دفترچه راهنمای رطوبت سنج چوب و مصالح ساختمانی قلمی ANENG GN602

1. محصول تمام شدview

The ANENG GN602 is a portable, pen-type digital moisture meter designed for quick and accurate measurement of moisture content in various materials, including wood, lumber, concrete, bricks, and other building materials. Its compact design makes it suitable for woodworking, water damage restoration, construction, and home improvement projects.

ویژگی های کلیدی:

• Pen-Type Design: Convenient pocket-sized form factor for portability.
• پین‌های با دقت بالا: Equipped with two sensitive pins for swift and accurate readings.
• Dual Modes & 7 Calibration Scales: Offers two measurement modes and seven material calibration scales for diverse wood types and construction materials, covering a moisture range from 0.0% to 58%.
• تابع نگه داشتن داده: Allows retention of current readings for stable and precise recording.
• صفحه نمایش LCD با نور پس زمینه: وضوح خوانش‌ها را در شرایط نوری مختلف تضمین می‌کند.
• مصرف انرژی: Features automatic shutdown after 10 minutes of inactivity to conserve battery life.
• نشانگر کم بودن باتری: Displays an icon to remind users of timely battery replacement.

Figure 1: ANENG GN602 Pen-Type Moisture Meter with its protective cap removed, showing the measurement pins and the digital display. Two AAA batteries are shown alongside the device.

۵. راه‌اندازی و نصب باتری

Before using the ANENG GN602 moisture meter, ensure that the batteries are correctly installed.

2.1. نصب باتری

1. پوشش محفظه باتری را در پشت دستگاه پیدا کنید.
2. Open the cover by sliding or gently prying it off.
3. Insert two 1.5V AAA batteries, ensuring correct polarity (+/-) as indicated inside the compartment.
4. درپوش محفظه باتری را به طور ایمن تعویض کنید.

2.2. بررسی اولیه

After battery installation, power on the device. The display should illuminate. The meter features a self-check function built into the protective cap. To perform a self-check:

1. Ensure the protective cap is placed over the measurement pins.
2. Gently push the pins through the designated pin holes on the outer top of the cap.
3. The meter should display a reading of approximately 20.5% RH. If this reading is shown, the meter is calibrated correctly and ready for use.

Figure 2: The ANENG GN602 Moisture Meter illustrating its pen-type design and pocket-sized portability, along with a visual representation of its 7 material modes for different types of wood and building materials.

3. دستورالعمل های عملیاتی

3.1. روشن/خاموش

• را فشار دهید دکمه پاور برای روشن کردن کنتور
• The meter will automatically shut down after 10 minutes of inactivity to conserve battery life.

3.2. Selecting Material Mode

The meter offers 7 calibration scales (modes) for different materials. To select the appropriate mode:

• را فشار دهید دکمه‌ی «م» to cycle through the available material modes (Mode 1 to Mode 7).
• Refer to the user manual's material chart (not provided in this extract, but typically found in the full manual) to match the mode number with your specific material (e.g., oak, pine, concrete, brick).

Figure 3: The ANENG GN602 Moisture Meter shown in various application scenarios, including wood processing, plank processing, measuring firewood, and detecting moisture on a wall surface.

3.3. اندازه گیری

1. درپوش محافظ را از پین های اندازه گیری بردارید.
2. Select the appropriate material mode using the 'M' button.
3. Carefully insert the two measurement pins into the material you wish to test. Ensure both pins penetrate the surface adequately for an accurate reading.
4. The moisture content percentage روی صفحه LCD نمایش داده می شود.

۶. عملکرد نگهداری داده

• را فشار دهید 'MAX/MIN' button briefly to activate the data hold function. The current reading will be frozen on the display.
• Press the 'MAX/MIN' button again to release the hold and resume live measurements.
• Holding the 'MAX/MIN' button will display the maximum or minimum recorded values.

3.5. کنترل نور پس زمینه

• را فشار دهید دکمه روشن (often integrated with the power button or a separate button with a light bulb icon) to turn the LCD backlight on or off. This improves visibility in low-light conditions.

Figure 4: Comparison of the ANENG GN602 Moisture Meter's display with the backlight turned on (left) and off (right), demonstrating improved readability in darker environments.

4. تعمیر و نگهداری

• تمیز کردن: دستگاه را با یک پارچه خشک و نرم پاک کنید. از پاک کننده ها یا حلال های ساینده استفاده نکنید.
• ذخیره سازی: When not in use, always replace the protective cap over the measurement pins to prevent damage and injury. Store the device in a cool, dry place, away from direct sunlight and extreme temperatures.
• تعویض باتری: Replace batteries promptly when the low-battery indicator appears on the display to ensure accurate readings and prevent battery leakage.
• Pin Care: Ensure the measurement pins are clean and free from debris for optimal contact with the material.

5 عیب یابی

6. مشخصات

Figure 5: The ANENG GN602 Moisture Meter displayed with its packaging, showing key dimensions and battery type.

7. گارانتی و پشتیبانی

ANENG provides lifetime service and technical support for the GN602 moisture meter. For any inquiries, troubleshooting assistance, or warranty claims, please contact ANENG customer service through their official channels.

لطفا رسید خرید خود را برای استفاده از گارانتی نگه دارید.