I encode multiple transmitters for a single
channel?

A: Yes, each channel can store up to 25 transmitter codes.

“`

View Fullscreen

24 VOLT c.a. ALIMENTAZIONE
1° CANALE 2° CANALE 3° CANALE 4° CANALE
12-2010

Jubi 433
– da esterno – external – modulaire – Aufputzversion – para exterior – voor buitenmontage

– Cod. Art. 4330 –
0678
11 12 13

1°R

P1 1 3 P2 2 4 I.T.F.

RSJUBI

9 10 11 12

ANTENNA +

2°R

3°R

4°R

5
3

Fig.1

I a) CONOSCERE LA MEMORIA LIBERA -P1-

DESCRIZIONE COMPONENTI Fig.1

Per conoscere quanta memoria libera è disponibile nella ricevente, con la scheda 1 – Memoria estraibile

alimentata a 24 Volt, si deve inserire il ponticello “STRIP” nella posizione P1 e premere il pulsante 2 – Pulsante “P”

P per cinque secondi: rilasciandolo si possono notare dei lampeggi. Ad ogni lampeggio di led 3 – Led

corrispondono 25 trasmettitori che si possono ancora memorizzare.

4 – Ponticelli 1°-2°-3°-4° canale: scelta da 1 a 4

b) CANCELLAZIONE TOTALE DELLA MEMORIA -P2-

pulsanti del trasmettitore

Per cancellare la memoria nella ricevente, con la scheda alimentata a 24 Volt, si deve inserire il 5 – Inserto di contatto “STRIP” ponticelli

ponticello “STRIP” nella posizione P2 e premere il pulsante P per cinque secondi; poi lo si 6 – Connettore per modulo a relè 4° canale

rilascia, e in quel momento il led emette un impulso di luce: questo indica che l’operazione di 7 – Morsettiera di collegamento alimentazione a

cancellazione è avvenuta.

24 V, 1°-2°-3°-4° canale e antenna

c) CODIFICA 1° CANALE -1-

8 – Modulo a relè N.A. per il 4°canale (OPTIONAL)

Per codificare il 1° canale si deve inizialmente posizionare lo “STRIP” in posizione 1; si deve 9 – Modulo a relè N.A. per il 3°canale (OPTIONAL)

poi premere contemporaneamente per cinque secondi il pulsante P e un tasto a scelta del 10 – Modulo a relè N.A. per il 2°canale (OPTIONAL)

trasmettitore. Il led emetterà successivamente un impulso spia a conferma dell’avvenuta 11 – Connettore per modulo a relè 3° canale

memorizzazione del codice.

12 – Connettore per modulo a relè 2° canale

d) CODIFICA 2° CANALE -2-

13 – Modulo a relè per il 1° canale (di SERIE)

Per codificare il 2° canale si procede come descritto nel punto “c” con la sola eccezione di 14 – Contenitore radio ricevente da esterno Jubi 433

posizionare lo “STRIP” in posizione 2.

e) CODIFICA 3° CANALE -3-

Per codificare il 3° canale si procede come descritto nel punto “c” con la sola eccezione di posizionare lo “STRIP” in posizione 3.

f) CODIFICA 4° CANALE -4-

Per codificare il 4° canale si procede come descritto nel punto “c” con la sola eccezione di posizionare lo “STRIP” in posizione 4.

NOTA: è importante che, al termine dei test a,b,c,d,e,f si tolga il ponticello “STRIP” e lo si inserisca in un solo “PIN”, in modo che non faccia più da contatto.

Scheda radio ricevente da esterno “Jubi 433/4 R” con risuonatore stabilizzato al quarzo, completa di un relè per il 1° canale, frequenza 433,92 MHz.

GB a) FREE MEMORY MONITORING -P1-

COMPONENTS DESCRIPTION Pic.1

Monitoring the free portion, ie. storage availability in the receiver memory. 24 Volt 1 – Removable memory

power supply still connected to the unit. Insert the “STRIP” jumper as in position “P1” and 2 – Switch button “P”

press the button switch “P” for 5 seconds: after releasing it, a number of flashes can be noted. 3 – Led

Each flash of light through the “LED” corresponds to 25 transmitters that can be still encoded 4 – Pins for channels 1-2-3-4: any one transmitter

and stored in the memory.

button 1 to 4 can be selected

b) TOTAL MEMORY REMOVAL -P2-

5 – “STRIP” contact insert pins

To perform the total removal of the receiver encoded memory, position the “STRIP” jumper as 6 – Module connector for channel 4

in “P2”, the receiver still under 24 Volt voltage supply. Press the switch button “P” for 5 seconds, 7 – Terminal to connect channels No. 1-2-3-4,

then release it. The led flashes once to confirm that the removal operation has been carried

24 V power supply and aerial

out completely.

8 – Relay N.O. to activate channel No.4 (OPTION)

c) ENCODE 1st CHANNEL -1-

9 – Relay N.O. to activate channel No.3 (OPTION)

To encode channel No.1, first insert the “STRIP” jumper in position “1”; the next step is to 10 – Relay N.O. to activate channel No.2 (OPTION)

press simultaneously the switch button “P” on the receiver card and a push button (any desired 11 – Module connector for channel 3

one) on the transmitter for about 5 seconds. Once the code has been memorized by the unit, 12 – Module connector for channel 2

the led flashes once.

13 – Relay N.O. to activate channel No.1 (STANDARD)

d) ENCODE 2nd CHANNEL -2-

14 – Weather-proof radio receiver container Jubi 433

To encode channel No.2 repeat the above sequence “c”,but the “STRIP” jumper must be inserted

in position “2”.

e) ENCODE 3rd CHANNEL -3-

To encode channel No.3 repeat the above sequence “c”,but the “STRIP” jumper must be inserted in position “3”.

f) ENCODE 4th CHANNEL -4-

To encode channel No.4 repeat the above sequence “c”,but the “STRIP” jumper must be inserted in position “4”.

NB: Once the tests a,b,c,d are finished, remove the “STRIP” and put it on to one “PIN” only, to stop any linking, ie. operative action.

Radio receiver card type “Jubi 433/4 R” fitted with stabilized resonator, complete with one relay module for channel 1. Frequency 433.92 MHz.

