1. مقدمه
The FLSUN S1 Pro is an advanced FDM Delta 3D printer designed for high-speed and high-precision additive manufacturing. It features an ultra-fast printing speed of up to 1200mm/s and an acceleration of 40,000mm/s², significantly reducing print times. Equipped with Klipper firmware, a 7-inch smart touch screen, and a 350℃ all-metal hotend, the S1 Pro supports a wide range of filaments, including high-performance engineering materials. Its large build volume of Φ320*320*430 mm³ accommodates substantial projects. This manual provides essential information for setting up, operating, maintaining, and troubleshooting your FLSUN S1 Pro 3D Printer.
تصویر 1.1: جلو view of the FLSUN S1 Pro 3D Printer, showcasing its sleek design and enclosed build chamber.
۲. چه چیزهایی در جعبه است؟
هنگام باز کردن بستهبندی، لطفاً بررسی کنید که همه اجزا وجود دارند:
- FLSUN S1 Pro 3D Printer (main unit)
- جعبه خشک کن رشته ای
- کابل برق
- کابل USB
- جعبه ابزار (انواع آچار، پیچگوشتی و...)
- Sampفیلامنت
- راهنمای کاربر (این سند)
- راهنمای شروع سریع
Image 2.1: The FLSUN S1 Pro 3D Printer and its included accessories, demonstrating its 95% pre-assembled state.
۱. دستورالعملهای راهاندازی
The FLSUN S1 Pro is designed for quick setup, being 95% pre-assembled. The initial setup typically takes less than 10 minutes.
- باز کردن بسته بندی: چاپگر و تمام لوازم جانبی را با دقت از بستهبندی خارج کنید.
- قرار دادن: چاپگر را روی یک سطح صاف و پایدار در یک محیط با تهویه مناسب قرار دهید.
- مونتاژ: Install the door and glass panels as per the instructions in the detailed دفترچه راهنمای نصب (PDF).
- اتصال برق: Connect the power cable to the printer and a suitable power outlet.
- روشن شدن اولیه: Turn on the printer using the main power switch. The device will perform self-checks to ensure stability.
- تسطیح خودکار: The printer features automatic leveling. Follow the on-screen prompts on the 7-inch touch screen to initiate and complete the leveling process. This ensures optimal print bed calibration.
- بارگذاری رشته: Load your desired filament into the filament dryer box and then guide it into the extruder as instructed on the display.
- اتصال شبکه: Connect the printer to your local Wi-Fi network via the touch screen interface for remote monitoring and control.
برای دستورالعملهای بصری دقیق، لطفاً به مرجع رسمی مراجعه کنید دفترچه راهنمای نصب (PDF).
4. دستورالعمل های عملیاتی
۴.۱ رابط کاربری و کنترل
The FLSUN S1 Pro utilizes a 7-inch Klipper firmware smart touch screen for intuitive control. The visual operation interface allows for smart adjustment and monitoring directly from the printer. Additionally, with advanced Microtac radar control and Wi-Fi connectivity, you can monitor and control your printer in real-time from mobile phones and PCs.
Image 4.1: Remote control and monitoring capabilities via the FLSUN World app on a mobile device.
- کنترل از راه دور: Manage your printers remotely from anywhere.
- Tap it, Print it, Like it: Start printing tasks with a quick tap on the FLSUN World app, utilizing cloud storage for G-code files.
- Monitor in Pocket: Real-time checking of your printing progress.
- Smart Reminder: Receive notifications when print errors occur.
۶.۳ فرآیند چاپ
- آماده سازی مدل: Use compatible slicing software (FLSUN Slicer V2.0 or other slicers like PrusaSlicer, Cura) to prepare your 3D model. Ensure settings are optimized for the S1 Pro's capabilities, including its high speed and acceleration.
- انتقال File: کد G برش خورده را منتقل کنید file to the printer via USB or Wi-Fi (FLSUN World app).
- شروع چاپ: را انتخاب کنید file on the touch screen or through the app and initiate the print.
- نظارت: Utilize the built-in camera for real-time monitoring and time-lapse recording. The printer's low noise level (55dB) ensures a quiet operating environment.
- Power-Off Resume: In case of power interruption, the printer supports power-off continuous printing, resuming from where it left off. Vibration compensation further ensures print quality.
Image 4.2: Illustration of the FLSUN S1 Pro's epic speed capabilities: 1200mm/s max printing speed, 40000mm/s² max acceleration, and 110mm³/s peak flow rate.
Image 4.3: Key features for smooth and consistent printing, including AI-powered functions, auto-leveling, spaghetti detection, and perfect first layer adhesion.
Image 4.4: Advanced features like the Air Filter, Filament Dryer, Built-in camera, Intelligent Zoned Heating, and 16GB EMMC storage.
5. تعمیر و نگهداری
Regular maintenance ensures the longevity and optimal performance of your FLSUN S1 Pro 3D Printer.
- تمیز کردن: Regularly clean the print bed, nozzle, and internal components to prevent debris buildup. Use a soft cloth and appropriate cleaning solutions.
- فیلتر هوا: The printer is equipped with a combined HEPA + activated carbon air filter. Check and replace the filter periodically as needed to maintain air quality and prevent odors.
- Filament Dryer Box: Ensure the filament dryer box is functioning correctly to keep your filament dry, which is crucial for print quality.
- بازرسی نازل: Periodically inspect the 0.4mm hardened steel nozzle for wear or clogs. Replace if necessary. The all-metal hot end can reach up to 350°C, supporting various high-temperature filaments.
