SHARKOON Elite Shark CA300T Extended ATX PC Case User Manual

1. مقدمه

This manual provides comprehensive instructions for the SHARKOON Elite Shark CA300T Extended ATX PC Case. It covers the product's features, setup procedures, operational guidelines, maintenance tips, troubleshooting solutions, and detailed technical specifications. Please read this manual thoroughly before installation and use to ensure optimal performance and longevity of your PC case.

2. ویژگی های کلیدی

• طراحی آینده نگر: The CA300T features an expressive front panel with a geometric pattern, framed by brushed aluminum, giving it a distinctive and modern aesthetic.
• Advanced Airflow: Equipped with three pre-installed 120mm RGB LED fans at the front and one at the rear, ensuring consistent airflow. The front panel includes a mesh grille for optimal ventilation, and the top panel offers a perforated cover for additional fan/radiator mounting.
• Illuminated I/O Panel: The side-mounted I/O panel includes standard audio ports, USB 3.0 ports, and a USB-C port, all featuring their own RGB illumination.
• پانل‌های شیشه سکوریت: Two tempered glass side panels provide a clear view of internal components. The right-side panel is partially tinted to conceal the power supply tunnel while highlighting SSDs or HDDs.
• فضای داخلی جادار: Designed to accommodate large components, including graphics cards up to 42.5 cm, power supplies up to 24 cm, and CPU coolers up to 16.5 cm.
• مدیریت کارآمد کابل: Features a spacious, foldable cable compartment and a sliding cable cover to keep wiring organized and out of sight.
• گزینه های ذخیره سازی: Supports up to seven 2.5-inch drives or four 3.5-inch drives.

3. محتویات بسته

The SHARKOON Elite Shark CA300T PC Case package typically includes:

• SHARKOON Elite Shark CA300T PC Case (White)
• Pre-installed 120mm RGB LED Fans (3x Front, 1x Rear)
• جعبه لوازم جانبی (پیچ، بست کابل، استندآف و غیره)
• راهنمای کاربر (این سند)

Note: Specific contents may vary slightly. Please check the packaging for a complete list.

۱. دستورالعمل‌های راه‌اندازی

Follow these steps to set up your SHARKOON Elite Shark CA300T PC case and install your components.

۱. آماده‌سازی پرونده

1. جعبه را باز کنید: کیس کامپیوتر را با دقت از بسته‌بندی آن خارج کنید.
2. حذف پانل های جانبی: Unscrew the thumbscrews on the rear of the case for both tempered glass side panels. Gently slide and lift the panels to remove them. Place them on a soft, flat surface to prevent scratches.
3. جعبه لوازم جانبی: جعبه لوازم جانبی داخل کیس را پیدا کنید، که شامل تمام پیچ‌ها و سخت‌افزارهای نصب لازم است.

4.2. نصب مادربرد

1. نصب Standoffs: Ensure the correct standoffs are installed for your motherboard form factor (ATX, SSI EEB). The case typically has pre-installed standoffs for standard ATX.
2. نصب شیلد ورودی/خروجی: If your motherboard requires an external I/O shield, install it into the rear opening of the case before mounting the motherboard.
3. نصب مادربرد: Carefully place your motherboard onto the standoffs, aligning the screw holes. Secure the motherboard with the provided screws.

۳. نصب منبع تغذیه (PSU)

1. موقعیت PSU: The PSU mounts at the rear bottom of the case. Slide your PSU into the designated compartment from the rear.
2. منبع تغذیه امن: Align the PSU with the screw holes and secure it with the provided screws from the rear of the case.
3. مدیریت کابل: Route PSU cables through the cutouts to the back of the motherboard tray for organized cable management.

۴. نصب درایو ذخیره‌سازی

The CA300T supports various drive configurations:

• 2.5-inch Drives (SSDs): Mount SSDs to the dedicated brackets behind the motherboard tray or within the PSU shroud.
• 3.5-inch Drives (HDDs): Install HDDs into the drive cages located under the PSU shroud.

۳.۶ نصب کارت گرافیک و کارت توسعه

1. پوشش‌های شیار را بردارید: پوشش‌های لازم برای شیارهای انبساط را از پشت کیس بردارید.
2. Install Card: کارت گرافیک یا سایر کارت‌های توسعه خود را در اسلات‌های PCIe مناسب روی مادربرد قرار دهید.
3. کارت امن: Secure the card with the provided screws.