Dis. N. 2878

Via Mantova, 177/A – C.P. 126 – 37053 Cerea (Verona) Italy – Tel. +39 0442 330422 r.a.
®
Fax +39 0442 331054 – e-mail: info@fadini.net – www.fadini.net

a) CONNAITRE LA MEMOIRE LIBRE -P1Pour connaître la mémoire libre dans le récepteur radio il faut qu’il soit alimenté et enficher le cavalier “STRIP”

sur la position “P1”. Ensuite en appuyant sur le bouton-poussoir “P”, on obtient au bout de 5 secondes un ou

plusieurs clignotements de la “LED”. Chaque clignotement correspond à 25 émetteurs. b) EFFACER TOTALEMENT LA MEMOIRE -P2-

Pour effacer totalement la mémoire d’un récepteur, et donc tous les émetteurs enregistrés, il faut que la carte soit alimentée

en 24 Volts. Vous devez ensuite insérer le cavalier “STRIP” sur la position “P2” et actionner le poussoir “P” durant 5

secondes, puis le relâcher. Un moment après, la led de signalisation èmettra une impulsion lumineuse qui indiquera que

l’opération d’effacement est terminée. c) MEMORISATION 1ère CANAL -1-

Pour rentrer le 1ère canal, il faut d’abord mettre le cavalier “STRIP” sur la positionn “1”; puis appuyer simultanement sur le poussoir “P” du récepteur et une touche de l’émetteur durant 5 secondes. Lorsque le code est enrégistré le voyant

“LED” s’allume pour confirmer la prise en compte du code. d) MEMORISATION 2ème CANAL -2-

Pour rentrer le 2ème canal procéder de la même façon que ci-dessus en mettant le cavalier “STRIP” sur la position “2”. e) MEMORISATION 3ème CANAL -3-

Pour rentrer le 3ème canal procéder de la même façon que ci-dessus en mettant le cavalier “STRIP” sur la position “3”. f) MEMORISATION 4ème CANAL -4-

Pour rentrer le 4ème canal procéder de la même façon que ci-dessus en mettant le pontet “STRIP” sur la position “4”. NOTE: Aprés les opérations a,b,c,d, il est important d’enlever le cavalier “STRIP” et le mettre sur un seul “PICOT”, pour

éviter des contacts.

Récepteur radio modulaire “Jubi 433/4 R” avec résonateur stabilisé complet d’un module relais pour le 1ère canal, fréquence

433,92 MHz.

DESCRIPTION DES COMPOSANTS Fig.1
1 – Mémoire enfichable 2 – Poussoir “P” 3 – Led 4 – Ponts 1°-2°-3°-4° canal: choisir l’émetteur
de 1 à 4 poussoirs max. 5 – Cavalier “STRIP” 6 – Connecteur pour module relais 4ème canal 7 – Borne de raccordement 1°-2°-3°-4° canal,
antenne et alimentation 24 V 8 – Relais pour actionner le 4ème canal (OPTION) 9 – Relais pour actionner le 3ème canal (OPTION) 10 – Relais pour actionner le 2ème canal (OPTION) 11 – Connecteur pour module relais 3ème canal 12 – Connecteur pour module relais 2ème canal 13 – Relais pour actionner le 1ère canal (de SERIE) 14 – Boîtier récepteur radio Jubi 433 modulaire

a) PRÜFEN WIEVIEL PLATZ IM SPEICHER FREI IST -P1Um zu erfahren wieviel Platz in dem Speicher des Empfängers noch vorhanden ist, muss man bei mit 24 Volt

gespeistem Modul die “STRIP” Codierbrücke in die Position “P1” einfügen und die Taste “P” 5 Sekunden lang

drücken: lässt man die Taste los, so kann man ein Blinken erkennen. Jedem Blinken des LEDs entsprechen 25 Handsender,

die noch gespeichert werden können.

b) KOMPLETTES LÖSCHEN DES SPEICHERS -P2-

Um den gesamten codierten Speicher auf dem Funkempfänger zu löschen, den “STRIP” Codier-brücke in Position “P2”

stecken, wobei die Platine immer mit 24 Volt versorgt wird. Die Taste “P” muss 5 Sekunden lang gedrückt werden, danach

lässt man sie los, in diesem Moment sendet das LED einen Lichtimpuls, der anzeigt, dass der Löschvorgang erfolgt ist.

c) EINGABE 1. KANAL -1-

Um den 1. Kanal zu codieren, die “STRIP” Brücke in die Position “1” stecken, danach gleichzeitig die Taste “P” und eine

Taste des Handsenders (nach Wahl) ungefähr 5 Sekunden lang drücken. Dadurch wird die LED Signalleuchte aufleuchten,

wodurch uns die erfolgte Einspeicherung des Codes bestätigt wird.

d) EINGABE 2. KANAL -2-

Um dem 2. Kanal zu kodieren, wie oben Position “c” beschrieben vorgehen, die einzige Unterschied ist, dass die “STRIP”

Brücke in die Position “2” gesteckt wird.

e) EINGABE 3. KANAL -3-

Um dem 3. Kanal zu kodieren, wie oben Position “c” beschrieben vorgehen, die einzige Unterschied ist, dass die “STRIP”

Brücke in die Position “3” gesteckt wird.

f) EINGABE 4. KANAL -4-

Um dem 4. Kanal zu kodieren, wie oben Position “c” beschrieben vorgehen, die einzige Unterschied ist, dass die “STRIP”

Brücke in die Position “4” gesteckt wird.

NB: Nachdem man die Test a,b,c,d durchgeführt hat die “STRIP” Codierbrücke entfernen und sie in einen einzigen “PIN”

stecken, damit er keinen Kontakt mehr macht. Empfangsplatine Typ “Jubi 433/4 R” mit stabilisiertem Resonator komplett

mit Relaismodul für den 1. Kanal, Frequenz 433,92 MHz.

BESCHREIBUNG DER BESTANDTEILEN Abb.1
1 – Abnehmbarer Speicher 2 – Taste “P” 3 – Led 4 – 1.-2.-3.-4. Kanal Anschlüsse: Wahl des
Sendersauslösers von 1 bis 4 max. 5 – “STRIP” Codierbrücke 6 – Verbinder für Relais 4. Kanal 7 – Klemme 1.-2.-3.-4. Kanal,
Antenne und Stromversorgung 24 V 8 – Relais N.O. zur Steuerung des 4. Kanals (OPTION) 9 – Relais N.O. zur Steuerung des 3. Kanals (OPTION) 10 – Relais N.O. zur Steuerung des 2. Kanals (OPTION) 11 – Verbinder für Relais 3. Kanal 12 – Verbinder für Relais 2. Kanal 13 – Relais N.O. Zur Steuerung des 1. Kanals (STANDARD) 14 – Gehäuse für Funkempfänger Jubi 433 Aufputzversion

a) PARA CONOCER LA MEMORIA LIBRE -P1Para averiguar cuanta memoria está disponible en el radiorreceptor, siempre estando la ficha alimentada a 24

Voltios, hay que conectar el puente “STRIP” en la posición “P1” y apretar el pulsador “P” durante 5 segundos:

soltandolo se pueden observan unos relampagueos. Cada relampagueo de led señala que hay 25 transmisores que pueden

DESCRIPCION COMPONENTES Fig.1 1 – Memoria amovible 2 – Pulsador “P”

memorizarse aun. b) BORRADURA TOTAL DE LA MEMORIA -P2-
Se borra toda la memoria codificada en el receptor colocando el “STRIP” como un puente en la posición “P2”, siempre estando alimentada la ficha misma a 24 Voltios. Se aprieta el pulsador “P” durante 5 segundos, se le suelta y en aquel

3 – Led 4 – Puentes 1er-2°-3°-4° canal: elección desde 2
hasta 4 pulsadores del transmisor

momento el led emite un impulso luminoso, que señala que la operación de borradura se ha realizado. c) CODIFICACION 1er CANAL -1-
Para codificar el 1er canal, colocar ante todo el “STRIP” en la posición “1”; a continuación, apretar al mismo tiempo durante 5 segundos el pulsador “P” e una tecla a elección del transmisor. El led emitirá después una impulsión de luz