- روغن کاری: Refer to the detailed manual for any lubrication requirements for moving parts.
Image 5.1: Diagram illustrating the 350°C hotend, 50°C chamber, and 120°C hot bed for optimal material handling.
6 عیب یابی
این بخش به مشکلات رایجی که ممکن است در حین کار با آنها مواجه شوید، میپردازد.
| مشکل | علت احتمالی | راه حل |
|---|---|---|
| Print Not Sticking to Bed | Improper bed leveling, dirty print surface, incorrect bed temperature. | Re-run auto-leveling. Clean the print surface with isopropyl alcohol. Adjust hot bed temperature according to filament type (Max 120°C). |
| Filament Clogging | Dust in filament, incorrect hotend temperature, worn nozzle, heat creep. | Ensure filament is dry (use filament dryer). Verify hotend temperature (Max 350°C). Clean or replace nozzle. Check cooling fan operation. |
| "Spaghetti" Prints | Poor bed adhesion, model detaching, extrusion issues. | The S1 Pro features تشخیص اسپاگتی. Ensure proper bed adhesion. Monitor print progress via the built-in camera. |
| چاپگر پاسخ نمیدهد | Software glitch, loose connection, power issue. | Restart the printer. Check all cable connections. Ensure stable power supply. |
| کیفیت چاپ ضعیف | Incorrect slicing settings, worn nozzle, vibration, wet filament. | Optimize slicing parameters. Replace nozzle if worn. The printer has جبران ارتعاش; ensure it's active. Use filament dryer. |
Image 6.1: Features like the 55dB quiet fan and Power Off Resume Print (UPS) contribute to a reliable printing experience.
7. مشخصات فنی
| دسته بندی | مشخصات | جزئیات |
|---|---|---|
| ژنرال | حداکثر سرعت چاپ | 1200mm/s |
| حداکثر شتاب | 40000mm/s² | |
| اوج جریان | ۳۲ میلیمتر مکعب بر ثانیه | |
| حجم ساخت | Φ320*320*430 mm³ (Maximum height of the cylinder: 383mm) | |
| اتاق | بسته شد | |
| سطح نویز | 55 دسی بل | |
| سر ابزار | نازل | 0.4mm Hardened Steel Nozzle (supports various nozzle sizes) |
| Max Hot End Temp | 350 درجه سانتیگراد | |
| قطر رشته | 1.75 میلی متر | |
| رشته | فیلامنت پشتیبانی شده | Ideal: PLA, PETG, TPU. Satisfactory: ABS, ASA, PA, PC, PET. Capable: Carbon/Glass Fiber Reinforced PLA, PPS-CF, PPA-CF/GF. |
| Active Heating Dry Box | بله | |
| تشخیص گرفتگی رشته | بله | |
| گرما | صفحه ساخت | پلیت PEI بافتدار |
| Max Build Plate Temp | 120 درجه سانتیگراد | |
| گرمایش منطقه هوشمند | Inner Circle Ø220mm, Outer Ring 220-320mm | |
| الکترونیک | نمایش | 7" Color Touch Screen |
| ذخیره سازی | 16GB EMMC, 32GB USB Flash | |
| منبع تغذیه | 110-240 ولت، 50/60 هرتز | |
| مصرف برق در حالت روشن | 400 وات | |
| نرم افزار | ارتقاء سیستم عامل | OTA (Over-The-Air) |
| نرم افزار برش | FLSUN Slicer V2.0, Other Slicers | |
| سیستم عامل پشتیبانی شده | MacOS، ویندوز | |
| ویژگی ها | دوربین مانیتورینگ | Realtime, Timelapse |
| تشخیص رشته | بله | |
| جبران ارتعاش | بله | |
| شناسایی زباله | بله | |
| تشخیص اسپاگتی | بله | |
| Screen Auto Sleep | بله | |
| Printer Auto Power Off | بله | |
| سطح بندی خودکار | بله | |
| بازیابی اتلاف برق | Yes (Z lift, Backup Battery) | |
| فیلتر هوا | HEPA + Activated Carbon | |
| ابعاد فیزیکی | ابعاد محصول (D x W x H) | ۴.۷۲ اینچ عمق x ۱.۸۸ اینچ عرض x ۳.۳۴ اینچ ارتفاع (تقریباً ۱۲۰ میلیمتر x ۴۸ میلیمتر x ۸۵ میلیمتر) |
| Physical Dimension (Printer) | 550*596*1030 میلی متر | |
| وزن مورد | ۳.۷۴ پوند (تقریباً ۱.۷ کیلوگرم) | |
| رنگ | مشکی |
Image 7.1: Comprehensive technical specifications for the FLSUN S1 Pro 3D Printer.
8. گارانتی و پشتیبانی
FLSUN is committed to providing reliable products and excellent customer service.
- برمی گرداند: The product is eligible for 30-day easy returns. Please refer to the retailer's return policy for specific details.
- پشتیبانی مشتری: For technical assistance, troubleshooting, or warranty inquiries, please contact FLSUN Customer Support. You can often find support resources and contact information on the official FLSUN webسایت یا از طریق خرده فروشی که محصول از آن خریداری شده است.
- طرحهای حفاظتی: Extended protection plans, such as a 4-Year Protection Plan, may be available for purchase separately to provide additional coverage beyond the standard warranty.
- منابع آنلاین: بازدید کنید FLSUN Store on Amazon برای اطلاعات بیشتر در مورد محصول، سوالات متداول و پشتیبانی.