۷. اتصال کابل‌های پنل جلویی

Connect the front panel cables (USB 3.0, USB-C, HD Audio, Power Switch, Reset Switch, Power LED, HDD LED) to their corresponding headers on your motherboard. Refer to your motherboard manual for exact pin layouts.

4.7. مجمع نهایی

1. مدیریت کابل: Use the cable ties and routing channels to organize all internal cables behind the motherboard tray.
2. وصل مجدد پانل های جانبی: Carefully reattach both tempered glass side panels and secure them with the thumbscrews.

شکل 1: داخلی view of the CA300T, highlighting component space.

5. دستورالعمل های عملیاتی

5.1. Powering On Your System

After all components are installed and cables are connected, plug your power supply into a wall outlet and flip the PSU's power switch to the 'ON' position. Press the power button on the case's front I/O panel to start your computer.

۲. کنترل روشنایی RGB

The pre-installed RGB fans and illuminated I/O panel can be controlled via your motherboard's RGB software (if compatible) or a dedicated RGB controller if included with your motherboard or purchased separately. Refer to your motherboard manual for specific RGB header locations and software instructions.

Figure 2: The CA300T with its illuminated RGB fans and distinctive front panel.

6. تعمیر و نگهداری

نگهداری منظم به تضمین عملکرد بهینه و افزایش طول عمر قطعات کامپیوتر شما کمک می‌کند.

۵.۱ تمیز کردن فیلتر گرد و غبار

The CA300T includes magnetic dust filters. It is recommended to clean these filters every 1-3 months, depending on your environment, to maintain optimal airflow and prevent dust buildup inside the case.

1. فیلترها را پیدا کنید: Identify the dust filters on the top, front, and bottom of the case.
2. حذف فیلترها: Gently pull or slide out the magnetic dust filters.
3. فیلترهای تمیز: Use a soft brush, vacuum cleaner, or rinse with water (ensure completely dry before reinstallation) to remove accumulated dust.
4. نصب مجدد فیلترها: Place the clean filters back into their respective positions.

6.2. نظافت عمومی

برای سطوح خارجی، از یک سطح نرم و نرم استفاده کنیدamp cloth to wipe down the case. Avoid abrasive cleaners or solvents that could damage the finish or tempered glass.

شکل 3: بالا view of the CA300T, showing the perforated top panel.

7 عیب یابی

این بخش به مشکلات رایجی که ممکن است هنگام راه‌اندازی یا کار با آن مواجه شوید، می‌پردازد.

۵.۱ سیستم روشن نمی‌شود

• Check PSU: Ensure the power supply unit is properly connected to the wall outlet and the PSU's power switch is in the 'ON' position.
• اتصالات پنل جلو: Verify that the power switch cable from the case's front panel is correctly connected to the motherboard's power header.
• Internal Power Cables: Confirm that all necessary power cables (24-pin ATX, CPU 8-pin, GPU PCIe) are securely connected to the motherboard and components.

۸.۲. فن‌ها نمی‌چرخند / RGB روشن نمی‌شود

• اتصالات فن: Ensure all fan power cables are securely connected to the motherboard's fan headers or a fan controller.
• RGB Connections: Verify that RGB cables are correctly connected to the motherboard's RGB headers or a dedicated RGB controller.
• نرم‌افزار/کنترل‌کننده: Check your motherboard's BIOS/UEFI settings or RGB software to ensure fans and RGB lighting are enabled and configured correctly.

7.3. USB Ports Not Functioning

• هدرهای USB داخلی: Confirm that the internal USB 3.0 and USB-C cables from the case's front panel are securely connected to the corresponding headers on your motherboard.
• درایورهای مادربرد: Ensure all necessary motherboard chipset and USB drivers are installed.

8. مشخصات فنی

9. گارانتی و پشتیبانی

9.1. گارانتی محصول

The SHARKOON Elite Shark CA300T PC Case comes with a 2 سال گارانتی on spare parts. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims.

9.2. به روز رسانی نرم افزار

Software updates, if applicable for any integrated components or controllers, are guaranteed until 13 آوریل 2030.

9.3. پشتیبانی مشتری

For technical assistance, warranty claims, or further inquiries, please contact Sharkoon customer support through their official website or the retailer where the product was purchased. Have your product model and proof of purchase ready when contacting support.