5 – Pieza de contacto “STRIP” puentes 6 – Conectador para módulo de relé 4° canal 7 – Borne de conexión 1er-2°-3°-4° canal,

para confirmar que el código ha sido memorizado. d) CODIFICACION 2° CANAL -2-
Para codificar el 2° canal, actuar como reseñado en el apartado “c” excepto únicamente que se coloca el “STRIP” en la posición “2”.

antena y suministro de corriente 24V 8 – Relè N.A. para activar el 4°canal (OPTION) 9 – Relè N.A. para activar el 3°canal (OPTION)

e) CODIFICACION 3° CANAL -3Para codificar el 3° canal, actuar como reseñado en el apartado “c” excepto únicamente que se coloca el “STRIP” en la posición “3”.
f) CODIFICACION 4° CANAL -4-

10 – Relè N.A. para activar el 2°canal (OPTION) 11 – Conectador para módulo de relé 3° canal 12 – Conectador para módulo de relé 2° canal

Para codificar el 4° canal, actuar como reseñado en el apartado “c” excepto únicamente que se coloca el “STRIP” en la posición “4”. NOTA: es importante que al final de los ensayos a,b,c,d, se quiete el puente “STRIP” y se lo introduzca en un sólo “PIN”,

13 – Relè N.A. para activar el 1er canal (ESTANDARD) 14 – Contenedor radioreceptor para exterior Jubi 433

de forma que el mismo no haga más contacto.

Ficha radiorreceptor “Jubi 433/4 R” con resonador estabilizado de cuarzo, equipada de módulo relé para el 1er canal, frequencia 433,92 MHz.

NL a) OM HET VRIJE GEHEUGEN TE WETEN -P1Om te weten hoeveel vrije geheugen er in de ontvanger beschikbaar is, met de kaart met een stroomtoevoer van 24 Volt, moet de “STRIP” geleiderbrug op positie “P1” worden ingestoken en moet drukknop “P” gedurende vijf seconden worden ingedrukt; wanneer deze wordt losgelaten kunnen er flikkerlichten worden opgemerkt. Elk flikkerlicht

BESCHRIJVING ONDERDELEN (FIG.1) 1 – Uitneembaar geheugen 2 – Drukknop “P”

van de lichtdiode komt overeen met 25 zenders waarin nog gegevens kunnen worden opgeslaan. b) TOTALE ANNULERING VAN HET GEHEUGEN -P2-
Om het geheugen in de ontvanger te annuleren, met de kaart met een stroomtoevoer van 24 Volt, moet de “STRIP” geleiderbrug op positie “P2” worden ingestoken en moet drukknop “P” gedurende vijf seconden worden ingedrukt; hierna

3 – Led 4 – Geleiderbruggen 1-2-3-4 kanaal: keuze uit 1
to 4 drukknoppen van de zender

moet deze worden losgelaten en zal de lichtdiode op dat moment een lichtsignaal afgeven: dit geeft aan dat de annuleringshandeling is uigevoerd. c) CODERING 1e KANAAL -1-

5 – Inzetcontact “STRIP” geleiderbruggen 6 – Moduulrelaisconnector 4e kanaal

Om het 1e kanaal te coderen moet de “STRIP” aanvankelijk op positie “1” worden ingesteld: daarna moet men tegelijkertijd 7 – Verbindingsklem 1-2-3-4 kanaal,

gedurende vijf seconden drukknop “P” drukken en een toets van de zender naar keuze indrukken. De lichtdiode zal hierna een verklikkersimpuls afgegeven ter bevestiging dat de code in het geheugen is opgeslaan. d) CODERING 2e KANAAL -2Om het 2e kanaal te coderen moet men handelen zoals in punt “c” is beschreven met het enige verschil dat de “STRIP”

antenne en stroomtoevoer van 24 V 8 – Relais om het 4e kanaal te activeren (OPTION) 9 – Relais om het 3e kanaal te activeren (OPTION)

op positie “2” moet worden ingesteld. e) CODERING 3e KANAAL -3-
Om het 3e kanaal te coderen moet men handelen zoals in punt “c” is beschreven met het enige verschil dat de “STRIP” op positie “3” moet worden ingesteld. f) CODERING 4e KANAAL -4Om het 4e kanaal te coderen moet men handelen zoals in punt “c” is beschreven met het enige verschil dat de “STRIP” op positie “4” moet worden ingesteld.

10 – Relais om het 2e kanaal te activeren (OPTION) 11 – Moduulrelaisconnector 3e kanaal 12 – Moduulrelaisconnector 2e kanaal 13 – Relais om het 1e kanaal te activeren (STANDARD) 14 – Buitendoos voor radio-ontvanger Jubi 433

OPMERKING: Het is belangrijk dat na test a,b,c,d, de “STRIP” geleiderbrug wordt weggenomen en dat men deze in één

“PIN” steekt zodat deze geen contact meer tot stand brengt.

Kaart ontvangstradio “Jubi 433/4 R” met gestabiliseerde kwartsresonator, compleet met relaismodule voor het 1e kanaal, frequentie 433,92 MHz.

Dis. N. 2878

Via Mantova, 177/A – C.P. 126 – 37053 Cerea (Verona) Italy – Tel. +39 0442 330422 r.a.
®
Fax +39 0442 331054 – e-mail: info@fadini.net – www.fadini.net

09-2010

Jubi 433
– ad innesto – plug-in – enfichable – Einsteckversion – enchufable – met koppeling

– Cod. Art. 4332 –
0678
12

2°R

1°R

1 2
JUBI

P2 P1

12 3 4 5

24V Relé

10
N.C. C N.A. ANTENNA
98

Fig.1

I a) CONOSCERE LA MEMORIA LIBERA -P1-
Per conoscere quanta memoria libera è disponibile nella ricevente, con la scheda alimentata a 24 Volt, si deve inserire il ponticello “STRIP” nella posizione “P1” e premere il pulsante “P” per
cinque secondi: rilasciandolo si possono notare dei lampeggi. Ad ogni lampeggio di led corrispondono
25 trasmettitori che si possono ancora memorizzare. b) CANCELLAZIONE TOTALE DELLA MEMORIA -P2-
Per cancellare la memoria nella ricevente, con la scheda alimentata a 24 Volt, si deve inserire il ponticello “STRIP” nella posizione “P2” e premere il pulsante “P” per cinque secondi; poi lo si

DESCRIZIONE COMPONENTI Fig.1
1 – Memoria estraibile 2 – Pulsante “P” 3 – Inserto di contatto “STRIP” ponticelli 4 – Ponticelli 1°-2° canale: scelta da 1 a 4 pulsanti
del trasmettitore 5 – Led 6 – Relé per attivare il 2° canale 7 – Morsettiera di collegamento 2° canale contatto

rilascia, e in quel momento il led emette un impulso di luce: questo indica che l’operazione di
cancellazione è avvenuta. c) CODIFICA 1° CANALE -1-
Per codificare il 1° canale si deve inizialmente posizionare lo “STRIP” in posizione “1”; si deve poi premere contemporaneamente per cinque secondi il pulsante “P” e un tasto a scelta del
trasmettitore. Il led emetterà successivamente un impulso spia a conferma dell’avvenuta

N.C.-N.A. e antenna (morsetti 1-2) 8 – Connettore ad innesto femmina 1° canale e
alimentazione a 24 V 9 – Relé per attivare il 1° canale 10 – Programmatore elettronico serie Elpro 11 – Connettore ad innesto maschio

memorizzazione del codice.

d) CODIFICA 2° CANALE -2-

Per codificare il 2° canale si procede come descritto nel punto “c” con la sola eccezione di posizionare lo “STRIP” in posizione “2”.

