Armstrong Flooring Alba Tan Peel and Stick Vinyl Tile Flooring Installation and Care Manual (Model AB009051)

1. محصول تمام شدview

This manual provides detailed instructions for the installation and care of Armstrong Flooring Alba Tan 2.6-mil x 12-in W x 12-in L Water Resistant Peel and Stick Vinyl Tile Flooring. These tiles offer effortless maintenance and exceptional performance, suitable for both high-traffic and high-moisture environments. Designed for durability and cost-effectiveness, the diverse range of designs, including Alba Tan, mirrors the elegance of natural stone, ceramic, and various patterns. Installation is designed to be straightforward, requiring no drying time for immediate use. The tiles are stain and scuff resistant, eliminating the need for buffing or polishing.

Image: Armstrong Flooring Alba Tan Peel and Stick Vinyl Tiles installed in a bathroom.

• نصب آسان: Peel and stick application with no drying time, allowing immediate use.
• کیفیت هوای داخل ساختمان: Certified by FloorScore to meet or exceed low-emission standards.
• Versatile Subfloors: Can be installed over concrete and wooden subfloors; on, above, or below grade.
• ابعاد: 2.6 mil thickness x 12-inch width x 12-inch length; each tile covers 1 square foot.

2. آماده سازی

2.1 Subfloor Requirements

Ensure your subfloor is clean, dry, level, and smooth before beginning installation. Proper subfloor preparation is crucial for optimal adhesion and longevity of the vinyl tiles.

2.2 Approved Installation Surfaces

Armstrong Flooring Peel and Stick Vinyl Tiles can be installed over the following existing surfaces:

• Existing Vinyl Flooring
• تخته سه لا
• بتن

2.3 Surfaces Not Approved for Installation

Do not install Armstrong Flooring Peel and Stick Vinyl Tiles over the following materials:

• تخته ذرات
• Waferboard
• Single-layer STURD-I Floor® panels
• Existing Vinyl Tile Below Grade (if not specifically approved)
• Existing Cushioned Vinyl Flooring
• فرش
• Strip Wood Flooring
• کفپوش پلانک

3. ابزار مورد نیاز

The following tools are needed for your peel and stick vinyl tile installation project:

• نوار اندازه گیری
• مداد
• خط گچ
• Carpenter's Square
• چاقوی کاربردی
• غلتک

4. مراحل نصب

A well-executed project begins with a well-thought-out plan of action. Follow these steps for successful installation:

4.1 Planning the Layout

1. Locate Wall Centers: Begin by locating the center of each wall in the room.
2. Strike Chalk Lines: Strike a chalk line at the center of the room, connecting the midpoints of opposite walls.
3. Divide into Quadrants: Measure the distance of the first chalk line and divide by two to find the center of the room. Using a carpenter's square at this marked center, snap another chalk line perpendicular to the first, dividing the room into four quadrants.
4. اجرای خشک: Perform a dry run by positioning your Armstrong Peel and Stick tiles in one quadrant of the room without removing the release paper. This helps map out the floor and tile placement.

4.2 Adjusting Layout for Edge Tiles

If edge tiles are less than half the tile width during your dry run, mark a new center line. For the best appearance, it is recommended to shift the center line of the room by half the width of the tile to ensure larger, more aesthetically pleasing cuts at the edges.

4.3 Tile Placement

1. Peel Release Paper: Peel the release paper off the backside of the tile.
2. Install from Center: Begin installing tiles at the center of the room, working one tile at a time, and one quadrant at a time.
3. فلش های جهت دار: Ensure all directional arrows on the back of the tiles face the same direction for a consistent pattern.
4. Butt Edges: Butt the edges of the tiles together tightly.
5. محکم فشار دهید: Press each tile firmly into place.

4.4 Final Rolling

After placing the tiles, use a roller to firmly roll the tiles to the subfloor in all directions. This ensures a strong bond and proper adhesion.

5. Cutting Tiles

۴.۳ ایجاد برش‌های مستقیم

To make a straight cut on your Armstrong Peel and Stick tile:

1. Place a full tile face up on top of the last full tile.
2. Place another full tile (Tile B) on top of Tile A, with its edge against the wall.
3. Using Tile B as a guide, draw a line with a pencil on the face of Tile A.
4. Cut Tile A along this line using a utility knife.

5.2 Cutting Around Obstacles

For cutting around obstacles such as pipes or irregular shapes:

1. Create a pattern first by drawing the outline of the obstacle onto a piece of paper or cardboard.
2. Trace this pattern onto the vinyl tile.
3. Carefully cut the tile according to the traced pattern using a utility knife, trimming as necessary to ensure a proper fit.

۴. مراقبت‌های پس از نصب

Once the entire peel and stick installation process is complete for your space, you can replace all wall base and molding.

مهم: Do not wash your new floor for five days following installation. This allows the adhesive to fully cure and ensures the longevity of your flooring, as per our warranty and care instructions.

7. مشخصات

8. گارانتی و پشتیبانی

For detailed warranty information, care instructions, and further support, please refer to the official Armstrong Flooring documentation included with your product or visit the Armstrong Flooring website. Adherence to installation and care guidelines is essential to maintain product warranty.