NOTA: è importante che, al termine dei test a,b,c,d, si tolga il ponticello “STRIP” e lo si inserisca in un solo “PIN”, in modo che non faccia più da

contatto.

Scheda ad innesto radio ricevente “Jubi 433/2 R” con risuonatore stabilizzato al quarzo, completa di due moduli relè per il 1° e 2° canale, frequenza

433,92 MHz.

GB a) FREE MEMORY MONITORING -P1-
Monitoring the free portion, ie. storage availability in the receiver memory. 24 Volt power supply still connected to the unit. Insert the “STRIP” jumper as in position “P1” and press the button switch “P” for 5 seconds: after releasing it, a number of flashes can be noted. Each
flash of light through the “LED” corresponds to 25 transmitters that can be still encoded and
stored in the memory. b) TOTAL MEMORY REMOVAL -P2-

COMPONENTS DESCRIPTION Pic.1
1 – Removable memory 2 – Switch button “P” 3 – “STRIP” contact insert pins 4 – Pins for channels 1-2: any one transmitter
button 1 to 4 can be selected 5 – Led 6 – Relay to activate channel No.2

To perform the total removal of the receiver encoded memory, position the “STRIP” jumper as 7 – Terminal to connect N.O. n N.C. channel No.2

in “P2”, the receiver still under 24 Volt voltage supply. Press the switch button “P” for 5 seconds,
then release it. The led flashes once to confirm that the removal operation has been carried out
completely. c) ENCODE 1st CHANNEL -1-
The encode channel No.1, first insert the “STRIP” jumper in position “1”; the next step is to press simultaneously the switch button “P” on the receiver card and a push button (any desired

and aerial (Terminals 1-2) 8 – Female plug-on connector channel 1 and 24 V
power supply 9 – Relay to activate channel No.1 10 – Electronic programmer Elpro series 11 – Male plug-on connector

one) on the transmitter for about 5 seconds. Once the code has been memorized by the unit,

the led flashes once.

d) ENCODE 2nd CHANNEL -2-

To encode channel No.2 repeat the above sequence “c”,but the “STRIP” jumper must be inserted in position “2”.

NB: Once the tests a,b,c,d are finished, remove the “STRIP” and put it on to one “PIN” only, to stop any linking, ie. operative action.

Plug-in radio receiver card type “Jubi 433/2 R” fitted with stabilized resonator, complete with two relay modules for channels 1 and 2, 433.92 MHz.

Dis. N. 4047

Via Mantova, 177/A – C.P. 126 – 37053 Cerea (Verona) Italy – Tel. +39 0442 330422 r.a. ® Fax +39 0442 331054 – e-mail: info@fadini.net – www.fadini.net

F a) CONNAITRE LA MEMOIRE LIBRE -P1-

DESCRIPTION DES COMPOSANTS Fig.1

Pour connaître la mémoire libre dans le récepteur radio il faut qu’il soit alimenté et enficher le cavalier “STRIP” sur la position “P1”. Ensuite en appuyant sur le bouton-poussoir “P”, on obtient au bout de 5 secondes un ou plusieurs clignotements de la “LED”. Chaque clignotement correspond à 25 émetteurs. b) EFFACER TOTALEMENT LA MEMOIRE -P2-
Pour effacer totalement la mémoire d’un récepteur, et donc tous les émetteurs enregistrés, il faut que la carte soit alimentée en 24 Volts. Vous devez ensuite insérer le cavalier “STRIP” sur la position “P2” et actionner le poussoir “P” durant 5 secondes, puis le relâcher. Un moment après, la led de signalisation

1 – Memoire enfichable 2 – Poussoir “P” 3 – Cavalier “STRIP” 4 – Ponts 1ère et 2ème canal: choisir le poussoir
émetteur de 1 à 4 max. 5 – Led 6 – Relais pour actionner le 2ème canal

èmettra une impulsion lumineuse qui indiquera que l’opération d’effacement est terminée. c) MEMORISATION 1ère CANAL -1-
Pour rentrer le 1ère canal, il faut d’abord mettre le cavalier “STRIP” sur la position “1”; puis appuyer simultanement sur le poussoir “P” du récepteur et une touche de l’émetteur durant 5 secondes. Lorsque le code est enrégistré le voyant “LED” s’allume pour confirmer la prise en compte du code. d) MEMORISATION 2ème CANAL -2Pour rentrer le 2ème canal procéder de la même façon que ci-dessus en mettant le cavalier “STRIP” sur la position “2”.

7 – Borne de raccordement 2ème canal contact N.F. et N.O. et antenne
8 – Connecteur enfichable femelle 1ère canal et alimentation 24 V
9 – Relais pour actionner le 1ère canal 10 – Programmateur électronique série Elpro 11 – Connecteur enfichable mâle

NOTE: Aprés les opérations a,b,c,d, il est important d’enlever le cavalier “STRIP” et le mettre sur un

seul “PICOT”, pour éviter des contacts.

Carte enfichable pour récepteur radio “Jubi 433/2 R” avec résonateur stabilisé complet de deux modules relais pour le 1ère et 2ème canal fréquence 433,92 MHz.

D a) PRÜFEN WIEVIEL PLATZ IM SPEICHER FREI IST -P1-

BESCHREIBUNG DER BESTANDTEILEN Abb.1

Um zu erfahren wieviel Platz in dem Speicher des Empfängers noch vorhanden ist, muss man 1 – Abnehmbarer Speicher

bei mit 24 Volt gespeistem Modul die “STRIP” Codierbrücke in die Position “P1” einfügen und 2 – Schalter “P”

die Taste “P” 5 Sekunden lang drücken: lässt man die Taste los, so kann man ein Blinken erkennen. Jedem Blinken des LEDs entsprechen 25 Handsender, die noch gespeichert werden können. b) KOMPLETTES LÖSCHEN DES SPEICHERS -P2-
Um den gesamten codierten Speicher auf dem Funkempfänger zu löschen, den “STRIP” Codier-brücke in Position “P2” stecken, wobei die Platine immer mit 24 Volt versorgt wird. Die Taste “P” muss 5 Sekunden lang gedrückt werden, danach lässt man sie los, in diesem Moment sendet das LED einen

3 – “STRIP” Codierbrücke 4 – 1.-2. Kanal Anschlüsse: Wahl des
Sendersauslösers von 1 bis 4 max. 5 – Led 6 – Relais zur Steuerung des 2. Kanals

Lichtimpuls, der anzeigt, dass der Löschvorgang erfolgt ist.

7 – Klemme 2. Kanal N.C. und N.O. Anschluss

c) EINGABE 1. KANAL -1-

und Antenne (Klemmen 1-2)

Um den 1. Kanal zu codieren, die “STRIP” Brücke in die Position “1” stecken, danach gleichzeitig die 8 – Einsteckverbinder Mutter des 1. Kanals und

Taste “P” und eine Taste des Handsenders (nach Wahl) ungefähr 5 Sekunden lang drücken. Dadurch wird die LED Signalleuchte aufleuchten, wodurch uns die erfolgte Einspeicherung des Codes bestätigt wird. d) EINGABE 2. KANAL -2Um dem 2. Kanal zu kodieren, wie oben Position “c” beschrieben vorgehen, die einzige Unterschied

24 V Speisung 9 – Relais zur Steuerung des 1. Kanals 10 – Elektronische Steuerung Serie Elpro 11 – Einsteckverbinder Zapfen

ist, dass die “STRIP” Brücke in die Position “2” gesteckt wird.

NB: Nachdem man die Test a,b,c,d durchgeführt hat, die “STRIP” Codierbrücke entfernen und sie in einen einzigen “PIN” stecken, damit er keinen Kontakt

mehr macht.

Einsteck-Empfänger “Jubi 433/2 R” mit stabilisiertem Resonator komplett mit zwei Relaismodulen für den 1. und 2. Kanal, Frequenz 433,92 MHz.

E a) PARA CONOCER LA MEMORIA LIBRE -P1-

DESCRIPCION COMPONENTES Fig.1

Para averiguar cuanta memoria está disponible en el radiorreceptor, siempre estando la ficha alimentada a 24 Voltios, hay que conectar el puente “STRIP” en la posición “P1” y apretar el pulsador “P” durante 5 segundos: soltandolo se pueden observan unos relampagueos. Cada relampagueo de led señala que hay 25 transmisores que pueden memorizarse aun. b) BORRADURA TOTAL DE LA MEMORIA -P2-
Se borra toda la memoria codificada en el receptor colocando el “STRIP” como un puente en la posición “P2”, siempre estando alimentada la ficha misma a 24 Voltios. Se aprieta el pulsador “P” durante 5 segundos, se le suelta y en aquel momento el led emite un impulso luminoso, que señala que la operación

1 – Memoria amovible 2 – Pulsador “P” 3 – Pieza de contacto “STRIP” puentes 4 – Puentes 1er y 2° canal: eleccion desde 2 hasta
4 pulsadores del transmisor 5 – Led 6 – Relé para activar el 2° canal

de borradura se ha realizado.

7 – Borne de conexion 2° canal contacto N.C.-N.A.

c) CODIFICACION 1er CANAL -1Para codificar el 1er canal, colocar ante todo el “STRIP” en la posición “1”; a continuación, apretar al mismo tiempo durante 5 segundos el pulsador “P” e una tecla a elección del transmisor. El led emitirá después una impulsión de luz para confirmar que el código ha sido memorizado.
d) CODIFICACION 2° CANAL -2Para codificar el 2° canal, actuar como reseñado en el apartado “c” excepto únicamente que se coloca el “STRIP” en la posición “2”.

y antena (borne 1-2) 8 – Conectador enchufable hembra 1er canal y
suministro de corriente 24 V 9 – Relé para activar el 1er canal 10 – Programador electronico serie Elpro 11 – Conectador enchufable macho

NOTA: es importante que al final de los ensayos a,b,c,d se quiete el puente “STRIP” y se lo introduzca

en un sólo “PIN”, de forma que el mismo no haga más contacto.

Ficha enchufable radiorreceptor “Jubi 433/2 R” con resonador estabilizado de cuarzo, equipada de dos módulos relés para el 1er y el 2° canal, frequencia 433,92 MHz.

BESCHRIJVING ONDERDELEN (FIG.1)
1 – Uitneembaar geheugen 2 – Drukknop “P” 3 – Inzetcontact “STRIP” geleiderbruggen 4 – Geleiderbruggen 1e-2e kanaal: keuze
uit 1 tot 4 drukknoppen van de zender

Om het geheugen in de ontvanger te annuleren, met de kaart met een stroomtoevoer van 24 Volt, moet de “STRIP” geleiderbrug op positie “P2” worden ingestoken en moet drukknop “P” gedurende vijf

5 – Led 6 – Relais om het 2e kanaal te activeren

seconden worden ingedrukt; hierna moet deze worden losgelaten en zal de lichtdiode op dat moment 7 – Verbindingsklem 2e kanaal normaal geopend,

een lichtsignaal afgeven: dit geeft aan dat de annuleringshandeling is uigevoerd. c) CODERING 1e KANAAL -1-
Om het 1e kanaal te coderen moet de “STRIP” aanvankelijk op positie “1” worden ingesteld: daarna moet men tegelijkertijd gedurende vijf seconden drukknop “P” drukken en een toets van de zender naar keuze indrukken. De lichtdiode zal hierna een verklikkersimpuls afgegeven ter bevestiging dat de code in het. d) CODERING 2e KANAAL -2-

normaal gesloten contact en antenne (1-2) 8 – Vrouwtjes-koppelingsconnector 1e kanaal en
stroomtoevoer van 24 Volt 9 – Relais om het 1e kanaal te activeren 10 – Elektronische programmeereenheid Elpro serie

Om het 2e kanaal te coderen moet men handelen zoals in punt “c” is beschreven met het enige verschil 11 – Mannetjes-koppelingsconnector

dat de “STRIP” op positie “2” moet worden ingesteld.

OPMERKING: Het is belangrijk dat na test a,b,c,d de “STRIP” geleiderbrug wordt weggenomen en dat

men deze in één “PIN” steekt zodat deze geen contact meer tot stand brengt.

Koppelingskaart ontvangstradio “Jubi 433/2 R” met gestabiliseerde kwartsresonator, compleet met twee relaismodules voor het 1e het 2e kanaal, frequentie 433,92 MHz.

Dis. N. 4047

Via Mantova, 177/A – C.P. 126 – 37053 Cerea (Verona) Italy – Tel. +39 0442 330422 r.a. ® Fax +39 0442 331054 – e-mail: info@fadini.net – www.fadini.net

ENCODING INSTRUCTIONS
RADIO TRANSM ITTER JUBI· 433
GB

®
the gate opener

RADIO RECEIVER EXTERNAL TYPE. ENCODING INSTRUCTIONS AND W ORKING PRINCIPLE

Drw g. No. 3706
RECEIVER FOR EXTERNAL APPLICATION

SW ITCH BUTTON ” P”

REM OVABLE

LED

M EM ORY

” STRIP” JUM PER PIN

LED 2nd PUSH BUTTON

1st PUSH BUTTON

TRANSM ITTER J UB I · 433 4 CHANNELS

24 V a.c. POW ER SUPPLY
CHANNEL 1 CHANNEL 2 CHANNEL 3 CHANNEL 4

AERIAL

TRANSM ITTER JUBI-SM ALL·433 2 CHANNELS

ANY BUTTON IN THE TRANSM ITTER CAN BE PRESSED TO OPERTE ANY REQUIRED CHANNEL, PROVIDED THAT THE ” STRIP” IS INSERTED IN THE PROPER ” PIN” CONNECTORS THAT CORRESPOND TO THE DESIRED CHANNEL. ENCODE THE UNIT AS DESCRIBED.
The instructions that follow explain how to set a personalized code (ie. user’s code) w ith any one receiver. First supply 24 Volt a.c. pow er to terminals 1 () and 2 (+) in the receiver terminal board – then insert the ” STRIP” as in position ” C1″ . This activates the relay ” 1R” that corresponds to terminals 3 and 4 (CHANNEL No. 1). The next step is to press simultaneously the sw itch button ” P” on the receiver PC board and the sw itch button ” T” (any desired one) on the transmitter for about five seconds. Once the code has been memorized by the unit, the ” LED” on the receiver PC board sw itches on. Release the transmitter button and the receiver sw itch button; remove the ” STRIP” jumper and insert it on to a ” PIN” connector on standby. Now the radio remote control set has been encoded w ith a personalized, secret code and is ready to w ork. Repeat the above sequence for channels 2-3-4. Insert the ” STRIP” jumper in the correct position as required, as follow s:
Position ” C2″ . It corresponds to relay No. 2 (2R) – Channel No. 2. – Terminals 5-6 Position ” C3″ . It corresponds to relay No. 3 (3R) – Channel No. 3. – Terminals 7-8 Position ” C4″ . It corresponds to relay No. 4 (4R) – Channel No. 4. – Terminals 9-10 SHOULD THE POW ER SUPPLY FAIL OR THE 24 V a.c. – 12 Vd.c. BE DISCONNECTED FROM THE RECEIVER, THE USER’S CODE IS RETAINED IN THE REM OVABLE M EM ORY THAT CAN BE FITTED ON TO ANOTHER CARD.

TECHNICAL SPECIFICATIONS. RADIO RECEIVER EXTERNAL TYPE AND TRANSM ITTER

Drw g. No. 3707
PIN COM BINATIONS
FREE M EM ORY TOTAL M EM ORY REM OVAL Relay 1 Relay 2

RADIO RECEIVER FOR EXTERNAL APPLICATION
SW ITCH BUTTON ” P”
REM OVABLE M EM ORY

TRANSM ITTER Jubi·433 – 4 CHANNELS 84x43x17 mm

Relay 3

” STRIP”

JUM PER

Relay 4

Jubi 433
433,92 MHz “Rolling-Code”
0678
Made in Italy

24 V a.c. POW ER SUPPLY
CHANNEL 1 CHANNEL 2
CHANNEL 3 CHANNEL 4

RADIO RECEIVER FOR EXTERNAL APPLICATION 60x52x1,6 mm

AERIAL TRANSM ITTER TECHNICAL SPECIFICATIONS

RADIO RECEIVER TECHNICAL SPECIFICATIONS Working frequency……………………………………………………………………………………………….433.92 M Hz Sensitivity (to operating pulse)……………………………………………………………………………………..> 1 uV Distance range ……………………………………………………………………………………………………..100 meters Pow er supply w ith alternated current………………………………………………………….24 Vac (+/ 10%) Pow er supply w ith direct current ……………………………………………………………12 Vdc (+ 20% 5%) Working absorption…………………………………………………………………25 mA (1st energized channel) Standby absorption ………………………………………………………………………………………………………10 mA Decrypt ……………………………………………………………………………………………………………………..DIGITAL No. of channels …………………………………………………………………………………………………………………….4 Changeover contact relay ……………………………N.O. (Channel 1) – N.O. or N.C. (Channels 2-3-4) Relay rating …………………………………………………………………………………………………….0,5 A 125 Vac Excitation time ……………………………………………………………………………….200 ms (1 complete code) Dropout time ……………………………………………………………………………..300 ms (from last valid code) Working temperature……………………………………………………………………………………….10° C + 55° C * Channel 1 module is factory fitted. Fit the other relay modules into the respective connectors for the remaining channels.

Working frequency……………………………………………………………………………………………….433.92 M Hz Carrier frequency tolerance …………………………………………………………………………………..+/75 KHz Radiated pow er ………………………………………………………………………………………………………….100 uW Band w idth ………………………………………………………………………………………………………………..>25 KHz Apparent pow er of the harmonic products ……………………………………………….<54 dBm (<4 uW ) Supply voltage ………………………………………………………………………………12 Vdc -23 A (+20% 50%) M ean absorption ………………………………………………………………………………………………………….14 mA Working temperature………………………………………………………………………………………….40°C +85°C No. of channels …………………………………………………………………………………………………………………….4 Distance range ……………………………………………………………………………………………………..120 meters Code type …………………………………………………………………DIGITAL (264 encrypted) ” Rolling-Code” · A radio signal is activated by pressing a button in the transmitter and stays on as long as
the button is kept dow n. A red led sw itches on to confirm the signal. · An electric contact is closed instantaneously on releasing the button and the unit becomes
operating. · Replace the 12V battery should the led flash on/off on pressing the button. · To achieve best performance of the aerial, make sure that the core and the braided w ire
of the coaxial cable are connected to their respective terminals as indicated. · Keep the transmitter aw ay from heat sources and handle it w ith care. · Dispose properly of run dow n batteries.

SHOULD THE POW ER SUPPLY FAIL OR THE 24 V a.c. – 12 Vd.c. BE DISCONNECTED FROM THE RECEIVER, THE USER’S CODE IS RETAINED IN THE REM OVABLE M EM ORY THAT CAN BE FITTED ON TO ANOTHER CARD.
3

SELF-LEARNING PLUG-IN CARD. ENCODING INSTRUCTIONS AND W ORKING PRINCIPLE

Drw g. No. 3751

PLUG-IN RADIO RECEIVER CARD

REM OVABLE

SW ITCH BUTTON ” P”

LED

” STRIP”

M EM ORY

JUM PER

PIN PLUG-IN CON N ECTOR

2nd PUSH BUTTON

LED 1st PUSH BUTTON

TRANSM ITTER J UB I · 433 4 CHANNELS

TRANSM ITTER JUBI-SM ALL·433 2 CHANNELS

CHANNEL 1

+ ~24 V
ELECTRON I C CONTROL PANEL TYPE ELPRO POW ER SUPPLY 230 V

ANY BUTTON IN THE TRANSM ITTER CAN BE SELECTED TO OPERATE ANY REQUIRED CHANNEL. INSERT THE JUM PER IN THE DESIRED POSITION. ENCODE THE UNIT AS DESCRIBED.
How to set a personalized code (ie. user’s code) w ith a plug-in type receiver card. First supply it w ith pow er by plugging it into an operating control box. Then insert the ” STRIP” jumper as in position ” C1″ . This activates the relay ” 1R” that is directly connected to the respective circuit in the control panel. The next step is to press simultaneously the sw itch button ” P” on the receiver card and a push button (any desired one) on the transmitter for about five seconds. Once the code has been memorized by the unit, the led on the receiver card sw itches on. Release the transmitter button and receiver sw itch button; remove the ” STRIP” jumper and insert it on to one ” PIN” only. Now the radio remote control set has been encoded w ith a personalized secret code and is ready to w ork. Repeat the above sequence to encode channel No. 2, w hich provides an extra output for user’s personal applications, but the jumper must be inserted in position ” C2″ to activate the second relay ” 2R” through another transmitter button. The connection to output for channel 2 can either be normally open or closed (N.O. – N.C.) to meet all possible applications.

SHOULD THE POW ER SUPPLY FAIL OR THE 24 V a.c. – 12 Vd.c. BE DISCONNECTED FROM THE RECEIVER, THE USER’S CODE IS RETAINED IN THE REM OVABLE M EM ORY THAT CAN BE FITTED ON TO ANOTHER CARD.

TECHNICAL SPECIFICATIONS. PLUG-IN RADIO RECEIVER AND TRANSM ITTER

Drw g. No. 3702

PLUG-IN RADIO RECEIVER 56x43x1,6 mm

TRANSM ITTER Jubi-Small· 433, 2 CHANNELS, 40x48x14 mm

PIN COM BINATIONS

TOTAL M EM ORY REM OVAL

FREE M EM ORY

Relay 2 (C2)

Relay 1 (C1)

SW ITCH BUTTON ” P”
REM OVABLE M EM ORY

” STRIP” JUM PER

Jubi Small 433

433,92 MHz “Rolling-Code”

0678

Made in Italy

PLUG-IN CONNECTOR
PLUG-IN RADIO RECEIVER TECHNICAL SPECIFICATIONS
Working frequency……………………………………………………………………………………………….433.92 M Hz Sensitivity (to operating pulse)……………………………………………………………………………………..> 1 uV Distance range ……………………………………………………………………………………………………..100 meters Pow er supply w ith alternated current………………………………………………………….24 Vac (+/ 10%) Pow er supply w ith direct current ……………………………………………………………12 Vdc (+ 20% 5%) Working absorption…………………………………………………………………25 mA (1st energized channel) Standby absorption ………………………………………………………………………………………………………10 mA Decrypt ……………………………………………………………………………………………………………………..DIGITAL No. of channels …………………………………………………………………………………………………………………….2 Changeover contact relay ……………………………………N.O. (Channel 1) – N.O. or N.C. (Channel 2) Relay rating …………………………………………………………………………………………………….0.5 A 125 Vac Excitation time ……………………………………………………………………………….200 ms (1 complete code) Dropout time ……………………………………………………………………………..300 ms (from last valid code) Working temperature……………………………………………………………………………………….10° C + 55° C

TRANSM ITTER TECHNICAL SPECIFICATIONS
Working frequency……………………………………………………………………………………………….433.92 M Hz Carrier frequency tolerance …………………………………………………………………………………..+/75 KHz Radiated pow er ………………………………………………………………………………………………………….100 uW Band w idth ………………………………………………………………………………………………………………..>25 KHz Apparent pow er of the harmonic products ……………………………………………….<54 dBm (<4 uW ) Supply voltage ………………………………………………………………………………12 Vdc -23 A (+20% 50%) M ean absorption ………………………………………………………………………………………………………….12 mA Working temperature………………………………………………………………………………………….40°C +85°C No. of channels …………………………………………………………………………………………………………………….2 Distance range ……………………………………………………………………………………………………..120 meters Code type …………………………………………………………………DIGITAL (264 encrypted) ” Rolling-Code”
· A radio signal is activated by pressing a button in the transmitter and stays on as long as the button is kept dow n. A red led sw itches on to confirm the signal.
· An electric contact is closed instantaneously on releasing the button and the unit becomes operating.
· Replace the 12V battery should the led flash on/off on pressing the button. · To achieve best performance of the aerial, make sure that the core and the braided w ire
of the coaxial cable are connected to their respective terminals as indicated. · Keep the transmitter aw ay from heat sources and handle it w ith care. · Dispose properly of run dow n batteries.

SHOULD THE POW ER SUPPLY FAIL OR THE 24 V a.c. – 12 Vd.c. BE DISCONNECTED FROM THE RECEIVER, THE USER’S CODE IS RETAINED IN THE REM OVABLE M EM ORY THAT CAN BE FITTED ON TO ANOTHER CARD.
5

TO STORE OTHER TRANSM ITTER CODES INTO THE SAM E RECEIVER M EM ORY

RECEIVER ALREADY CON N ECTED

POW ER SUPPLY ~24 VOLT a.c.

(No. 1-2)

1st CHANNEL (No. 3-4)

HOW TO DUPLICATE OR ENCODE NEW TRANSM ITTERS, WHICH ARE TO OPERATE THE SAM E RECEIVER. IT IS REQUIRED TO PERFORM TW O OPERATIONS IN A SEQUENCE, AND A PREVIOUSLY ENCODED TRANSM ITTER M UST BE AVAILABLE. EN CODIN G OPERATION S ARE TO BE PERFORM ED AT A RECOM M EN DED DISTANCE, ie. 10 TO 20 M ETRES FROM THE OPERATIVE RECEIVER AND ARIAL.

1st OPERATION A new transmitter ” A” (blank, ie. not previously encoded) is available. Press any tw o buttons simultaneously for 10 seconds. Release the buttons and carry on the 2nd operation w ithin 15 seconds.

2nd OPERATION

Transmitter ” B” (previously enc oded) is available; Press tw o buttons

B (corresponding to those in transmitter ” A” ) simultaneously for 10 seconds.
Once the buttons are released, the receiver can read the code from the new

transmitter when this is used.

THE ABOVE SEQUENCE OF OPERATIONS IS TO BE REPEATED W ITH EACH NEW TRANSM ITTER THAT IS REQUIRED TO BE USED ALONG W ITH THE EXISTING ON ES.

B LA N K TRANSM ITTER 6

W HEN TW O B UTTON S A RE PRESSED SIM ULTA N EOUSLY N O RELAY IS ACTIVATED.

AERIAL PREVIOUSLY ENCODED TRANSM ITTER

HOW TO ERASE A TRANSM ITTER CODE FROM A RECEIVER

TRANSM ITTER Jubi-Small· 433, 2 CHANNELS

TRANSM ITTER Jubi· 433, 4 CHANNELS

STAND ALONE RADIO RECEIVER CARD

1st Sequence TW O buttons 10 sec. TIM E

” STRIP” JUM PER

2nd Sequence ONE button

24 V a.c. POW ER SUPPLY

AERIAL

PLUG-IN RADIO RECEIVER CARD ” STRIP” JUM PER

CHANNEL 1 CHANNEL 2
CHANNEL 3 CHANNEL 4

3rd Sequence TW O buttons 4th Sequence ONE button 5th SequenceTW O buttons

THIS EXPLAIN S HOW TO ERASE A TRAN SM ITTER CODE FROM A RECEIVER. ALTERNATING OPERATIONS ARE TO BE PERFORM ED IN A SEQUENCE W ITH THE SAM E TRANSM ITTER. RECOM M ENDED DISTANCE FROM THE OPERATIVE RECEIVER AND AERIAL IS 10 TO 20 M ETRES.
Operative sequence Insert the jumper ” STRIP” as in position ” P1″ (if not already pre-set) 1st Operation. Press tw o buttons on the transmitter simultaneously. Release the
buttons. Proceed to the 2nd operation. 2nd Operation. Press one button only (as in the picture), then release it and proceed
to the 3rd operation, ie. press again the tw o buttons simultaneously. In other w ords you repeat the first tw o operations alternately 5 times in total, as in the picture. The limit time betw een one operation and the other is 10 seconds.
SHOULD IT BE REQUIRED TO ERASE SEVERAL TRANSM ITTER CODES, THE ABOVE SEQUEN CE M UST BE PERFORM ED IN DIVIDUALLY FOR EACH TRAN SM ITTER.

SHOULD YOU FAIL TO COUNT THE OPERATIONS IN THE CORRECT SEQUENCE OR PRESS THE W RONG BUTTONS, YOU HAVE TO START FROM THE BEGINNING. WAIT ONE M INUTE BEFORE REPEATING THE SEQUENCE. M AKE SURE THAT THE RECEIVER HAS VOLTAGE.
7

FREE M EM ORY M ONITORING P1 Jubi· 433 “ROLLING-CODE”

RADIO RECEIVER Jubi· 433 EXTERNAL USE – 4 CHANNELS STABILIZED RESONATOR, 433.92 M Hz, SELF LEARNING, “ROLLING-CODE”

REM OVABLE M EM ORY

SW ITCH
BUTTON ” P”

RADIO RECEIVER Jubi· 433 PLUG-IN TYPE – 2 CHANNELS STABILIZED RESONATOR, 433.92 M Hz, SELF LEARNING, “ROLLING-CODE”

SW ITCH
BUTTON ” P”
REM OVABLE M EM ORY

” STRIP” CODIERBRÜCKE

” STRIP” JUM PER

” STRIP” JUM PER PIN

PIN PLUG-IN CON N ECTOR

24 V a.c. POW ER SUPPLY
CHANNEL 1 CHANNEL 2
CHANNEL 3 CHANNEL 4

AERIAL

Jubi 433 433,92 MHz RESONATOR STABILISIERT “Rolling-Code”
+
M onitoring the free portion, ie. storage availability in the receiver memory. 24 Volt pow er supply still connected to the unit. Insert the ” STRIP” jumper as in position ” P1″ (PIN) and press the button sw itch ” P” for 5 seconds: after releasing it, a number of flashes can be noted. Each flash of light through the ” LED” corresponds to 25 transmitters that can be still encoded and stored in the memory. – Example: 7 flashes of light can be counted. It means: 25 still available codes times 7, ie. the No. of the flashes is equal to 175, ie. the number of transmitters that can still be encoded and stored. Once the test is finished, remove the ” STRIP” and put it on to one pin only to stop any linking, ie. operative action.
FOR ENCODING AND STORING OPERATIONS W ITH OTHER TRASM ITTERS FOLLOW THE INSTRUCTIONS ON DRAW. 3706 – 3751. 8

TOTAL M EM ORY REM OVAL P2 Jubi· 433 “ROLLING-CODE”

RADIO RECEIVER Jubi· 433 EXTERNAL USE – 4 CHANNELS STABILIZED RESONATOR, 433.92 M Hz, SELF LEARNING, “ROLLING-CODE”

REM OVABLE M EM ORY

SW ITCH
BUTTON ” P”

RADIO RECEIVER Jubi· 433 PLUG-IN TYPE – 2 CHANNELS STABILIZED RESONATOR, 433.92 M Hz, SELF LEARNING, “ROLLING-CODE”

SW ITCH
BUTTON ” P”
REM OVABLE M EM ORY

” STRIP” CODIERBRÜCKE

” STRIP” JUM PER

” STRIP” JUM PER PIN

PIN PLUG-IN CON N ECTOR

AERIAL

24 V a.c. POW ER SUPPLY
CHANNEL 1 CHANNEL 2
CHANNEL 3 CHANNEL 4

Jubi 433 433,92 MHz RESONATOR STABILISIERT “Rolling-Code”
+
To perform the total removal of the receiver encoded memory, position the ” STRIP” as in “P2”, the receiver still under 24 V a.c. – 12 Vd.c. voltage supply. Press the sw itch button “P” for 5 seconds, then release it. The led flashes once to confirm that the removal operation has been carried out completely. Remove the ” STRIP” and position it on to one ” PIN” only to prevent any operative action. TO ENCODE NEW AND EXISTING TRANSM ITTERS AND STORE THEIR CODES ANEW IN THE RECEIVER M EM ORY KEEP TO THE INSTRUCTIONS ON DRAW. 3706 – 3751.

M ATERIAL ABS = B70 SINKRAL

Jubi· 433 – 4 CHANNELS COLOUR: M ETAL BLACK
NIGHT BLUE BUTTONS ROUND LENS TRANSM ITTER COVER FOUR BUTTON ARRAY
TRANSM ITTER ELECTRONIC CARD TRANSM ITTER CASING 12 Vd.c. 23 A (+ 20% 50%) BATTERY BATTERY BRACKET FIXING SCREW

Jubi-Small· 433 – 2 CHANNELS COLOUR: NIGHT BLUE
LILY-SHAPED TRANSPARENT LENS TRANSM ITTER COVER TRANSM ITTER CASING TRANSM ITTER ELECTRONIC CARD BATTERY BRACKET 12 Vd.c. 23 A (+ 20% 50%) BATTERY FIXING SCREW

76 84 73 48 43 210

OVERALL DIM ENSIONS
43

17 4 CHANNELS

Jubi 433
433,92 MHz “Rolling-Code”
0678
Made in Italy

27
91 RADIO RECEIVER EXTERNAL TYPE Jubi·433 – 4 CHANNELS

2 CHANNELS

PLUG-IN CARD TYPE Jubi·433 – 2 CHANNELS

Jubi Small 433

433,92 MHz “Rolling-Code”

0678

Made in Italy

68 11

10-2003 Lineagrafica

®
M ade in Italy
® s.n.c.
AU TO M AT I C GAT E M AN U FACT U RERS
Via M antova, 177/A – 37053 Cerea (Verona) Italy – Tel. 0442 330422 r.a. – Fax 0442 331054 – e- mail: info@fadini.net – w w w .fadini.net

Documents / Resources

FADINI Jubi 433 4 Button Radio Transmitter [pdf] Instruction Manual
Jubi 433, Jubi 433 4 Button Radio Transmitter, 4 Button Radio Transmitter, Radio Transmitter, Transmitter

References

User Manual

FADINI Jubi 433 4 Button Radio Transmitter Instruction Manual

Jubi 433 4 Button Radio Transmitter

Specifications:

Product Usage Instructions:

I. Free Memory Monitoring (P1)

II. Total Memory Removal (P2)

III. Encoding Channels

Frequently Asked Questions (FAQ):

Q: How do I know if the encoding process was successful?

Q: Can I encode multiple transmitters for a single
channel?

Documents / Resources

References

Leave a comment

Cancel reply